Sort by:
Jazz up your Kegerator or commercial beverage dispensary with these stylish decal holders. Made from plated chrome plastic, with soft padding components as to not scratch your taps when attached are surely there to catch your eye.
These decal holders will fit any tap system. Their unique clamp on design means you don't have to take off your tap to put these on. You will need a phillips head screw driver to remove the two screws.
As the name says, this will fit a 82mm Diameter Decal/Sticker/Label.
From: Kegland
This adapter is suitable for the Mini Duotight Regulator to fit a threaded Sodastream cylinder.
Please note: The adaptor can only engage the cylinder via the round knob. It cannot retract / disengage. Always use two spanners / adjustable wrenches when attaching this to your sodastream.
Specifications:
5/8' 18TPI 18UNF male to G1/2 female
From: Kegland
A carbonation or aeration diffusion stone, either 0.5 or 2.0 micron. This can be used as a way to aerate your wort prior to fermentation, or to speed up carbonation of the finished beer. The barb fits 1/4" (6.35mm) ID tubing.
If you're looking for diffusion stones with MFL thread, you'll find them here.
From: Kegland
A carbonation or aeration diffusion stone, 2.0 micron, with MFL thread. This can be used as a way to aerate your wort prior to fermentation, or to speed up carbonation of the finished beer.
If you're looking for barbed diffusion stones, you'll find them here.
From: Kegland
The DigiBoil (digital turbo boiler) is a quality made 304 grade stainless steel turbo boiler.
The 35 litre size is the total rated size to the brimful. If using the DigiBoil as a brew kettle do not fill to greater than 25L-30L to ensure you have sufficient head space to comfortably contain the hot break and avoid a boil over.
The boiler has a quality made stainless tap with stainless barb and 1/2 inch thread so you can attach the wide range of half inch fittings such as camlocks.
The unit comes with a concealed element for easy cleaning.
The digital display can be set from 0℃ and up to 140℃ with 1℃ increments and 1℃ resolution on the display.
The side of the boiler is pre-marked with graduations in litres and gallons that are accurate to +/- 1 litre.
- Litre and Gallon Graduations
- Stainless steel tap with barb and 1/2 thread
- Dual element control (so you can adjust the power from 500watts, 1900watts or 2400watts)
- Easy to use
- Great for use as a hot liquor tank, boiler, or hot water urn
- Concealed element for easy cleaning
- Can also be used for sous vide cooking
Want to save some power?
You can also purchase the neoprene jacket/parka that fits this unit here. This will reduce your heat loss by about 200-300 watts.
This digital turbo boiler is a quality made 304 grade stainless steel turbo boiler.
The 65 Litre size is the total rated size brimful, so typically if you are using this as a beer boiler you would probably only fill it up to 50-60L so you had 5-10 litres of head space to boil comfortably.
The boiler has a quality made stainless tap with stainless barb and 1/2inch thread so you can attach the wide range of other half inch fittings such as camlocks and many other fittings that we can supply.
The unit comes with a concealed element for easy cleaning.
The digital display can be set from 0℃ and up to 140℃ with 1℃ increments and 1℃ resolution on the display.
The side of the boiler is pre-marked with graduations in litres and gallons that are accurate to +/- 1 litre.
- Litre and Gallon Graduations
- Stainless steel tap with barb and 1/2 thread
- Triple element control (so you can adjust the power from 500watts, 1000watts, 1500watts, 2000watts, 2500watts, 3000watts and 3500watts! )
- Easy to use
- Great for use as a hot liquor tank, boiler, or hot water urn
- Concealed element for easy cleaning
- Can also be used for sous vide cooking
Dimensions: 42cm diameter x 74cm high
You can also purchase the neoprene jacket/parka that fits this unit here. This will reduce your heat loss by about 200-300 watts.
Note: Out of the box this unit needs a 15amp power socket. With that said you can convert this to a 10amp compatible device in two different ways. You can either:
1. Purchase a device like an Ampfibian Mini 15amp to 10amp adaptor. If you do this you will be able to run the Digiboil, however if you turn on all three elements you will trip the circuit breaker. For this reason you will only be able to use a maximum of 2 of the elements. (not all three)
2. Alternatively you can remove the cord and replace the cord on this device with a 10amp cord, but if you do this you will need to disconnect the larger element resulting in 1300watts less power.
Digital instant read thermometer with folding probe.
A perfect pocket temperature probe for homebrewing and BBQ! Check the temperature of your mash, whirlpool additions, or use it to check the internals of that fine-looking lamb roast on the bbq! With a range of -50°C to 300°C you will be hard-pressed not to get a temperature reading.
