Sort by:
Perfect for packaging, storing/aging and enjoying your award winning brew!
Features:
- 24 Food Grade Amber Glass bottles, with silicone seal and PP swing top cap.
- Easy to use. A great alternative to traditional glass bottles as there is no need for a capping tool.
- Amber glass reflects harmful UV light which can skunk your beer.
- Bottles and swing top lids are easy to clean: dishwasher safe.
- Replacement swing top lid and seal sold separately.
From: Kegland
A Hex Base stand for Fermzilla All Rounders.
This base is built sturdy and strong, able to take a beating in your brewery.
The 24 sticky dots make sure it stays attached to your Fermzilla. Be careful with placement because once its on, it isn't coming off easily!
Getting the All Rounder level for accurate litre measurements only has to be done once! Not every brew day. No more dealing with tightening straps each brew saving time on brew day.
Fits both sizes of allrounder:
Beer (black) connector with barb for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Duotight 8mm x Ball Lock Disconnect (Black + Yellow/Liquid).
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
Some of the features include:
-
Duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Overmolded Poppet
The overmolded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmolded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
-
High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Duotight 9.5mm x Ball Lock Disconnect (Black + Yellow/Liquid).
Note: this is the 9.5mm disconnect - the larger size for faster flow transfers. If you are looking for the 8mm disconnect, you'll find it here.
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
Some of the features include:
-
Duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Overmolded Poppet
The overmolded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmolded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
-
High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Duotight 8mm x Flow Control Ball Lock Disconnect (Black-Yellow/Liquid).
This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact compared to the previous Stainless Steel Flow Control Ball Lock that has been discontinued due to the difficulty in repeated tooling and overall cost of raw materials.
The flow control ball lock disconnect is made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
Why not a flow control tap/devices?
Flow control devices are good but they inherently can create a small amount of turbulence and therefore can cause foaming. In the past flow control taps have been the only common option. Flow control taps are popular, however they have the issue that due to the fact they are placed right at the end of the beer line they have no head pressure. As a result, any turbulence created can cause foaming and carbonation to come out of solution.
Flow control ball lock disconnects like these on the other hand, have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason flow control ball lock disconnects like these have significantly better performance, allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.
Some of the features include:
-
New POK Injection-moulded Design - Like all new Duotight push in fittings that Kegland bring to market, all of them are manufactured with polyketone plastic (POK). This aids in chemical resistance, tensile strength, and toughness.
-
Duotight push in - These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact - The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Over moulded Poppet - The over moulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly - Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance - No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM over moulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness - This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough.
From: Kegland
Seal Kit - duotight 8mm x Flow Control Ball Lock Disconnect
Please refer to the product photos for an exploded diagram of where the replacement seals and poppet placement.
Beer (black) connector with MFL thread for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Stainless Steel beer disconnect with MFL fitting for ball lock corny kegs.
Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.
From: Kegland
This easy to use and compact spunding valve is handy for keg transfers or pressurised fermentations when you want to limit oxygen exposure and use counter pressure in the keg you are filling into or in the fermenter you are using.
This new improved G2 model has several upgrades:
1. duotight fitting where the gauge attaches
- This allows for a multitude of different options such as digital gauge or larger gauge to be purchased separately and upgraded.
2. Manual ring pull pressure relief
- This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually.
3. Option for Several Colour Coded PRVs to be used
Yellow - 1.2bar (17psi)
Red - 2.5bar (35psi)
Green - 4.5bar (65psi)
Grey - 7bar (100psi)
This is a low profile option only 4.5cm in height. This spunding valve fits to standard gas posts on your fermenter or keg.
It works right out of the box but has several upgrade options as shown in the images.
From: Kegland
Duotight 8mm x Ball Lock Disconnect (Grey + Red/Gas)
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassmble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.
Some of the features include:
-
Duotight push in
These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
-
Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
-
Overmoulded Poppet
The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
-
Tool-less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
-
Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
-
Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
-
High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Duotight 6.35mm (1/4") x Ball Lock Keg Connector (Grey-Red/Gas).
This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!
Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.
The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.
The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.
This particular ball lock disconnect has been designed to suit:
6.35mm duotight compatible barbs. Like the Duotight Picnic Tap or Carbonation Caps (Yellow, Red, Stainless).
Some of the features include:
1. Duotight push in
These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
2. Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
3. Overmoulded Poppet
The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
4. Tool-Less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
5. Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
6. Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
7. High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.
From: Kegland
Gas (grey or white) connector with MFL thread for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Stainless Steel gas disconnect with MFL fitting for ball lock corny kegs.
Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.
From: Kegland
A Ball Lock Gas Post for corny kegs.
Note: Poppet not included but can be purchased separately..
