This really handy device is great for filling kegs, keg to keg transfers or fermenter to keg transfers.

Fantastic for use with Fermentasaurus or other pressurisable fermenters.

Simply attach this device to the output gas post of your Keg then when the keg is full it will prevent further liquid exiting the gas post. This means you can literally set and forget and fill kegs automatically without the risk of kegs overflowing all over the floor.

For even better results we recommend this product to be used with the Duotight - BlowTie Diaphram Spunding Valve - Adjustable PRV.  This blowtie spunding valve will also enable to to apply head pressure to the keg meaning you can control the flow speed but also reduce the foam generated in the filling process particularly for carbonated beverages like beer.

This flow stopper includes:

• 2 x duotight 8mm x 5/8 push in fittings
• 1 x ball float
• 1 x stainless spring
• 2 x straight 8mm joiners
• 1 x acrylic sight glass (with 5/8 male thread on either side)

Made exclusively for the Duotight manifolds and Gen 3.0 Duotight 8mm fittings to be mounted to a flat surface.

These can swivel around if you need to mount on a particular angle once stuck down.
They can also easily be removed from the 8mm Duotight side as they simply click/clamp in to each other.

If you are to mount this inside your Kegerator / Keezer, you must do so when the unit is off / warm. It will not stick as well in a moist / cold environment. Best to give it at least 24 hours of stick time before attaching weight / hosing to it.

Wipe down surface with isopropyl alcohol prior to sticking.

Most commonly to be used with:

• 8mm (5/16) duotight x 6 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 4 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 2 Way Manifold with Check Valves & Isolation Valves
• and duotight - 8mm (5/16) x 5 Way Multi-Tee

If you want to know if your Duotight fitting will fit this, it must be a grey Duotight that has a black collet piece.

Not suitable for 8mm ball lock disconnects
Not suitable for multiple re-applications

From: Kegland

EVABarrier Black Lightshield 4mm ID x 8mm OD - 12m Roll.

This hose is suitable for a wide range of 8mm push in fittings, either for hydroponic/gardening use or outdoor keg dispensing where UV can damage the product.

Algae will always thrive if sunlight and an exposed nutrient solution is available. That is why it is crucial to use the correct hosing when it comes to hydroponic systems and or outdoor beer dispensing systems.

Prevention is the best cause of action when it comes to algae control. EVABarrier LightShield Black should be your number one choice of hosing when setting up your indoor or outdoor growing space.
UV stable hosing that will not kink or burst under normal use.

Specifications:
4mm Internal Diameter
8mm Outer Diameter
12m Roll

EVABarrier Hosing
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings.  The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.

Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier and now with LightShield technology an excellent UV and Visible light blocking properties. The significantly better barrier properties means your beverage is better protected from oxygen and also has a better barrier to CO2 loss.  So your beer will stay fresher for longer and not lose carbonation like other beer line types.  In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period.  EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.

Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable.  This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.

From: Kegland

EVABarrier Red Lightshield 5mm ID x 8mm OD - 12m Roll

Red semi-transparent EVABarrier for kegging setups. Easily see your gas lines in minimal light without confusion.

This high quality beer line will keep your previous beverage in it's best possible condition in the process.

This 5mm size is the one of the most common sizes for kegerator setups.

When using this 5mm ID size you will need to use about 3-4 meters of beer line to get adequate flow resistance between your keg and tap for most kegerator setups.

Pressure Rating (with 1.5x safety factor)
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)

This new Red EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.

Red Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings.  The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.

Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier.  The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss.  So your beer will stay fresher for longer and not loose carbonation like other beer line types.  In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period.  EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.

Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable.  This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.

From: Kegland

This particular kit is a one-click option for those who want to be able to brew a single batch under pressure with a 27L Tri-Conical FermZilla. Designed as a single batch system that goes perfectly hand in hand with the BrewZilla 35L or Grainfather G30 if you are looking to brew All Grain or Partial Mash beers.

This is a very good starting point for those who are just getting into pressurisable fermenters and want to know what we would recommend to use with them. Pressure fermentation opens up a world of possibilities for the homebrewer wanting to take their beers to the next level. If you are kegging then the ability to do a closed pressure transfer straight into a keg is worth the cost of entry!