Specifications:
- Range: -50°C ~ 300°C / -58°F ~ 572°F
- Resolution: 0.1°C
- Temperature Error: +-1°C (0~100°C)
- Power Supply: AG13 button battery x 1 (included)
Functions:
- ON/OFF
- °C/°F
- HOLD
From: Kegland
These digital scales are ideal for accurately measuring:
- Hops
- Specialty Malt
- Yeast Starters
- Coffee
- Cleaning Powders
- Disposable Cylinders
- Most items up to 10kg
Not suitable for weighing under 5g accurately.
This 10kg scale with 1gram increments scale is perfect for measuring out hop additions accurately as well as yeast for those brewers who buy in bulk, or even coffee.
Compact Size, perfect for measuring hop and yeast additions.
- Digital LED Display
- Auto Switch Off, Also with "On/Off" Button for Manual Control to Save Battery Life
- The High Precision Function Offers a Large 10000g Capacity with Precise 1g Accuracy
Package Includes:
1 x Case
2 x AA Batteries
Please note this is suited for measuring grain hops over 5g (+-3g). Not advisable for salt and water additions that require a much more accurate weight.
Electronic scales for measuring additions such as brewing salts and hops (0.1g to 1000g).
Adjusting your pH with brewing salts has never been easier than with this tiny pocket rocket scales. Flip the lid and get weighing because we wouldn't start brew day without one.
Specifications:
- Powered by 2 AAA batteries (batteries not included)
- Durable and compact digital pocket scale for easy portability
- Weighs items up to 1000 grams in 0.1 gram increments
- Easy-to-read, backlit LCD display; intuitive, flip-open lid protects the smooth, stainless-steel weighing surface
From: Kegland
A replacement dip tube (gas in) for cornelius-style kegs. Includes o-ring.
Length: approx. 40mm
A replacement liquid (long) stainless keg dip tube suitable for Kegland Corny Kegs - 19L. Can be cut down to suit 9.5L. Comes with a dip tube o-ring.
Note: there are ridges (sometimes called ears) at the top for matching post holes, which make it unsuitable for corny kegs without these matching post holes.
Looking for just the o-ring? You'll find it here.
Duotight - 6.5mm (1/4") x 8mm (5/16") Reducer.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
Duotight - 8mm (5/16') Female x 1/4' Male Thread Bulkhead (suits 60cm Thermowell).
Currently the Gen3 model.
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them. The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings. This makes these fittings even more reliable and reduces the chance of a leak significantly.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi
Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.
What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.
EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.
From: Kegland
Duotight - 8mm Female - 5-Way Multi-Tee
This particular Duotight tee saves on space and purchasing multiple generic equal tee's when setting up a 4-tap kegerator, or if you simply want to plumb up to four liquid or gas lines from one source.
Simply plumb your gas line in to any of the connections, then split it off to up to four different lines. If you want to cap off certain lines, we would recommend using an 8mm plug.
Flush mountable!
Looking for high quality push-in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Why do we use double o-rings?
The secret to the superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double o-ring means we literally have twice the sealing surface when compared with other push in fittings. This makes Duotight fittings even more reliable and reduces the chance of a leak significantly.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes Duotight fittings the most reliable push fit fittings on the market.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.
EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA-free and is the number one choice for many long-lasting food-grade applications.
From: Kegland
Duotight 8mm OD retaining circlip, suits any Duotight 8mm fitting. When clipped into place, this circlip prevents the collar of the Duotight fitting from being pushed inwards, making it impossible for the fitting to release its grip on any hose!
Note: Duotight fittings, ball lock disconnects and hose sold seperately.
From: Kegland
Duotight - 8mm (5/16') Plug
This fitting is used for gas or liquid leak testing purposes with Duotight manifolds or fittings.
Use it instead of attaching hosing to a disconnect which has other leak spot potential.
Suitable for 8mm Duotight fittings.
It is particularly useful for testing MK5 regulators and ball lock disconnects without the need for hosing and more valves.
From: Kegland
Duotight - 8mm x 9.5mm Reducer.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
Duotight - 9.5mm (3/8") Female x 1/2" Female Thread.
It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
Note: colour may vary.
From: Kegland
Duotight - 9.5mm (3/8”) Female x ½" Male Thread Ball Valve.
It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
Note: colour may vary.
From: Kegland
Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread.
It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
Note: colour may vary.
From: Kegland
Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread Bulkhead (suits TempTwister).
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them. The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings. This makes these fittings even more reliable and reduces the chance of a leak significantly.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi
Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.
What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.
EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.
From: Kegland
Duotight - 9.5mm (3/8") Check Valve (Gas).
