Sort by:
A 2L borosilicate Erlenmeyer conical flask that is ideal for yeast starters using a stir plate such as the Wort Whipper..
Safety warnings:
**Please still exercise care when handling these and any other Borosilicate glass.**
There is a common misconception that Borosilicate glass is virtually bulletproof and can handle any dramatic temperature that is thrown at it. This is not strictly true.
Though it does have an incredible ability to withstand sudden and drastic temperature shocks compared to your average soda-lime glass, it should still be treated consciously with care.
Cool all glassware slowly to prevent breakage, unless you are using VYCOR glassware which can go from high heat to ice water with no damage.
Do not take your boiled flask directly from the stovetop straight into a bath of ice water. Though some people do this without failure, borosilicate glass is not designed for such an application. Please allow the flask to cool for a few minutes before running under water, before placing into an ice bath; the slower you introduce your flasks to temperature changes, the longer it will last. Going from fire to ice in a matter of seconds will introduce incredible amounts of stress to the glass structure. While the glass may be able to withstand this some of the time, other times you may not be so lucky. If the temperature differential is big enough, it will shatter. All Borosilicate glass will break eventually after a number of heat/cool cycles, it is impossible to give an exact number to determine when, but this is a natural an inherent feature of the material.
Please do not boil your flasks dry or dry them out using a stove. The temperature for drying should not exceed 140°C, which a naked flame can easily exceed.
Do not heat glassware that is etched, cracked, chipped, nicked, or scratched. It is more prone to break.
Do not heat glassware directly on electrical heating elements. Excessive stress will be induced in the glass, and this can result in breakage.
Small Bubbles that are less than 5mm and not located directly on the bottom of the flask is an acceptable manufacturing blemish as per our instruction from multiple manufacturers of glass.
A 2L borosilicate Erlenmeyer conical flask that is ideal for yeast starters using a stir plate such as the Wort Whipper..
Safety warnings:
**Please still exercise care when handling these and any other Borosilicate glass.**
There is a common misconception that Borosilicate glass is virtually bulletproof and can handle any dramatic temperature that is thrown at it. This is not strictly true.
Though it does have an incredible ability to withstand sudden and drastic temperature shocks compared to your average soda-lime glass, it should still be treated consciously with care.
Cool all glassware slowly to prevent breakage, unless you are using VYCOR glassware which can go from high heat to ice water with no damage.
Do not take your boiled flask directly from the stovetop straight into a bath of ice water. Though some people do this without failure, borosilicate glass is not designed for such an application. Please allow the flask to cool for a few minutes before running under water, before placing into an ice bath; the slower you introduce your flasks to temperature changes, the longer it will last. Going from fire to ice in a matter of seconds will introduce incredible amounts of stress to the glass structure. While the glass may be able to withstand this some of the time, other times you may not be so lucky. If the temperature differential is big enough, it will shatter. All Borosilicate glass will break eventually after a number of heat/cool cycles, it is impossible to give an exact number to determine when, but this is a natural an inherent feature of the material.
Please do not boil your flasks dry or dry them out using a stove. The temperature for drying should not exceed 140°C, which a naked flame can easily exceed.
Do not heat glassware that is etched, cracked, chipped, nicked, or scratched. It is more prone to break.
Do not heat glassware directly on electrical heating elements. Excessive stress will be induced in the glass, and this can result in breakage.
Small Bubbles that are less than 5mm and not located directly on the bottom of the flask is an acceptable manufacturing blemish as per our instruction from multiple manufacturers of glass.
Digital instant read thermometer with folding probe.
A perfect pocket temperature probe for homebrewing and BBQ! Check the temperature of your mash, whirlpool additions, or use it to check the internals of that fine-looking lamb roast on the bbq! With a range of -50°C to 300°C you will be hard-pressed not to get a temperature reading.
Specifications:
- Range: -50°C ~ 300°C / -58°F ~ 572°F
- Resolution: 0.1°C
- Temperature Error: +-1°C (0~100°C)
- Power Supply: AG13 button battery x 1 (included)
Functions:
- ON/OFF
- °C/°F
- HOLD
From: Kegland
Electronic scales for measuring additions such as brewing salts and hops (0.1g to 1000g).
Adjusting your pH with brewing salts has never been easier than with this tiny pocket rocket scales. Flip the lid and get weighing because we wouldn't start brew day without one.