The new stock standard includes:
1 x FermZilla Easy-Grip Threaded Lid Ring
1 x Integrated Gauge BlowTie Kit (0-15psi) Spunding Valve
1 x 100cm Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float
1 x Yellow Liquid Carbonation Caps
1 x Red Gas Carbonation Caps
1 x FermZilla Pressure Lid
1 x Red 35psi / 2.5BAR Pressure Relief Safety Valve
1 x FermZilla - Graduation Sticker 27L
1 x Strip Stick On Thermometer
1 x 27L FermZilla Tri-Conical Tank
1 x FermZilla - Conical Stainless Stand
1 x 3 Inch TC Beaded Seal - Silicone
1 x 3 Inch TC Clamp - 3 Segments
1 x 3 Inch TC x 3 Inch TC FermZilla Butterfly Valve Assembly
1 x FermZilla - 3 Inch Tri-Conical - 600ml Collection Container Kit

*Please note: none of these can be changed, substituted or swapped out* If you want something different to the above, please order it separately.

This kit has carbonation caps on the collection container either to purge or take samples of yeast from. You may need additional keg connectors and line for this, and for transfers.

We would also still recommend getting a CO2 Gas to be able to transfer to a keg/bottle/can or dispense directly out of the unit. As these units were designed to be fermenting and pressure transfer vessels for your delicious cargo.

What's new: the difference between Gen2 and Gen3?

1. Moulded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch Tri-Clamp Butterfly Valve
3. 3 Inch Tri-Clamp 600mL Collection Container
4. The latest models now come with an Easy-Grip Threaded Lid Ring that has a multitude of uses.

The new and improved FermZilla 27L brought to you by the critical key minds and engineers behind the original Gen1 and Gen2. But with all the tweaks that make it the most cost-effective conical fermenter to date!

The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget. With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.
This is an incredible product at an extremely attractive price point in all the different sizes and models.

Please note:

When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage.

Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.

Product Downloads
Instruction Manual
Dimensions

FermZilla 27L Tri-Conical Starter Kit - Generation 3.2

Introducing the Gen3 FermZilla Tri-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and a 600mL collection container with a 3 Inch Tri-clover connection, the gold standard for sanitary design and effortless removal. No more complicated dump valve designs here, just simplicity. Brew with confidence on the new Tri-Clover FermZilla Range.

The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget. With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.

This is an incredible product at an extremely attractive price point in all the different sizes and models.

The FermZilla 27L Tri-Conical can be used in the following ways:

• Basic Gravity Fermenter - New Brewers
• Pressure Brewing Kit - Most Popular
• Hop Bong Pressure Kit - For Intermediate Brewers
• Glycol Twister Pressure Brewing Kit - Glycol Obsessed

What's new the difference between Gen2 and Gen3?
1. Moulded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch tri-clamp butterfly valve
3. 3 Inch tri-clamp 600mL collection container

Is it easier to clean / take apart than the Gen2?
YES, It is by far the easiest Conical PET fermenter to disassemble and clean into all the nooks and crannies. Simply release all pressure inside the vessel and detatch the tri clover clamps.

What does the starter kit come with?
      1 x 27L Conical FermZilla Tri-Conical Base Kit (unassembled)
      1 x 27L Gen3 Tri-Conical Tank with metal neck ring
      1 x Standard Top Lid, with Red PRV (35psi) [2 x Male PCO1881 Cap Threads] [Up to 4 drill ports for accessories]
      1 x Collar Lid Ring
      1 x Grommet PCO1881 Black Cap + 1 x Blank PCO1881 Black Cap for lid
      1 x Premium 3 Piece Airlock
      1 x 3 inch tri-clamp to 3 inch tri-clamp butterfly valve
      1 x 600mL Collection Container & Lid* [2 x Male Cap Threads]
      2 x Blank PCO1881 Black Cap
      1 x 3 piece ~ 3 inch tri clover clamp [+ 1 x 3" Beaded Silicone Seal]
      1 x 2 piece ~ 2 inch tri clover clamp [+ 1 x 2" Beaded Silicone Seal]
      1 x Stainless Stand with swing handles
      1 x Stainless Steel Handle Assembly
      1 x Strip Stick On Thermometer
      1 x Level indicator sticker (Litres and Gallons)
      1 x Spare Lid O-Ring
      1 x Spare Collection Container O-Ring

Instructions:
To download the instruction sheet for this product click on the link below:
FermZilla 27L - Tri-Conical PDF Instruction Manual

Dimensions:

To download the dimensioned drawings for this product click on the link below:
FermZilla 27L Tri-Conical Dimensioned Drawing

Warnings:
Please read the instructions thoroughly before use.