This elbow piece is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
Due to the fact that this check valve cannot be taken apart to clean, we do not recommend it to be used with liquid.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
Compared to other push in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
The BlowTie Diaphram Spunding Valve - a great tool if you want to control the pressure retained in a pressure vessel that is releasing pressure. It has been designed for simplicity and ease of putting together. Many brewers use this spunding valve in combination with the FermZilla pressure rated fermenters.
This is the new "BlowTie 2" upgarded model which has the integrated pressure gauge. The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure. This BlowTie unit can be easily disassembled for cleaning using a screw driver. Designed to suit 8mm (5/16") tubing. It's compatible with both the 4mm ID Tubing or 5mm ID.
This compact solution for adjusting residual pressure in your fermenter makes pressure control easier than it's ever been. This can be used for compressed air, CO2, nitrogen, mains water supply and many other things but its primary use is to control the residual pressure inside fermenters.
Specifications:
1. Suits pressures 0-23psi (but with different gauges the unit can go above 100psi)
2. Made from food grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides
The design utilises the reliability of the Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.
Pressure Fermentations
With the popularity of pressurised fermentation it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.
Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg it is often a good idea to have head pressure in the keg you are filling into especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process.
Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation. Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.
The BlowTie has been made completely differently taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure.
Instructions:
Use the yellow adjustment knob to control the pressure coming out of the pressure vessel. Clockwise is higher pressure and anticlockwise is lower pressure. We would recommend gassing a keg to a known pressure e.g. 15psi then attach your BlowTie Kit to the keg and adjust to 10psi.
These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.
IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)
Material: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland
The Duotight Inline Regulator - these compact inline regulators have been designed to suit 8mm (5/16") tubing.
Suits pressures 0-150psi however this unit is packed with the 0-60psi gauge as standard. Suitable for mains water pressure, also suitable for liquid or gas.
- Made from Acetal/POM, EPDM o-rings and stainless teeth
- Suits 8mm (5/16) OD tubing
- Includes integrated 0-60psi Pressure Gauge
For higher pressures such as mains water supply we recommend the 4mm ID Tubing, or 5mm ID if you do not need as high pressures and you would prefer higher flow rate.
This compact solution for adjusting water and gas pressure can be useful in many different applications. It can be used for compressed air, CO2, nitrogen, mains water supply and many other things.
The design utilises the reliability of the Kegland patented Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.
These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.
IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)
Made From: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland
Duotight push in fitting for 8mm line to 5/8inch thread - ideal for keg couplers and tap shanks.
Duotight fittings feature a double o-ring sealing design for a more secure seal. The seals are not only high quality EPDM o-rings but also it has two of them. The double o-ring means there is literally twice the sealing surface when compared with other push in fittings. This makes Duotight fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that you can bend the hose with a much tighter radius without leaking issues.
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used for up to 100 psi.
This push in fitting will fit 8mm outer diameter tubing, while the thread on the other end will suit:
- MFL ball lock disconnects
- MKIII and MK4 regulators with MFL output
- Other fittings with MFL thread
No clamps necessary, but we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
Note: colour may vary.
From: Kegland
Duotight 8mm (5/16) one way check valve/non-return valve.
This very handy fitting could save your regulator and is a good investment. This particular type of check valve has low opening pressure of only 1 psi. It is suitable for clean liquids such as water or for gas. The spring and internal components are made with stainless steel and quality EPDM seals.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
Fits 8mm outer diameter tube.
Note: colour may vary.
From: Kegland
This Duotight Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
From: Kegland
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
Note: colour may vary.
This Duotight Push-Fit Tee - 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
Note: colour may vary.
From: Kegland
Duotight - 8mm x 1/4 inch BSP Male.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
This manifold splits one line into two, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.
If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug
Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.
The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).
Not suitable for liquids other than filtered water.
Looking for high quality push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
From: Kegland
This manifold splits one line into four, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.
If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug
Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.
The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).
Not suitable for liquids other than filtered water.
Looking for high quality push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
From: Kegland
This manifold splits one line into six, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.
If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug
Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.
The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).
Not suitable for liquids other than filtered water.
Looking for high quality push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
From: Kegland
This rigid 50mm long joiner is made from strong polypropylene. It's useful to make rigid joins with push in fittings that are dead straight. Although it's possible to make joins using short pieces of 8mm OD Evabarrier 5mm Beer Line this is far more flexible and when mounting parts to a gas board or wall its will often make things much neater if you use these instead.
The 50mm length is long enough so even after pushing right into two duotight 8mm fittings on both ends you should still have a exposed length of about 3mm so you can still relatively easily take the fittings apart later.
From: Kegland
Dimensions: 8mm OD x 6mm ID x 50mm long