Ball Lock Keg Liquid Jumper Post - Double Ended Corny Post
We've seen some nifty tricks of how people wash their Kegerator lines if they have multiple taps. This compact solution is going to make that routine cleaning day a breeze without having to swap disconnects to the cleaning keg/bottle or dismantling multiple ball locks. Just jump on the jumper post.
This double ended cornelius post does not have a spring / poppet. It just has a piece of bar that activates the ball lock disconnect wide open.
This double ended post will only work with liquid Ball Lock posts.
Please note it is a single piece that cannot be undone from the middle.
From: Kegland
A Ball Lock Liquid Post for corny kegs.
Note: Poppet not included but can be purchased separately..
This new EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various DuoTight, John Guest or other push in fittings. The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.
Inner Barrier
The inner barrier is made from a proprietary polymer that provides an excellent gas barrier. The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss. So your beer will stay fresher for longer and not loose carbonation like other beer line types. In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period. EVABarrier tubing is better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.
Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.
The amount of beer line required to achieve a balanced system and avoid a glass full of foam depends on a number of different variables. Here is a link to a calculator that will help you determine the amount of line required to help you pour foam free beer.
Price is per metre - order as many metres as required
Dimensions/Options:4mm internal (8mm external)
5mm internal (8mm external)
6.3mm internal (9.5mm external)
Pressure Rating (with 1.5 safety factor):
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)
From: Kegland
A 12m roll of EVABarrier line.
Looking to purchase by the meter, then you'll find it here.
This new EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various DuoTight, John Guest or other push in fittings. The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.
Inner Barrier
The inner barrier is made from a proprietary polymer that provides an excellent gas barrier. The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss. So your beer will stay fresher for longer and not loose carbonation like other beer line types. In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period. EVABarrier tubing is better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.
Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.
Dimensions/Options:
4mm internal (8mm external)
5mm internal (8mm external)
Pressure Rating (with 1.5 safety factor):
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)
Length: 12m
From: Kegland
This mini draft tapping head will turn your growler into a portable keg system.
The growler is purchase separately and can be purchased at this link: Ultimate Vacuum Insulated Growler
This convenient growler tapping head is the best way to keep your precious beer fresh and carbonated in the beer. The pressure applied by CO2 will keep your beer away from damaging oxygen and keep the beer carbonated for ages.
The vacuum walled growler will also keep the beer cold for ages meaning you don't even need a chilly bin or cooler box.
This system doesn't include the regulator, growler or co2 bulbs. These can be purchased separately.
Duotight Bottle Filler Beer Gun - Gen2
Have a keg of beer, but want to fill some bottles to take with you to the game, beach, or friend's house? This beer gun is a great way to fill bottles from a keg. Every part that comes into contact with your beer is stainless steel. This unit features a CO2 purge, which helps to prevent oxidation during filling.
Now with duotight fittings as standard making the set up and pack away process extremely simple and secure.
The features, coupled with a CO2 jacketing tube for bottle purging and ergonomic valve actuators, makes filling bottles faster, intuitive, more accurate, and easier than ever! Because the Bottle Filler Beer Gun doesn't require a pressurising stopper, you can fill a bottle of any depth without buying different stem lengths or adding plastic hose extensions.
Includes:
1 x Bottle Filler Beer Gun Unit with gas and liquid trigger with silicone tip. Replacement Tips can be found here.
1 x 1/4" x 6.35mm duotight fitting
1 x Red Gas Carbonation Cap x 6.35mm Male Duotight fitting (Connect your gas ball lock line directly to the unit, no longer a permanent fitting!)
1 x 1.5-2m Length of 4mm x 8mm EVABarrier Hosing
1 x 8mm Compression x 8mm female duotight fitting elbow
1 x 8mm Duotight x yellow/black liquid ball lock disconnect
Please use the photos above as your instruction manual on how to assemble.
We also have the non-Duotight Beer Gun Bottle Filler.
From: Kegland
Replacement rubber tip for the Kegland Beer Gun Bottle Filler. Sold individually.
From: Kegland
8mm OD Beer Line Tidy (BLT) - Beer and Gas Line Organiser.
This beer line tidy is a handle little part that will help you organise your beer and gas line inside your fridge, keezer, kegerator or cellar. Designed to suit 8mm outer diameter hosing like the 4mm x 8mm EVABarrier and 5mm x 8mm EVABarrier hosing.
Simply remove the paper and use the strong 3M adhesive to attach this beer/gas line organiser to whatever device you like.
This keeps your beer and gas plumbing neat and tidy so your draft system looks as good as it works.
From: Kegland
From: Krome Dispense
Bronco / Picnic Party Taps are an inexpensive way to pour beer and great for portable light weight systems that you can take away with you.