• We will not be held liable for misuse or mishandling of the unit contrary to the instructions.
• Keeping the units out of direct sunlight is a must for all PET fermenters. Sunlight degrades PET.
• Do not expose to temperatures exceeding 35°C and pressure ferment past 5psi at these temperatures.

Please note:
When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage. 

Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.

Help Stabilize Your Fermentation Temperatures with the FermZilla Insulating Jacket
Fits both FermZilla 27L Conical and All Rounder 60L

Give your fermenter practical temperature support! Kegland’s insulating jacket easily zips over your 27L Conical or 60L All Rounder, creating a protective thermal layer to reduce ambient temperature swings. Use it standalone or supercharge your control with these active solutions:

How It Works:

Reduces Temperature Fluctuations: Minimises impact from room temperature changes
Active Heating: Pair with a RAPT Temperature Controller + Heating Wrap
Active Cooling: Use with Temp Twister Coil + Pump Kit
Passive Cooling: Place frozen water bottles between jacket and fermenter
Full Coverage Design: Light-blocking insulation with lid access

Compatibility:
→ FermZilla 27L Conical (Gen 3)
→ All Rounder 60L

Your Complete Thermal System:
Maximize control with these setups:
→ Basic: Jacket alone (reduces fluctuations)
→ Pro Heating: Jacket + RAPT Controller + Heating Wrap
→ Pro Cooling: Jacket + Temp Twister Coil + Pump Kit
→ DIY Cooling: Jacket + frozen bottles

Complete Your Temperature Control Kit:
Heating Solutions:

• RAPT Temperature Controller

• 30W Heating Wrap

Cooling Solutions:

• Temp Twister Cooling/Heating Coil

• Temp Twister Pump Kit

This collection container fits all the FermZilla Tri-Conical fermenters that have a 3 inch x 3 inch butterfly valve. No more threads or removal tools to get this off, simply depressurise and remove the tri-clamp fitting. We'd recommend placing a towel or upside down frisby to catch some drips.

The clear body is made from Tritan from Eastman Plastics.  This heat tolerant plastic is BPA, and plasticiser free.

The ports on the side of this collection container are the same as a standard coke bottle or soft drink bottle.  These are also the same on the top of the FermZilla.
We would recommend using the following two items (not included) on your collection container for the average user:
1 x Red Ball Lock Plastic Carbonation Cap x 6.35mm duotight
1 x PCO1881 Gas Pressure Relief Valve Cap (PRV) and Pressure Relief Valve 35PSI (Red)


Includes:
1 x 600mL Tritan plastic collection container with 3" tri-clamp ferrule and 2 x Vertical PCO1881 Carbonation Cap Ports
1 x 3" tri-clamp clamp (3-Piece)
1 x 3" tri-clamp beaded seal
1 x 3" tri-clamp black POK end cap

Dimensions:
170mm High
Tapered from 3 Inch tri-clamp down to 66mm

From: Kegland

This particular kit is a one-click option for those who want to be able to brew a double batch under pressure with a 55L Tri-Conical FermZilla. Designed as a single batch system that goes perfectly hand in hand with the BrewZilla 65L if you are looking to Brew All Grain or Partial Mash beers.

This is a very good starting point for those who are just getting into pressurisable fermenters and want to know what we would recommend to use with them. Pressure fermentation opens up a world of possibilities for the homebrewer wanting to take their beers to the next level. If you are kegging then the ability to do a closed pressure transfer straight into a keg is worth the cost of entry!

The new stock standard includes:
1 x FermZilla Easy-Grip Threaded Lid Ring
1 x Integrated Gauge BlowTie Kit (0-15psi) Spunding Valve
1 x 100cm Silicone Dip Tube Kit with Yellow Weighted Filter and SS Float
1 x Yellow Liquid Carbonation Caps
1 x Red Gas Carbonation Caps
1 x FermZilla Pressure Lid
1 x Red 35psi / 2.5BAR Pressure Relief Safety Valve
1 x FermZilla - Graduation Sticker 55L
1 x Strip Stick On Thermometer
1 x 55L FermZilla Tri-Conical Tank
1 x FermZilla - Conical Stainless Stand
1 x 3 Inch TC Beaded Seal - Silicone
1 x 3 Inch TC Clamp - 3 Segments
1 x 3 Inch TC x 3 Inch TC FermZilla Butterfly Valve Assembly
1 x FermZilla - 3 Inch Tri-Conical - 600ml Collection Container Kit

*Please note: none of these can be changed, substituted or swapped out* If you want something different to the above, order it separately.

This kit has carbonation caps on the collection container either to purge or take samples of yeast from. You may need additional keg connectors and line for this, and for transfers.