Specifications:
- Powered by 2 AAA batteries (batteries not included)
- Durable and compact digital pocket scale for easy portability
- Weighs items up to 1000 grams in 0.1 gram increments
- Easy-to-read, backlit LCD display; intuitive, flip-open lid protects the smooth, stainless-steel weighing surface
From: Kegland
Made of highly accurate sensors, the 40kg Home Brew Digital Scale is your best companion prior to your brew day routine. Don't take the small kitchen scales that are hard to read with a giant bucket on it. Get yourself some serious scales for some serious business!
It runs on a rechargeable battery which means you can use it anywhere you like. The battery is fully charged within 2 hours and can run up to 140 hours just from a single charge.
NOTE: All scales used for commercial purposes are required to be calibrated.
Over charging for more than 2 hours can lead to battery failure, whereby the unit would have to be wired to turn on.
Specifications:
- Power: AC or rechargeable battery
- Voltage: 220v 50Hz/60Hz
- Battery required: 4V 6AH recharge battery
- Capacity: 40kg
- Increment: 1g
- Precision: 1/3000F.S
- Display windows: Weight (5 digits), Unit price (5 digits), Total Price (6 digits)
- Platform size: 33.5x23.5cm
- Product size: 34x33x8cm
- Colour: Black (unbranded)
- Battery: 4v Lead Acid Battery (Charge for two hours at a time, do not over charge)
From: Kegland
Large stainless steel funnel with a handle for bottling spirits. Also ideal for use with paper coffee filters if transferring oak aged spirits or spirit that has been polished on carbon.
Specifications
- 14cm diameter, not including handle
- 12.5cm height
- Stainless Steel
- Dishwasher Safe
A hydrometer is an essential tool for testing starting and finishing gravity, or sugar content, in beer or wine or spirit fermentations. This is a triple scale hydrometer - specific gravity, potential alcohol and approx. sugar per litre.
Best used with a trial jar (sold separately).
Handcraft Supplies Triple Scale Fermentation Hydrometer measures the specific gravity, potential alcohol, and approx. sugar content of any fermentable liquid, whether you're making wine, cider, beer, or distilling wash.
Best used with a trial jar (sold separately).
Infrared Thermometer Gun -50C to +580C (Black)
This thermometer gun has a built-in Dual laser that can be switched On and Off. Dual laser is an important feature when choosing infrared thermometers because it allows for much higher accuracy of readings. When measuring an object a Dual Laser will help greatly in finding the convergence point of the measured target and the spot ratio, which can only be achieved with Dual Laser.
Features:
- Double Laser pointer for accurate target aiming
- Simple one-handed operation
- Laser ON/OFF Switch
- Low battery indication
- LED backlight system for operation under poor illumination
- C° / °F temperature unit conversion
- Automatic Power off in 15 seconds without any operation
- Display hold, scan function
Note:
1. When using this product to measure temperature, consider the ratio between the distance (the length from the product to the measured object) and the size of the measurement area, referred to as the object distance ratio. When the distance between the product and the measured object increases, the measurement area will increase accordingly.
2. If you want to use boiled water to measure the quality of the product, please note that when measuring boiling liquids, do not allow smoke or water vapour to contact the temperature sensing area, and keep the measurement angle at 45 ~ 60 degrees.
Specifications:
- Temperature Range: -50 to 550°C
- Accuracy: ± 2% or 2°C
- Distance Spot Ratio: 12:1
- Emissivity: 0.1~1.0(Adjustable)
- Response Time Wavelength: 500ms & (8-14) um
- Repeatability: ± 1% or 1°C
- Resolution: 1°C or 1°F
- Storage Temperature: -20-50°C
- Operating Temperature: 0-50°C
From: Kegland
Premium quality pH solutions from Hanna Instruments for calibrating your pH meter. Hanna’s line of calibration buffers have been specially formulated to have an expiration of 5 years from the date of manufacture for an unopened bottle.
Usually available for these pH levels: pH 4.01, pH 7.01
Reported values are accurate to +/- 0.01 pH at 25°C.
From: Hanna Instruments
Size: 500ml
A refractometer is used to test sugar concentrations in a solution. When light passes through a liquid it bends at an angle. Depending on the density of the liquid, this angle becomes more or less pronounced. Refractometers work using this property and translate this shifted angle of refracted light to fall on a graduated Brix chart that is viewable in the eyepiece.
When brewing a refractometer allows you to take instant gravity measurements during mash, run-off, or during the boil. A valuable tool for all grain and extract brewers alike.