Now even better with the addition of duotights. No more hose clamps or stretching hose over barbs! It also makes it easy to disconnect and balance hosing if required.
Looking for the barbed picnic tap? You'll find it here.
From: Kegland
An excellent and economical way to be able to dispense beer from a keg when it isn't connected to your main kegging system.
This simple to use plastic beer tap has a 6mm barb which will ideally suit 5mm ID beer line
This handy tool is exactly what you need to fit numerous dispensing applications.
This new 7 in 1 tool is also suitable for duotight fittings so it's been improved since the older 5 in 1 tools.
Use it for these tasks:
- Nut behind your taps (27mm Spanner)
- Ring collar connecting your tap to the shank
- Attaching your type 30 Regulator to your CO2 Bottle
- FFL fitting to tighten/undo an MFL connection. (e.g. Barbed fitting on CO2 Regulator)
- The handy dandy bottle opener
- Remove 8mm tubing from duotight fittings
- Remove 9.5mm tubing from duotight fittings
From: Kegland
These unique silicone faucet plugs are a universal size so they suit any tap faucet of a diameter 10mm up to 17mm. Perfect for Nukatap and Intertap taps.
The plug is an economical solution for controlling fruit flies, yeast, and bacteria bulidup when the faucet is not in use.
The silicone compound is resistant to caustic and acid-based cleaners as well as high temperature so it is dishwasher safe.
This item also has a dual-use with the BrewZilla Overflow pipe seal for filling the malt pipe with your grain bill.
Features:
- Food grade silicone
- Fits all Nukatap taps, pluto guns, fermenter taps, and many other tap designs
Note: only available in black. Nukatap tap not included.
Our standard bench capper provides an easy way to cap your beer bottles.
It is made from steel and with rubber grip pad so your bottles don't slip off the platform
This bottle capper can be used on different size bottles as the height of the bell can be adjusted, and it can be bolted to sturdy surface.
Features:
- Easy to use and adjust to required heights depending on bottle size
- Comes with a standard bell which has a built in magnet to hold the bottle cap
- Simply place bottle caps in the bell then place the bottle underneath and pull the handle down
The capper is shipped flat-packed and needs assembling before use.
From: Kegland
The Black Phantom Font Kit is the perfect match for your Black Punisher or Stealth Bomber Nukataps. Made of high quality 304 stainless with a classy matte black finish, it is sure to add a touch of panache to your kegerator!
This duotight font kit includes:
- Double Tap Black Punisher Stainless Font Only (includes gasket)
- 2 x duotight compatible Short Shank
- 2 x Black Plastic Tap Handle
- Pre-Cut - 4mm ID x 8mm OD Evabarrier Beer Line and 5mm ID x 8mm OD Evabarrier Gas Line.
- 2 x duotight 6.5mm x 8mm push in fittings to easily join the beer line to the tap shank
- 4 x Metric M5 stainless screws to secure the font to the fridge
- 1 x duotight tee pieces for the gas line
- A 7 in 1 tool for assembly
Please note: Nukataps are not included
These fonts are also insulated with closed cell insulation foam inside the font so it fits snugly preventing heat ingress into your beer.
Specs:
- 320mm Tall (without taps)
- 78mm Diameter
- Base Collar Diameter 111mm
- Internal Foam Insulation
Please note: handle with care. Scratches will be more visible than the Brushed Stainless Steel model.
This font kit has been designed to suit the Series 4, Series X and Grand Deluxe Ranges of Kegerators.
The holes in the flange are pre-drilled so they can be attached easily using the metric M5 screws.
From: Kegland
The Black Phantom Font Kit is the perfect match for your Black Punisher or Stealth Bomber Nukataps. Made of high quality 304 stainless with a classy matte black finish, it is sure to add a touch of panache to your kegerator!
This duotight font kit includes:
- Triple Tap Black Punisher Stainless Font Only (includes gasket)
- 3 x duotight compatible Short Shank
- 3 x Black Plastic Tap Handle
- Pre-Cut - 4mm ID x 8mm OD Evabarrier Beer Line and 5mm ID x 8mm OD Evabarrier Gas Line.
- 3 x duotight 6.5mm x 8mm push in fittings to easily join the beer line to the tap shank
- 4 x Metric M5 stainless screws to secure the font to the fridge
- 2 x duotight tee pieces for the gas line
- A 7 in 1 tool for assembly
Please note: Nukataps are not included
These fonts are also insulated with closed cell insulation foam inside the font so it fits snugly preventing heat ingress into your beer.
Specs:
- 320mm Tall (without taps)
- 78mm Diameter
- Base Collar Diameter 111mm
- Internal Foam Insulation
Please note: handle with care. Scratches will be more visible than the Brushed Stainless Steel model.