We would also still recommend getting a CO2 gas bottle to be able to transfer to a keg/bottle/can or dispense directly out of the unit. As these units were designed to be fermenting and pressure transfer vessels for your delicious cargo.

What's new; the difference between Gen2 and Gen3?

1. Moulded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch Tri-Clamp Butterfly Valve
3. 3 Inch Tri-Clamp 600mL Collection Container
4. The latest models now come with an Easy-Grip Threaded Lid Ring that has a multitude of uses.

The new and improved FermZilla 55L brought to you by the critical key minds and engineers behind the original Gen1 and Gen2. But with all the tweaks that make it the most cost-effective conical fermenter to date!

The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget. With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.
This is an incredible product at an extremely attractive price point in all the different sizes and models.

Please note:

When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage.

Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.

Product Downloads
Gen3 FermZilla Tri-Conical User Guide
Hydro Test Guide

FermZilla 55L Tri-Conical Starter Kit - Generation 3.0

Introducing the Gen3 FermZilla Tri-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and redesigned tri-clover dump valve. This unit was born from customer feedback we received on the Gen2 Model. No more complicated dump valve designs here, just simplicity. Brew with confidence on the new Tri-Clamp FermZilla Range.

The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget.  With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.
This is an incredible product at an extremely attractive price point in all the different sizes and models.

The FermZilla 55L Tri-Conical can be used in the following ways:

• Basic Gravity Fermenter - New Brewers
• Pressure Brewing Kit - Most Popular
• Hop Bong Pressure Kit - For Intermediate Brewers
• Glycol Twister Pressure Brewing Kit - Glycol Obsessed

What's new the difference between Gen2 and Gen3?
1. Molded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch to 2 inch tri-clamp Butterfly Valve
3. 2 inch tri-clamp compatible Collection Container

Is it easier to clean / take apart than the Gen2?
YES, It is by far the easiest Conical PET fermenter to disassemble and clean into all the nooks and crannies. Simply release all pressure inside the vessel and detatch the tri clover clamps.

What does the starter kit come with?
      1 x 55L Conical FermZilla Tri-Conical Base Kit (unassembled)
      1 x 55L Gen 3 Tri-Conical Tank with metal neck ring
      1 x Standard Top Lid, with Red PRV (35psi) [2 x Male PCO1881 Cap Threads] [Up to 4 drill ports for accessories]
      1 x Collar Lid Ring
      1 x Grommet PCO1881 Black Cap + 1 x Blank PCO1881 Black Cap for lid
      1 x Premium 3 Piece Airlock
      1 x 3 inch tri clover to 2 inch tri clover Butterfly Valve
      1 x 1000mL Collection Container & Lid* [2 x Male Cap Threads]
      2 x Blank PCO1881 Black Cap
      1 x Brewbuilt Flex Container lid with 2 inch tri-clover ferrule.
      1 x 3 piece ~ 3 inch tri clover clamp [+ 1 x 3" Beaded Silicone Seal]
      1 x 2 piece ~ 2 inch tri clover clamp [+ 1 x 2" Beaded Silicone Seal]
      1 x Stainless Stand with swing handles
      1 x Stainless Steel Handle Assembly
      1 x Strip Stick On Thermometer
      1 x Level indicator sticker (Litres and Gallons)
      1 x Spare Lid O-Ring
      1 x Spare Collection Container O-Ring

Instructions:
To download the instruction sheet for this product click on the link below:
FermZilla 55L - Tri-Conical PDF Instruction Manual

Dimensions:

To download the dimensioned drawings for this product click on the link below:
FermZilla 55L Tri-Conical Dimensioned Drawing

Warnings:
Please read the instructions thoroughly before use.

• The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.
• Keeping the units out of direct sunlight is a must for all PET fermenters. Sunlight degrades PET.
• Do not expose to temperatures exceeding 35°C and pressure ferment past 5psi at these temperatures.
  

Please note:
When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage. 

Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.

From: Kegland

The FermZilla All Rounder 30L is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. It's far more capable than the FermZilla Flat bottom but it's less complicated and less expensive than the FermZilla Conical Unitank. So like the name says it's the "All Rounder".

If you want to use this product under pressure we would recommend that you use the pressure kit.

This kit includes:

• 1 x All rounder tank
• 1 x Stainless Steel Handle Assembly
• 1 x 304 stainless stand
• 1 x Airlock
• 1 x Pressure rated lid
• 1 x Digital temperature sticker
• 1 x Red 2.5bar pressure relief valve
• 1 x Graduation Sticker

Easy to Clean

This fermenter is made from super smooth PET so it's easy to clean. Just use a small scoop of PBW or similar and wipe it clean after a 5 minute soak. No scrubbing necessary.

