Sort by:
Beer (black) connector with barb for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Duotight 8mm x Ball Lock Disconnect (Black + Yellow/Liquid).
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
Some of the features include:
-
Duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Overmolded Poppet
The overmolded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmolded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
-
High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Duotight 9.5mm x Ball Lock Disconnect (Black + Yellow/Liquid).
Note: this is the 9.5mm disconnect - the larger size for faster flow transfers. If you are looking for the 8mm disconnect, you'll find it here.
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
Some of the features include:
-
Duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Overmolded Poppet
The overmolded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmolded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
-
High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Duotight 8mm x Flow Control Ball Lock Disconnect (Black-Yellow/Liquid).
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact compared to the previous Stainless Steel Flow Control Ball Lock that has been discontinued due to the difficulty in repeated tooling and overall cost of raw materials.
The flow control ball lock disconnect is made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
Why not a flow control tap/devices?
Flow control devices are good but they inherently can create a small amount of turbulence and therefore can cause foaming. In the past flow control taps have been the only common option. Flow control taps are popular, however they have the issue that due to the fact they are placed right at the end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution.
Flow control ball lock disconnects like these on the other hand, have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason flow control ball lock disconnects like these have significantly better performance, allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.
Some of the features include:
-
New POK Injection-moulded Design - Like all new Duotight push in fittings that Kegland bring to market, all of them are manufactured with polyketone plastic (POK). This aids in chemical resistance, tensile strength, and toughness.
-
Duotight push in - These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact - The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Over moulded Poppet - The over moulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly - Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance - No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM over moulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness - This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough.
From: Kegland
Seal Kit - duotight 8mm x Flow Control Ball Lock Disconnect
Please refer to the product photos for an exploded diagram of where the replacement seals and poppet placement.
CM Becker are high quality disconnects made in Germany and assembled in the USA. They are:
- NSF approved,
- use FDA approved materials,
- and have SK approved materials(European).
This is a liquid disconnect for a Cornelius or Firestone ball lock keg with a 1/4 inch MFL connection. Can be used in conjunction with a Barbed Swivel Nut - 1/4 inch or Duotight 8mm - MFL Connector.
Beer (black) connector with MFL thread for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Stainless Steel beer disconnect with MFL fitting for ball lock corny kegs.
Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.
From: Kegland
This easy to use and compact spunding valve is handy for keg transfers or pressurised fermentations when you want to limit oxygen exposure and use counter pressure in the keg you are filling into or in the fermenter you are using.
This new improved G2 model has several upgrades:
1. duotight fitting where the gauge attaches
- This allows for a multitude of different options such as digital gauge or larger gauge to be purchased separately and upgraded.
2. Manual ring pull pressure relief
- This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually.
3. Option for Several Colour Coded PRVs to be used
Yellow - 1.2bar (17psi)
Red - 2.5bar (35psi)
Green - 4.5bar (65psi)
Grey - 7bar (100psi)
This is a low profile option only 4.5cm in height. This spunding valve fits to standard gas posts on your fermenter or keg.
It works right out of the box but has several upgrade options as shown in the images.
From: Kegland
Duotight 8mm x Ball Lock Disconnect (Grey + Red/Gas)
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassmble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
Some of the features include:
-
Duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Overmoulded Poppet
The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
-
High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Duotight 6.35mm (1/4") x Ball Lock Keg Connector (Grey-Red/Gas).
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit:
6.35mm duotight compatible barbs. Like the Duotight Picnic Tap or Carbonation Caps (Yellow, Red, Stainless).
Some of the features include:
1. Duotight push in
These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
2. Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
3. Overmoulded Poppet
The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
4. Tool-Less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
5. Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
6. Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
7. High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
CM Becker are high quality disconnects made in Germany and assembled in the USA. They are:
- NSF approved,
- use FDA approved materials,
- and have SK approved materials(European).
This is a gas disconnect for a Cornelius or Firestone ball lock keg with a 1/4 inch MFL connection. Can be used in conjunction with a Barbed Swivel Nut - 1/4 inch or Duotight 8mm - MFL Connector.