As the density of wort is not the same as a sugar water solution you may wish to calibrate your refractometer when measuring wort. Click here for more information on how to do this.
When making wine a refractometer makes it very easy to measure the sugar levels at the crush or of your must.
Using a Refractometer:
To use, apply 2-3 drops to the prism face, close the cover and wait 30 seconds. Look through the eye-piece - the line on the screen will show the Brix % and Specific Gravity reading.
Calibrate the unit to 0.0 Brix before use with distilled water.
This model comes with ATC (Automatic Temperature Compensation) allowing you to use the refractometer between 10 / 30 degrees Celsius so the temperature of the sample is irrelevant.
Comes with:
- Carry case
- Pipette
- Calibration Screw Driver
Note: This tool is used to measure unfermented wort. Once alcohol is present in the wort, the use of a correction table is advised. It is possible to use a calculator to convert the reading, however it may not be as accurate as a hydrometer reading.
RAPT - Bluetooth Thermometer -20 to 300C - 20cm HTC Probe
This low energy RAPT enabled Bluetooth Thermometer is compatible with the Gen 4 BrewZillas and RAPT Temperature Controllers and RAPT Fermentation Chambers. It will not work without one or more of these devices.
By receiving multiple BLE thermometer sensors the BrewZilla can make smarter and more automated decisions on how to control the brewing or distillilation process. For example a BLE thermometer can be placed into your coolant water so you get an alarm if the temperature is too high, a BLE thermometer can be put into the middle of the malt pipe so you can more accurately control elements switching on/off to achieve a core malt pipe temperature etc.
The Google Play Android App can be downloaded via the link below.
https://play.google.com/store/
The new Bluetooth thermometer can connect up to your BrewZilla Gen 4, RAPT Temperature Controller, RAPT Fermentation Chamber and log that temperature data and manipulate fermentation/brewing and distillation profiles in the RAPT Portal (https://app.rapt.io/). This greatly reduces the need for handwritten records of your brew day as it's all done automatically. The RAPT portal also allows you to see every brew you have done in the past with logged temperatures from the main units probe and this digital thermometer. This unit can also be setup to get push notifications to your mobile phone of when to sparge for example.
Along with this ease of access and control,the RAPT BrewZilla will also allow you to fully customise your brewday with profiles specifically tuned to your style of brewing or your recipe. For example, you could set up step mash profiles using the core temperature of your mash instead of the cavity below where the probe is. Greater accuracy for a more repeatable recipe that results in much better beer!
Specifications:
- 20cm Probe Length with sharp tip~ Please remove the black plastic tip before use. That is for storage to avoid punctures / injury.
- 100cm Cable Length
- Magnetised Backing Plate (Orange)
- 2 x AAA Batteries (included)
From: Kegland
Yellow RAPT Pill - Hydrometer & Thermometer (Wifi & Bluetooth).
The RAPT Pill allows true real-time specific gravity and temperature logging and control via wifi/bluetooth integration with the RAPT fermentation chamber, RAPT mobile app or RAPT IOT.
The RAPT Pill allows you to instantly read and log the specific gravity and temperature of your fermentation via the RAPT mobile app on your compatible Android smartphone or tablet, Apple iPhone/iPad or via the RAPT IOT hub on your Windows or Mac Computer.
The RAPT Pill has a long battery life and can last 2-5 months between charges when utilising Wifi. If only using Bluetooth the the battery can last 2+ years before needing to be recharged. The RAPT Pill has a USB-C charging port on the circuit board allowing fast charging from any USB-C cable. Alternatively you can purchase the Wireless Charging Kit so you charge your pill without needing to take it apart.
The RAPT Pill is universal and is compatible with most standard carboys, cornelius kegs, stainless steel fermenters and pressurisable fermenters.
Pill Housing Design
The RAPT Pill housing boasts many advantages compared to other wireless hydrometers such as:
- Made from strong BPA Free Tritan Plastic
- Greater ergonomics - The shape of the RAPT Pill has been designed for improved usability compared to other wireless hydrometers such that the Pill seperates into two pieces at the midline of the Pill rather than requiring a difficult to remove end cap to be unscrewed.
- Sanitary design - The RAPT Pill has no exposed thread and a double o-ring seal which allows for a water-tight seal with reduced risk of infection.