Large 120mm Opening

The opening at the top is significantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.

Pressure Rated

This fermenter is rated up to 2.5bar so you can force carbonate just like a keg. You can use this fermenter for closed transfers and significantly reduce oxygen exposure.

Crystal Clear

The wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is flocculating etc.

Impermeable

The PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.

No Flavour and Aroma Carry Over

Other HDPE fermenters tend to be so porous they carry flavour and aroma from one batch to another.

Robust and Difficult to Damage

Impossible to smash like glass. The tank is impact resistant but light weight and easy to use.

IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also, while this tank comes pressure tested we recommend that every 2 years you re-hydro test this tank yourself.

From: Kegland
Diameter: approx. 352mm
Height: approx. 569mm (from stand base to top of airlock) or 614mm with stand reversed

The FermZilla All Rounder 60L is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. It's far more capable than the FermZilla Flat bottom but it's less complicated and less expensive than the FermZilla Conical Unitank. So like the name says it's the "All Rounder".

If you want to use this product under pressure we would recommend that you use the pressure kit.

This kit includes:

1 x All rounder tank
1 x Stainless Steel Handle Assembly.
1 x 304 stainless stand
1 x Airlock
1 x Pressure rated lid
1 x Digital temperature sticker
1 x Red 2.5bar pressure relief valve
1 x Graduation Sticker

Easy to Clean
This fermenter is made from super smooth PET so it's easy to clean.  Just use a small scoop of PBW or similar and wipe it clean after a 5 minute soak.  No scrubbing necessary.

Large 120mm Opening
The opening at the top is significantly larger then the older Snub Nose or other pressure fermenters.  This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.

Pressure Rated
This fermenter is rated up to 2.5bar so you can force carbonate just like a keg.  You can use this fermenter for closed transfers and significantly reduce oxygen exposure.

Crystal Clear
The wall of the All Rounder is crystal clear so you can see what's going on inside.  This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.

Impermeable
The PET plastic is not permeable like some other fermenters made from PP or HDPE.  The fermenter wall is a much better gas barrier keeping your product fresher for longer.

No Flavour and Aroma Carry Over
Other HDPE fermenters tend to be so porous they carry flavour and aroma from one batch to another. 

Robust and Difficult to Damage
Impossible to smash like glass.  The tank is impact resistant but light weight and easy to use.

Please read the instructions thoroughly before use. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.

IMPORTANT NOTE: This tank should not be used for hot liquid.  Do not put liquids inside this tank over 50C.  It will melt the tank.  Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself.  

Note: Some of the photos are of the FermZilla - All Rounder 60L with a red plastic pressure kit. The pressure kit is not included in the standard kit.

From: Kegland

This handy little strap will make cleaning and transport your FermZilla All Rounder 30L or 60L an absolute breeze. Simply attach through both sections of the base in the orientation you wish. Slide up and out of the little buckle pieces making sure that the buckle is facing towards you, then strap in and strap down!

The Strap is long enough for the 60L and 30L. We recommend rolling up the excess strap and paper clipping or cutting to suit the 30L. 

Please note the paper clips used in the photos are not included.

From: Kegland

This jacket is designed to insulate your FermZilla 55L fermenter during the colder months to keep your fermentation at the optimum temperature. It can also be used with a heater belt to warm up the wort if the heat from the fermentation isn't enough. It also completely blocks any light/UV to prevent light stuck beer.

From: Kegland

A replacement FermZilla lid, made from glass reinforced engineering plastics that are not only chemical resistant, heat resistant but also tough as nails so they will last you a lifetime.

This lid is made from high quality plastic and will suit any of the FermZilla fermenters, uni tanks, bright tanks. It will suit:

FermZilla 27L - Conical Fermenter
FermZilla 35L - Conical Fermenter
FermZilla 55L - Conical Fermenter
FermZilla 27L - Flat Bottom
FermZilla 55L - Flat Bottom
FermZilla 27L - Bright Tank
FermZilla 55L - Bright Tank

Note: does not include the FermZilla lid ring that holds this down

From: Kegland

FermZilla - Replacement Lid Seal (OD 106mm x 2.65mm).

This thicker Lid O-Ring is suited to FermZilla Conical and All Rounder Models. 

