This high amp power supply can also be used to power the Semi-Auto Cannular.

Specifications:

Input Voltage: 220-240V AC (50-60Hz)
Input Current: 1.9amp
Output Voltage: 24V
Output Current: 12.5amp
Efficiency: greater than 90%
PF: greater than 0.95
Overload Protection: Yes
Outlet Plug: Anderson Socket

From: Kegland

A replacement screw cap for the 5L Demijohn with Screw Cap.

A 5 litre glass jar suitable for small fermentations and the storage of spirits.

A Demijohn Bored Bung fits the opening of the jar perfectly enabling an airlock to be attached.

Add a Swing Lid or use a Demijohn Solid Bung as a stopper.

The Easy Syphon 3/8 Inch and Easy Syphon 350mm are both compatible with this demijohn.

Note: The handle and shape of the Demijohn may vary.

This 5 litre glass demijohn is perfect for small fermentations (4.5 litre / 1 gallon), the storage of spirits, and the aging/conditioning of wine or mead.

The Bung with hole #9.5 - 38mm-46mm  or Bung - Bored - 37-45mm - Silicone fits perfectly to enable an airlock to be attached so the Demijohn can be used as a fermenter.

Compatible with both the Easy Syphon 350mm and the Easy Syphon 3/8 inch.

These 0.2 micron Air Filters have a fine enough filter membrane that they can filter out microbes and bacteria.

They can be used with any oil free air compressor such as a pond pump, or other type of pump.

These can also be used as an airlock in the top of your fermenter, or to filter air going back into a cask when dispensing real ale. 

This filter is not suitable for liquids and should be discarded if it gets wet.

Barb diameter measures approximately 9mm - 9.5mm.

Standard S shape airlock for sealing your fermenter.

Please note that your fermenter will need an airlock grommet or top hat grommet (sold separately) to attach the airlock to most fermenters.

May not include red cap, depending on supplier.

The three piece airlock is a great choice for monitoring fermentation and stopping contaminant’s entering your fermenter.  Easy to fill and disassembles for superior cleaning and sanitation.

Fill with water to the indicator line and insert in drilled stopper or bung to vent gases during fermentation. Includes body, piston, and vented cap. 

This airlock is slightly shorter than the Standard S Shape Airlock.

Please note that your fermenter will need an airlock grommet or top hat grommet (sold separately).

The Airlock - Vintage Bubbler is an essential tool for home brewing fermentation. Designed to allow gases to escape while preventing outside air and contaminants from entering, it helps maintain a clean and controlled environment. 

Please note that your fermenter will need an airlock grommet or top hat grommet (sold separately) to attach the airlock to most fermenters.

A Hex Base stand for Fermzilla All Rounders.

This base is built sturdy and strong, able to take a beating in your brewery.

The 24 sticky dots make sure it stays attached to your Fermzilla. Be careful with placement because once its on, it isn't coming off easily!

Getting the All Rounder level for accurate litre measurements only has to be done once! Not every brew day. No more dealing with tightening straps each brew saving time on brew day.

Fits both sizes of allrounder:

30L FermZilla All Rounder
60L FermZilla All Rounder

Auto Syphon Racking Cane Easy Jiggler - 304 Stainless Steel - for syphoning out of a carboy, demijohn, bucket or FermZilla.  This siphon includes 150cm x 10mm ID silicone tube.

This whole assembly is plasticiser and BPA free.  It will not break like the plastic auto syphons or polycarbonate designs. 

It's made robust out of 304 grade stainless steel and is really easy to take apart for cleaning.  It's more versatile than a conventional racking cane and easier to start but at the same time similarly simple to use and clean.

Forget about fermenter taps and use a syphon.  Threaded fermenter taps are hard to clean and sanitise so having a fermenter without a tap is often the best choice, and to get the beverage out of the fermenter without a tap this siphon is the natural choice.

INSTRUCTIONS
1: Sanitise and rinse your syphon
2: Make sure you have the full vessel significantly above the empty vessel you are filling
3: Attach the curved syphon to the hose
4: Submerge the end of syphon into your full container.
5: With long swift strokes, shake the syphon tube up and down to start the syphon action

Length: 57cm
Stainless tube: 14mm OD x 12mm ID
Silicone Tube: 1.5m x 10mm ID 
From: Kegland

Beer (black) connector with barb for ball lock corny kegs.

