Sort by:
For use on Brew Bucket 3/8" Ball Valve. Includes:
- 4 pcs 8.5 mm x 1 mm Buna N 70 O-rings
- 2 pcs 16mm x 1.8 mm Buna N 90 O-rings
- 6 pcs total in this set (enough to replace all o-rings on one Brew Bucket valve)
Stainless steel worm style hose clamp which fits a variety of hose types.
This hose clamp features a butterfly/key type adjustment tab which makes it easier to grip onto and tighten/loosen the clamp without the need for any tools.
If a larger diameter is required then multiple worm type hose clamps can be attached together.
Sizes available:
- 14-25mm
- 21-38mm
From: Kegland
A quality mash paddle is an essential piece of equipment for all-grain brewers.
This high quality stainless steel mash paddle is approximately 61cm long and will make stirring the mash and avoiding dough balls a much simpler task. Avoiding the formation of dough balls during the mash is important to ensure the full extract potential of the mash is achieved.
The paddle is also perfect for all other stirring duties and may even be used to knock down the hot break at the beginning of the boil.
This is a high quality stainless steel spoon with long handle approximately 53cm in length.
It is well suited to all stirring duties and can be used to take samples from the mash tun or boil kettle.
It is made of heavy-duty stainless steel so it will not warp due to heat, and is corrugated to help prevent it from bending.
A submersible pump, 2000L/H, 3.2m head, which is the same as what is supplied with the Bucket Blaster, if you need a replacement.
From: Kegland
A replacement mecanicco swing lid for the 5L Glass Jar Demijohn with mecanicco Swing Lid. Not suitable for the 5L Glass Jar Demijohn with Screw Cap/Lid.
Thermometer With Clip - a multi-purpose thermometer you can use when brewing beer, heating milk for cheese making, or frothing milk for coffee.
This Thermometer With Clip has a long stem and a clip that you can use to attach the thermometer to the side of your equipment.
The thermometer is made of stainless steel that is durable and corrosion-resistant. The dial is large which makes it easy to note the reading.
Probe length: 125mm
Temperature range: 0℃ - 110℃
From: Krome Dispense
Thread seal tape (also known as PTFE tape or plumber's tape) is a polytetrafluoroethylene (PTFE) film tape commonly used in plumbing for sealing pipe threads.
Thread seal tape lubricates allowing for a deeper seating of the threads, and it helps prevent the threads from seizing when being unscrewed. The tape also works as a deformable filler and thread lubricant, helping to seal the joint without hardening or making it more difficult to tighten, and instead making it easier to tighten.
Typically the tape is wrapped around a pipe's thread three times before it is screwed into place.
Standard 2" tri-clamp compatible with Grainfather GF30 Conical Fermenter Dual Valve as well as G40/G70 distilling attachments.
A 1.5 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 1.5 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 1.5 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 1.5" Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.
A 1.5 inch silicone tri-clover/tri-clamp seal.
A 2 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 2 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 2 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 2" Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.
A 2 inch silicone tri-clover/tri-clamp seal.
A 304 stainless steel 2 inch -4 inch Tri-clover adaptor.
A 4 inch Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.
A 4 inch silicone tri-clover/tri-clamp seal.
A 1.5 inch triclover sightglass made from 304 stainless steel.
Specifications
- Made from 304 stainless steel
- Viewing lens is High Borosilicate glass
- Operating Temp: -20-+135℃
- Max pressure: 40PSI
- Weight: 1.5kg
- Dimensions: 15cm × 18cm × 11cm
A 2 inch tri clover sight glass made from 304 stainless steel.
Specifications
- Made from 304 stainless steel
- Viewing lens is High Borosilicate glass
- Operating Temp: -20-+135℃
- Max pressure: 40PSI
- Weight: 1.5kg
- Dimensions: 15cm × 18cm × 11cm
A weldless kettle conversion kit - easily convert any kettle without welding. All you need is a 7/8″ holesaw, step drill, or hole punch and pliers.
Includes:
- stainless steel bulkhead
- stainless steel ball valve
- stainless steel hose barb
From: Krome Dispense
The Wine Thief is the simplest way of getting a sample from your fermenter. The unique design allows you to insert a standard hydrometer directly into The Thief to take a gravity reading. Just touch the tip to the wall of the fermenter to empty The Thief.
Note: Does not fit 5L Demijohn.