If you have a brown O-Ring, this is a newer material that is softer and easier to fit. All units manufactured after 01/01/2023 will have this Brown O-Ring as standard

If you are experiencing leaking from the top lid section, this slightly thicker O-Ring will aid in resolving said leaking. To perform a leak test please remember to have the unit free of any liquid as that will absorb CO2.

It is also important to remember not to overtighten the stainless steel handles that may have come with your FermZilla. Overtightening will cause the opening to warp and not seal. The handles should be able to freely rotate around the neck with little resistance.

Note: this is for the seal only, lid not included.

From: Kegland

This jacket will keep your FermZilla All Rounder 30L cool in summer and warm in winter. It can also be used with a heater belt to warm up the wort if the heat from the fermentation isn't enough. To control the temperature, we suggest using a MKII Temp Controller.

This jacket also completely blocks any light/UV to prevent light struck or skunked beer.

From: Kegland

New FermZilla lid ring is a must in your home brewery! 

The Fermzilla Easy-Grip Threaded Lid Ring is the Swiss army knife you need in your fermenting space! This isn't any normal lid ring, this beast is built to be a fermzilla socket set!

Features:

Underside Hex holes
Use these to undo or tighten plastic carbonation caps on your fermzilla lid!

Ergonomic Handles
More leverage to easily undo the threaded lid ring! Comfortable to lift and move the fermenter.

Handy Hook
No need to use one hand or place the lid in sanitiser for pitching yeast or dryhopping. Simply use the hook to latch the lid onto the fermzilla opening. Now you have two free hands to work with!

Dry hop or pitch yeast with ease!

Carbonation Post hole
Easily pop stubborn lids out using leverage.

Fits both sizes of All Rounder and both sizes of Tri-Conical:
30L FermZilla All Rounder 
60L FermZilla All Rounder
Gen3 27L FermZilla Tri-Conical
Gen3 55L FermZilla Tri-Conical

Works with both the regular flat lid and TC lid:
FermZilla - Replacement Pressure Lid (NO RED PRV) - Suits Conical and All Rounder
FermZilla - 2 Inch TC Pressure Lid Kit

From: Kegland

FermZilla Plastic Pressure Kit - suits both 27L and 55L FermZilla fermenters. This is the plastic version, there is also a stainless option.

Add this optional pressure kit to your FermZilla and turn your FermZilla into a true unitank. Unitanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. This extremely inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:

Fermenting Under Pressure: First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also a good idea to have two relief valves on the FermZilla anytime the unit is under pressure.

Carbonating, Pushing, and Serving: When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.

Lack of Oxidation Because the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.

Key Features:

• Ferment beer under pressure to reduce ester and fusel alcohol production
• Ability to always draw clear beer with the unique, floating draw tube
• Keg already carbonated beer
• Use co2 to push beer into a keg or though a filter into a keg
• Carbonate and serve beer directly from the FermZilla, eliminating kegging all together

Kit Includes:

1 x Red Plastic Carbonation Cap
1 x Yellow Plastic Carbonation Cap
1 x Float & Dip Tube Filter Kit

Add the optional pressure kit to your FermZilla and turn your FermZilla into a true uni tank. 

Uni tanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. 

Here are some possibilities:

Fermenting Under Pressure:

First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. 

Carbonating, Pushing, and Serving:

When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever.  You can also choose to send carbonated beer through a beer filter on the way to your keg.  When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.  

Lack of Oxidation

Because the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.  

Key Features:

•    Ferment beer under pressure to reduce ester and fusel alcohol production

•    Ability to always draw clear beer with the unique, floating draw tube  

•    Keg already carbonated beer

•    Use co2 to push beer into a keg or though a filter into a keg

•    Carbonate and serve beer directly from the FermZilla, eliminating kegging all together

The Temp Twister allows you to heat and cool your FermZilla or other fermenter or bright tank, ideally by combining with a glycol chiller. This coil can be adapted to fit any fermenter or bright tank that has an opening of 110mm diameter or larger. Simply drill to two 22mm holes in the lid of your fermenter and use the included Duotight bulkhead fittings to attach the coil to the lid of your fermenter. 

Specifications

• Coil Diameter x Height: 11cm x 68cm
• High Material: 304 Stainless Steel Coil
• Thickness: 9.5mm OD (3/8")
• Coil Length: 6 meters
• Heat Transfer: With this coil submersed in liquid it will be able to absorb more than 250watts

From: Kegland

FermZilla Temp Twister Lid - predrilled and including o-ring.

Take the pain and risk away from drilling your own Temp Twister Ports and Thermowell for your FermZilla. We've done the tricky work for you!