This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.

Duotight 8mm x Ball Lock Disconnect (Black + Yellow/Liquid).

This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!

Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.

The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.

The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.

This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.

Some of the features include:

1. Duotight push in
   These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
   
   
2. Compact
   The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
   
   
3. Overmolded Poppet
   The overmolded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
   
   
4. Tool-less Disassembly
   Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
   
   
5. Extreme Chemical Resistance
   No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmolded poppet.  This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
   
   
6. Toughness
   This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
   
   
7. High Flow
   The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.

From: Kegland

Duotight 9.5mm x Ball Lock Disconnect (Black + Yellow/Liquid).

Note: this is the 9.5mm disconnect - the larger size for faster flow transfers. If you are looking for the 8mm disconnect, you'll find it here.

This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!

Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.

The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.

The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.

This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.

Some of the features include:

1. Duotight push in
   These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
   
   
2. Compact
   The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
   
   
3. Overmolded Poppet
   The overmolded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
   
   
4. Tool-less Disassembly
   Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
   
   
5. Extreme Chemical Resistance
   No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmolded poppet.  This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
   
   
6. Toughness
   This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
   
   
7. High Flow
   The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.

From: Kegland

Duotight 8mm x Flow Control Ball Lock Disconnect (Black-Yellow/Liquid).

This all new ball lock disconnect sets a new bar! The integrated duotight design means you can connect your beer line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact compared to the previous Stainless Steel Flow Control Ball Lock that has been discontinued due to the difficulty in repeated tooling and overall cost of raw materials.

The flow control ball lock disconnect is made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.

Why not a flow control tap/devices?

Flow control devices are good but they inherently can create a small amount of turbulence and therefore can cause foaming.  In the past flow control taps have been the only common option.  Flow control taps are popular, however they have the issue that due to the fact they are placed right at the end of the beer line they have no head pressure.  As a result, any turbulence created can cause foaming and carbonation to come out of solution. 

Flow control ball lock disconnects like these on the other hand, have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution.  Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues.  For this reason flow control ball lock disconnects like these have significantly better performance, allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.

Some of the features include:

1. New POK Injection-moulded Design - Like all new Duotight push in fittings that Kegland bring to market, all of them are manufactured with polyketone plastic (POK). This aids in chemical resistance, tensile strength, and toughness.

2. Duotight push in - These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!

3. Compact - The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.

4. Over moulded Poppet - The over moulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.

5. Tool-less Disassembly - Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.

6. Extreme Chemical Resistance - No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM over moulded poppet.  This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.

7. Toughness - This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough.

From: Kegland

Seal Kit - duotight 8mm x Flow Control Ball Lock Disconnect

Please refer to the product photos for an exploded diagram of where the replacement seals and poppet placement. 

CM Becker are high quality disconnects made in Germany and assembled in  the USA. They are:

• NSF approved, 
• use FDA approved materials,
• and have SK approved materials(European).

This is a liquid disconnect for a Cornelius or Firestone ball lock keg with a 1/4 inch MFL connection. Can be used in conjunction with a Barbed Swivel Nut - 1/4 inch or Duotight 8mm - MFL Connector. 

Beer (black) connector with MFL thread for ball lock corny kegs.

This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.

Stainless Steel beer disconnect with MFL fitting for ball lock corny kegs.

Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.

From: Kegland

This easy to use and compact spunding valve is handy for keg transfers or pressurised fermentations when you want to limit oxygen exposure and use counter pressure in the keg you are filling into or in the fermenter you are using.

This new improved G2 model has several upgrades:

1. duotight fitting where the gauge attaches
- This allows for a multitude of different options such as digital gauge or larger gauge to be purchased separately and upgraded.

2. Manual ring pull pressure relief
- This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually.

3. Option for Several Colour Coded PRVs to be used
Yellow - 1.2bar (17psi)
Red - 2.5bar (35psi)
Green - 4.5bar (65psi)
Grey - 7bar (100psi)

This is a low profile option only 4.5cm in height.  This spunding valve fits to standard gas posts on your fermenter or keg.

It works right out of the box but has several upgrade options as shown in the images.

From: Kegland

Duotight 8mm x Ball Lock Disconnect (Grey + Red/Gas)

This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!

Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.

The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassmble and clean.

The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.

This particular ball lock disconnect has been designed to suit 8mm outside diameter beer/gas line. Due to the integrated duotight fitting the line will simply push directly into this fitting.

Some of the features include:

1. Duotight push in
   These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!
   
   
2. Compact
   The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.
   
   
3. Overmoulded Poppet
   The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.
   
   
4. Tool-less Disassembly
   Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.
   
   
5. Extreme Chemical Resistance
   No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet.  This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.
   
   
6. Toughness
   This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!
   
   
7. High Flow
   The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.

From: Kegland

Duotight 6.35mm (1/4") x Ball Lock Keg Connector (Grey-Red/Gas).

This all new ball lock disconnect sets a new bar! The integrated Duotight design means you can connect your beer and gas line directly, easily and reliably - no need for additional fittings or clamps. It is a robust and super compact design that is incredibly easy to assemble and disassemble, making cleaning and sanitising an absolute breeze!

Made from highly chemical resistant materials with stainless springs and ball bearings - no cheap ABS plastics here - this baby is extremely resistant to commonly used chemicals such as phosphoric based sanitisers and caustics.

The incredibly small form factor allows for easy stacking of kegs. The new cap design ensures a pressure seal with just hand tightening and it can be completely taken apart for cleaning with no tools required - no need to ever have blocked poppets again when it is this easy to disassemble and clean.

The robust and compact design make this the best value and the best designed home brew quick disconnect ever manufactured.

This particular ball lock disconnect has been designed to suit:
6.35mm duotight compatible barbs. Like the Duotight Picnic Tap or Carbonation Caps (Yellow, Red, Stainless).

Some of the features include:

1. Duotight push in
These Duotight ball lock disconnects already have the Duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!

2. Compact
The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.

3. Overmoulded Poppet
The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.

4. Tool-Less Disassembly
Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It's literally never been easier to remove hop particles from your ball lock disconnects.

5. Extreme Chemical Resistance
No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.

6. Toughness
This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don't be fooled by the small form factor - these bad boys are tough!

7. High Flow
The internal design of these allows for faster flow meaning you can slightly quicker transfers when compared to other plastic ball lock disconnects.

From: Kegland

CM Becker are high quality disconnects made in Germany and assembled in  the USA. They are:

• NSF approved, 
• use FDA approved materials,
• and have SK approved materials(European).

This is a gas disconnect for a Cornelius or Firestone ball lock keg with a 1/4 inch MFL connection. Can be used in conjunction with a Barbed Swivel Nut - 1/4 inch or Duotight 8mm - MFL Connector. 

Gas (grey or white) connector with MFL thread for ball lock corny kegs.

This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.

Stainless Steel gas disconnect with MFL fitting for ball lock corny kegs.

Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.

From: Kegland

A Ball Lock Gas Post for corny kegs. 

Note: Poppet not included but can be purchased separately..

Ball Lock Keg Liquid Jumper Post - Double Ended Corny Post

A Ball Lock Liquid Post for corny kegs.

Note: Poppet not included but can be purchased separately..

A 2-piece ball valve made from 316 stainless steel 

Features

• BSP threaded ends - female
• Maximum pressure 1000PSI / 69Bar W.O.G. (Water, Oil, Gas)
• PTFE seal maximum temperature 200°C
• Full port
• Lockable latch handle

A 1/2 inch ball valve assembly with a maximum operating temperature of 200℃ consisting of:

• 316 Stainless Steel 1/2 inch hex nipple
• 316 Stainless Steel 1/2 inch 2pc ball valve
• 316 Stainless Steel 1/2 inch male hosetail

Perfectly suited for use with the G70 and G40 to allow quick drainage from the bottom of the unit.

We recommend using thread tape to ensure a complete and leak proof seal. 

A 316 stainless steel mini ball valve (female - female) with 1/2 inch BSP thread.

Features

• BSP threaded ends
• Reduced port
• Maximum pressure 900PSI / 63Bar
• EPDM seal maximum temperature 120°C

A Barbed Swivel Nut, often used for MFL fittings.

Bore sizes usually available:
- 4.76mm (3/16")
- 6.35mm (1/4")

It can be used for both gas and liquid. You should also purchase a stainless Oetiker Clamp or Worm Clamp to secure the connected lines.