- Less susceptible to error - The larger housing of the RAPT Pill compared to other wireless hydrometers means that the gravity logging is less susceptible to error from krausen, hops or CO2 bubbles from fermentation.
Different housing colours are sold separately, allowing customisation of your RAPT Pill.
Specifications:
The RAPT Pill is approximately 37mm x 125mm - compact enough to fit almost anywhere!
What is RAPT?
The RAPT IOT Hub is a free service whereby any RAPT enabled product can both log and store data to the hub where you can conveniently access this data. The RAPT hub can also allow you to control your devices remotely giving you absolute control of the device irrespective of where you are. The RAPT portal enables you to make complex temperature profiles that involve different temperature settings over time meaning you can start/run a temp profile giving you a set and forget experience. The RAPT portal also controls the alert/notification process for you so you can receive email notification in the off instance that something doesn't go to plan.
There is no limit to the number of RAPT devices you can connect the RAPT IOT Hub. This is in contrast to other popular wireless hydrometers where you are limited by the number of hydrometers you can connect to an app.
RAPT Pill - Blue Housing.
This coloured housing allows you to customise your RAPT Pill. This is purely aesthetic and means you can easily differentiate multiple RAPT Pills from each other.
Does not include clear Pill Housing, the double o-rings, or the circuit board.
From: Kegland
RAPT Pill - Clear Housing (Male Threaded - Bottom Piece).
Replace your RAPT Pill bottom housing with the RAPT Clear Housing shell. Please note there are no clear top pieces for the RAPT Pill at this stage.
RAPT Pill O-Ring sold separately.
From: Kegland
RAPT Pill - Green Housing.
This coloured housing allows you to customise your RAPT Pill. This is purely aesthetic and means you can easily differentiate multiple RAPT Pills from each other.
Does not include clear Pill Housing, the double o-rings, or the circuit board.
From: Kegland
RAPT Pill - Red Housing.
This coloured housing allows you to customise your RAPT Pill. This is purely aesthetic and means you can easily differentiate multiple RAPT Pills from each other.
Does not include clear Pill Housing, the double o-rings, or the circuit board.
From: Kegland
A replacement silicone o-ring for the RAPT Pill.
It is always wise to have a few spares in case some get pinched when tightening up the RAPT Pill.
Sold individually.
From: Kegland
Charge your Pill wirelessly with this easy-to-install upgrade kit from Kegland. The RAPT Pill is a Wifi & Bluetooth hydrometer for logging fermentation to the cloud.
This easy to install kit allows you to wirelessly charge the Pill, and also access the Pill Captive Portal without needing to open the housing to access the USB-C port!
Includes:
1 x USB-C Wireless Charging Coil
2 x Adhesive Weight Pads
1 x USB-A to USB-C cord (AU power plug not supplied)
1 x Black RAPT Wireless Charging Dock (USB-C)
If the green light does not flash green (captive portal open), it means your battery is insufficiently charged. Leave your pill on the charging pad for 24 hours or until it is fully charged (red light turns off). Then lift the Pill on and off the charging pad and it will activate the captive portal (green light will start to flash).
Note: RAPT Pill sold separately, this is for the wireless charger only.
From: Kegland
A bi-metal weldless thermometer with glass face. Ideal for fitting to your mash tun, hot liquor tank or kettle.
Features:
- Calibration screw so you can fine tune the temperature
- 304 stainless steel housing and probe
- ½” BSP thread and includes silicon and stainless steel washers.
- Temperature range -5C to 100C customised for brewing
Includes a slimline nut and 2 x silicone seals plus a stainless washer.
From: Kegland
Thermometer With Clip - a multi-purpose thermometer you can use when brewing beer, heating milk for cheese making, or frothing milk for coffee.
This Thermometer With Clip has a long stem and a clip that you can use to attach the thermometer to the side of your equipment.
The thermometer is made of stainless steel that is durable and corrosion-resistant. The dial is large which makes it easy to note the reading.
Probe length: 125mm
Temperature range: 0℃ - 110℃
From: Krome Dispense
A 200ml trial jar for hydrometer or alcometer readings that is 10 inches / 24.5cm high and made from alcohol resistant plastic. The plastic is very clear making it easy to see through.
Useable depth (approx): 255mm
The Wine Thief is the simplest way of getting a sample from your fermenter. The unique design allows you to insert a standard hydrometer directly into The Thief to take a gravity reading. Just touch the tip to the wall of the fermenter to empty The Thief.
Note: Does not fit 5L Demijohn.