Does not include
1 x Red Gas Carbonation Cap
1 x Yellow Carbonation Cap
1 x Red 35psi OR 17psi Yellow Pressure Relief Valve (safety device)
1 x 60cm Thermowell Kit
1 x Temp Twister
1 x G20 Pump Up or G40 Pump Up/
1 x FermZilla All Rounder or Conical

Suits:
60L All Rounder FermZilla
55L Conical FermZilla
30L All Rounder FermZilla
30L Flat Bottom FermZilla (Not pressure rated)
27L Conical FermZilla

From: Kegland

A 10 inch filter housing for filtering your beer prior to bottling or kegging, or to filter water.

For beer this filter works best when used when transferring cold uncarbonated beer. All you will need to do is purchase some hosing, clamps, ball locks (if transferring to or between kegs) and a 1 Micron Filter to use this system.

- Clear high pressure housing
- Purge valve to expel air pockets
- ½” BSP inlet and outlet
- Includes Duotight 9.5mm (3/8"") fittings 
- Brass threaded ports for durability
- Compatible with other 10” filter systems

Note: you will need tubing to match the fittings (not included).

You will need a filter insert to use this system, like our 1 Micron Washable Filter (for filtering beer) or a 0.5 Micron Carbon Water Filter, (for water filtering).

Not suitable for hot liquids.

A rugged and durable push fit, inline filter strainer. 

Available in both 8mm and 10mm push fit size.

The detachable cap and body allow for easy servicing and cleaning.

Do not apply excessive vibration, torque, shock or other strong loads to the filter as the filter body may damage or collets may be dislocated.

Filter grade: 100 mesh
Colour: Black
Max. Pressure: 170psi
Temperature: Air -20C, Liquid 65C
Height: approx. 70mm

FermZilla - SS Ball Float & 80cm Silicone Dip Tube and Filter Kit. Suits Tri-Conical and All Rounder Models.

This simple design allows you to extract the clearest possible liquid in your pressure vessel with the added security of our new filter included. This helps prevent blockages in your carbonation cap poppet. As the liquid level decreases the float goes down at the same time. Perfect for sampling the sediment free!

This 80cm silicone dip tube and stainless steel float with filter suits the FermZilla Tri-Conical fermenter. Also compatible with Kegmenters and Modified Ball Lock Kegs (not minikegs).

From: Kegland

This simple design allows you to extract the clearest possible liquid in your pressure vessel with the added security of our new filter included. This helps prevent blockages in your carbonation cap poppet. As the liquid level decreases the float goes down at the same time. Perfect for sampling the sediment free!

The new yellow cap is weighted to approximately 10g! Making it sink just that little bit lower to gain more liquid and less likely to suck air.

This 100cm silicone dip tube and stainless steel float with filter suits:
- FermZilla Tri-Conical 27L
- FermZilla Tri-Conical 55L
- FermZilla All Rounder 30L
- FermZilla All Rounder 60L
Also Compatible with Kegmenters, 50L Kegs and Modified Ball Lock Kegs (not minikegs).

From: Kegland

The Gas Ball Lock Post for Keg Coupler is a liquid ball lock post with a female 5/8 inch connection. It allows you to connect ball lock disconnects to a keg coupler making it extremely easy to swap over from a corney keg to a commercial keg (you will need the correct coupler for the keg as well). 

Gas Free Ball Lock Line Cleaning Kit

Are you ever in a situation where you don't want to unhook your gas line from your kegs, or have ball lock disconnects that you need to clean over at the sink but don't want to take your gas line all the way over there? Well, Kegland thought of a better way. Why not fill a PET Bottle with your cleaner / sanitiser and pump it without gas!

This little device can also be used as a mini party keg without a gas source (should be consumed well within 24 hours of pumping). BYO Liquid disconnect, hose and picnic tap.

Contains:
1 x KegLand Yellow Carbonation Cap
1 x KegLand PCO Tee Piece (Female x Male x Male)
1 x Mini Yellow Hand Pump
1 x 30cm Piece of EVABarrier Line 5mm ID x 8mm OD (can be stretched for larger PET bottles)

From: Kegland

The MaltMuncher 2 Roller Grain Mill, featuring cold steel rollers with aluminium chassis. This Malt Muncher is adjustable to get your grain bill crushed exactly the way you want it. 10mm crank shaft as standard, perfect for the entry level millers wanting to use a drill to keep rolling.

Or if you want a work out and look like a pro arm wrestling champion, a manual crank comes as standard just to get you going.