This font kit has been designed to suit the Series 4, Series X and Grand Deluxe Ranges of Kegerators.
The holes in the flange are pre-drilled so they can be attached easily using the metric M5 screws.
From: Kegland
Black Phantom Single Tap Stainless Font only.
The all new Phantom Series Black Font. The beautiful matte black finish looks great in a minimalist environment on the ever-popular Series X Kegerator.
These fonts are also insulated with closed cell insulation foam inside the font so it fits snugly preventing heat ingress into your beer. However, the Quadruple fonts do not have any insulation foam. If you do want to insulate these fonts, you could either use expandafoam if you're a more permanent operator, or a trimmed pool noodle.
These fonts are perfect for air cooling and use with a Font Fan.
Specifications - 1-3 taps:
- 320mm Tall (without taps)
- 78mm Diameter
- Base Collar Diameter 111mm
- Internal Foam Insulation
Specifications - 4 tap:
- 400mm Tall (without taps)
- 125mm Diameter
Please note: handle with care. Scratches will be more visible than the Brushed Stainless Steel model.
From: Kegland
The BlowTie Complete Kit (Diaphragm Spunding Valve), for pressure fermentation and pressure transfers.
Pressure Fermentations
With pressurised fermentation becoming ever more popular, it is important to have a method of regulating and controlling the residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.
Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg, it's often a good idea to have head pressure in the keg you are filling, especially if you are transferring a beverage that is already carbonated. For this reason, the BlowTie can consistently control this head pressure, giving you more consistent results and without losing carbonation in the process.
Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation. Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.
The BlowTie has been made differently, taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure. It can be easily disassembled for cleaning using a flat head screw driver.
This Kit Includes:
- 1 x Blow Tie Spunding Valve
- 1 x Duotight 8mm tee piece
- 1 x Duotight FFL to 8mm fitting
- 1 x 8mm Push in 0-40psi Gauge
- 1 x Ball Lock Disconnect (MFL) Grey/Gas
- 2 x NEW Black 8mm straight joiner pieces
Instructions:
Use the yellow adjustment knob to control the pressure coming out of the pressure vessel. Clockwise is higher pressure and anticlockwise is lower pressure. We recommend gassing a keg to a known pressure, e.g. 15psi, then attaching your Blow Tie Kit to the keg and adjust to 10psi.
Specs:
- Made from food grade acetal
- Stainless screws
- 8mm (5/16") push on both sides
- 0-40psi pressure rating
The unit can be easily disassembled for cleaning using a phillips head screw driver.
Features:
- 8mm push fit connectors
- precise pressure control
- easy to take apart and clean
- simple to adjust pressure
- made from high quality acetal
- diaphragm activated
- control pressure from 0-40psi
Pressure Fermentations
With pressurised fermentation becoming ever more popular it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.
Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg, it is often a good idea to have head pressure in the keg you are filling, especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process.
The BlowTie has been made different to traditional spunding valves by taking advantage of a diaphragm to actuate the sealing mechanism. This will release pressure from the pressure vessel with much more accurate control.
From: Kegland
Garden Hose Female x Grip Hose Connector 12mm / 1/2" Coupling
These easy to use garden hose quick connector couplings are really handy for connecting your hose to a female hose adaptor.
Specifications:
- Brass Construction
- Fits most male garden hose fittings
- 12mm ~ 1/2inch Barb with compression grip fitting
- Includes rubber washer so no teflon tape needed
From: Kegland
BrewZilla + DigiBoil S.S Adjustable Lid Clamps - Short (4pcs/set).
Get the exact tension you need with your BrewZilla, DigiBoil or even GrainFather with Kegland's Stainless Steel Adjustable Clamp Set. Adjust to your specification.
This set of 4 adjustable stainless steel clamp set suits the 35L and 65L BrewZilla Gen 3 all the way to Gen 4 as well as all 35L and 65L DigiBoils. It also suits the 12L and 24L Boiler Extensions.
How to instructions:
- You will need a pair of bolt cutters or tin snips to cut the current clamp off. (Please see product photos for optimum cut location)
- Remove the nut and bolt and thread it through the clamp. Ensure that the grooved part is facing outwards (photo for reference). If you do not have the grooved part facing outwards, the clamp will found on the round lip of the boiler.
- Loosen the bolts and spin the clamp up or down to adjust the tension. Use the nuts to lock the desired tension. It is always best to start looser than you think, then adjust tighter.
WARNING: Do not use the clamps or adjustable clamps with a glass lid, the clamps are only designed for metal steam condenser or distillation lids.
Please note: All Gen 4 35L, 65L BrewZillas will come with these in the near future as standard. Please check the body of the description/photos to confirm.
From: Kegland