Gas (grey or white) connector with MFL thread for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Stainless Steel gas disconnect with MFL fitting for ball lock corny kegs.
Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.
From: Kegland
A Ball Lock Gas Post for corny kegs.
Note: Poppet not included but can be purchased separately..
Ball Lock Keg Liquid Jumper Post - Double Ended Corny Post
We've seen some nifty tricks of how people wash their Kegerator lines if they have multiple taps. This compact solution is going to make that routine cleaning day a breeze without having to swap disconnects to the cleaning keg/bottle or dismantling multiple ball locks. Just jump on the jumper post.
This double ended cornelius post does not have a spring / poppet. It just has a piece of bar that activates the ball lock disconnect wide open.
This double ended post will only work with liquid Ball Lock posts.
Please note it is a single piece that cannot be undone from the middle.
From: Kegland
A Ball Lock Liquid Post for corny kegs.
Note: Poppet not included but can be purchased separately..
The posts include a 20mm long thread, an o-ring, poppet, locking nut and short dip tube. This would enable you to make a keg out of any pressure vessel if you wanted to. The assembly can also be fitted to regulators, gas manifolds and various other items.
Both Gas and Liquid posts available.
From: Kegland
A Barbed Swivel Nut, often used for MFL fittings.
Bore sizes usually available:
- 4.76mm (3/16")
- 6.35mm (1/4")
It can be used for both gas and liquid. You should also purchase a stainless Oetiker Clamp or Worm Clamp to secure the connected lines.
This is quality beer/gas line for your kegging system.
The amount of beer line required to achieve a balanced system and avoid a glass full of foam depends on a number of different variables. Here is a link to a calculator that will help you determine the amount of line required to help you pour foam free beer.
Price is per metre - order as many metres as required
Dimensions/Options:
- 5.5mm internal / 8mm external
- 6mm internal / 10mm external
Note: product and colour may vary from photo shown.
High quality beer dispensing parts like this one are made of stainless steel to ensure that the taste of your beer is not compromised.
Material: stainless steel 304
From: Krome Dispense
This new EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various DuoTight, John Guest or other push in fittings. The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.
Inner Barrier
The inner barrier is made from a proprietary polymer that provides an excellent gas barrier. The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss. So your beer will stay fresher for longer and not loose carbonation like other beer line types. In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period. EVABarrier tubing is better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.
Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.
The amount of beer line required to achieve a balanced system and avoid a glass full of foam depends on a number of different variables. Here is a link to a calculator that will help you determine the amount of line required to help you pour foam free beer.
Price is per metre - order as many metres as required
Dimensions/Options:4mm internal (8mm external)
5mm internal (8mm external)
6.3mm internal (9.5mm external)
Pressure Rating (with 1.5 safety factor):
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)
From: Kegland
A 12m roll of EVABarrier line.
Looking to purchase by the meter, then you'll find it here.
This new EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various DuoTight, John Guest or other push in fittings. The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.
Inner Barrier
The inner barrier is made from a proprietary polymer that provides an excellent gas barrier. The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss. So your beer will stay fresher for longer and not loose carbonation like other beer line types. In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period. EVABarrier tubing is better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.
Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.
Dimensions/Options:
4mm internal (8mm external)
5mm internal (8mm external)
Pressure Rating (with 1.5 safety factor):
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)
Length: 12m
From: Kegland
This mini draft tapping head will turn your growler into a portable keg system.
The growler is purchase separately and can be purchased at this link: Ultimate Vacuum Insulated Growler
This convenient growler tapping head is the best way to keep your precious beer fresh and carbonated in the beer. The pressure applied by CO2 will keep your beer away from damaging oxygen and keep the beer carbonated for ages.
The vacuum walled growler will also keep the beer cold for ages meaning you don't even need a chilly bin or cooler box.
This system doesn't include the regulator, growler or co2 bulbs. These can be purchased separately.
Convenient hand-held beer dispensing gun for pouring stouts or nitro beers.