If you are going to be using a drill, don't go crazy with speed, you can risk cooking/burning your grain and impeding the mills performance. If at all possible just enough power to get it going and catching. This should fall around the 200rpm mark.

Includes:
- Grain hopper (2.7kg capacity)
- Manual Crank handle
- 10mm crank shaft
- Roller adjustment knobs
- Reinforced chassis with pre aligned mounting holes for perfect stability if mounting to a board.
- 12 TPI knurl to efficiently pull grain through rollers while leaving hull intact to form an excellent filter bed for sparging

Comes flat-packed and requires assembly.

Note: does not include base board.

We also have the 3 Roller model.

From: Kegland

Convert the Recirculation Arm and the Counter Flow Chiller of the Grainfather to convenient Camlock fittings.

This upgrade kit consists of 5 stainless steel parts to convert the Grainfather Recirculation Arm and Wort Chiller to easy to use Camlock fittings.

Watch David Heath's YouTube video above for more information and installation instructions.

Click here for an installation guide.

Kit contains:

• BSP Hex/Reducing Bush 1/2 Inch - 3/8 Inch
  
• Camlock - Female to 1/2 Inch Female D Type
• Camlock - Male to 1/2 Inch Female A Type
• Camlock - Male to 1/2 Inch Barb E Type
• Compression Fitting - 12.7mm to 1/2 Inch BSP

Please measure the diameter of your Grainfather Recirculation Arm to ensure the compression fitting will fit.

Master Your Brew, Wine, or Spirit Wash with Precision Heat Control.

Temperature dictates fermentation success. Too cold, and you risk sluggish, stuck ferments. Too warm, and you invite excess esters, fusel alcohols, and VDKs—compounds that compromise a clean flavour profile. This applies equally to beer, wine, and distilled spirits.

The Handcraft Supplies Adjustable Heat Belt solves both extremes. It provides gentle, consistent warmth to your fermenter, but with a unique mechanical twist: Lower the belt to increase heat; raise it to decrease heat. This lets you actively manage the exothermic peak of fermentation, preventing overheating while ensuring your yeast finishes strong.

• Universal Fit: Carboys, buckets, and stainless steel units.

• Strain-Specific Control: Easily maintain the right temperature for the yeast you are using (e.g.: 18–22°C for ales, 8–15°C for lagers, 15–20°C for white wines, 20–25°C for red wines, and 25–30°C for rum or whisky washes.

• Simple & Safe: Low-wattage, secure tightening design.

While this heat belt is ideal for beer, it is equally valuable for wine and spirits production. Wine ferments thrive on stable temperatures to preserve delicate fruit esters and prevent volatile acidity, while spirit washes—particularly for rum and whiskey—often require warmer conditions to maximise yeast attenuation and develop desired flavour precursors. For ultimate precision across any ferment, pair your heat belt with a temperature controller such as a Rapt Temperature Controller or MKII Temperature Controller. This automates the heating cycle, holding your wash, must, or ber within a fraction of a degree of your target. For the most accurate reading, tape the probe directly to your vessel (insulated from ambient air) or use a thermowell to monitor the true core temperature—ensuring professional-grade consistency whether you are brewing beer, fermenting wine, or making spirits.

Brew smarter, not harder. Get your Handcraft Supplies heat belt today.

A brewing heater belt that fits around your fermenter to provide steady and constant warmth for your brew. The 30 watts will gently warm without creating a hot spot, and can be moved up or down the fermenter to increase or decrease the heat transfer to the brew.

To further control the temperature of your fermentation, combine with a RAPT Temperature Controller or similar to regulate the heater belt automatically.

Note: fermenter not included.

From: Kegland

These 304 Stainless 2200w weldless elements are designed to fit a 32mm hole inside the wall of your brewing vessel or boiler. It comes bundled with the power cord.

We do recommend using a RAPT Temperature Controller to run this element with the appropriate thermowell or temperature probe attachment.

These electric brewing elements are highly recommended for your HLT, or even for a HERMS or RIMS setup. Multiple elements may be required for larger volumes and depending on what temperature you are trying to achieve. If you are going to be using these elements directly in your mash tun, and will try to maintain temperature using the element, we would recommend getting a power control chip 3600w to modify the power output to the element. Too higher power directly in contact with your malted grain can cause scorching/off flavours as the temperature may not be evenly distributed and isolated purely around the element itself.

Element Length: approx. 300mm
Diameter: approx. 25mm
Thread: approx. 32mm
From: Kegland