The beer gun has a long narrow nozzle with a restrictor. This helps mixing nitrogen into the beer well and results in a silky pour.
- Stainless steel 304 grade construction.
- Single handle press and release easy action pouring.
- Narrow spout mixes nitrogen with the beer well. Gives the silky texture to the drink.
- Black convenient grip handle.
From: Krome Dispense
Duotight Bottle Filler Beer Gun - Gen2
Have a keg of beer, but want to fill some bottles to take with you to the game, beach, or friend's house? This beer gun is a great way to fill bottles from a keg. Every part that comes into contact with your beer is stainless steel. This unit features a CO2 purge, which helps to prevent oxidation during filling.
Now with duotight fittings as standard making the set up and pack away process extremely simple and secure.
The features, coupled with a CO2 jacketing tube for bottle purging and ergonomic valve actuators, makes filling bottles faster, intuitive, more accurate, and easier than ever! Because the Bottle Filler Beer Gun doesn't require a pressurising stopper, you can fill a bottle of any depth without buying different stem lengths or adding plastic hose extensions.
Includes:
1 x Bottle Filler Beer Gun Unit with gas and liquid trigger with silicone tip. Replacement Tips can be found here.
1 x 1/4" x 6.35mm duotight fitting
1 x Red Gas Carbonation Cap x 6.35mm Male Duotight fitting (Connect your gas ball lock line directly to the unit, no longer a permanent fitting!)
1 x 1.5-2m Length of 4mm x 8mm EVABarrier Hosing
1 x 8mm Compression x 8mm female duotight fitting elbow
1 x 8mm Duotight x yellow/black liquid ball lock disconnect
Please use the photos above as your instruction manual on how to assemble.
We also have the non-Duotight Beer Gun Bottle Filler.
From: Kegland
Replacement rubber tip for the Kegland Beer Gun Bottle Filler. Sold individually.
From: Kegland
8mm OD Beer Line Tidy (BLT) - Beer and Gas Line Organiser.
This beer line tidy is a handle little part that will help you organise your beer and gas line inside your fridge, keezer, kegerator or cellar. Designed to suit 8mm outer diameter hosing like the 4mm x 8mm EVABarrier and 5mm x 8mm EVABarrier hosing.
Simply remove the paper and use the strong 3M adhesive to attach this beer/gas line organiser to whatever device you like.
This keeps your beer and gas plumbing neat and tidy so your draft system looks as good as it works.
From: Kegland
From: Krome Dispense
Bronco / Picnic Party Taps are an inexpensive way to pour beer and great for portable light weight systems that you can take away with you.
Now even better with the addition of duotights. No more hose clamps or stretching hose over barbs! It also makes it easy to disconnect and balance hosing if required.
Looking for the barbed picnic tap? You'll find it here.
From: Kegland
An excellent and economical way to be able to dispense beer from a keg when it isn't connected to your main kegging system.
This simple to use plastic beer tap has a 6mm barb which will ideally suit 5mm ID beer line
This Tap to Keg Adapter and Coupling Nut will allow you to add a beer dispensing tap directly to your keg. Includes both adapter and faucet coupling nut.
Requires an MFL keg connector and beer tap, not included.
This handy tool is exactly what you need to fit numerous dispensing applications.
This new 7 in 1 tool is also suitable for duotight fittings so it's been improved since the older 5 in 1 tools.
Use it for these tasks:
- Nut behind your taps (27mm Spanner)
- Ring collar connecting your tap to the shank
- Attaching your type 30 Regulator to your CO2 Bottle
- FFL fitting to tighten/undo an MFL connection. (e.g. Barbed fitting on CO2 Regulator)
- The handy dandy bottle opener
- Remove 8mm tubing from duotight fittings
- Remove 9.5mm tubing from duotight fittings
From: Kegland
A standard plastic handle with a threaded brass insert that fits most beer taps.
A chrome plated brass handle for beer taps. Fits most faucets.
From: Krome Dispense
A European-style plastic handle for beer taps. Fits most faucets.
