Sort by:
3600 Watt Stainless Steel Heating Element with 2 inch tri-clamp (220-240v)
It can be fitted to a 2" tri-clamp ferrule. It does have a water-resistant screw element guard. This was produced to be used with the 118L Kegmenter that has 2" ferrules.
It is highly regarded as a popular and reliable element for distillers and homebrewers.
This element is to be installed by a professional electrician with a 15amp Cord.
From: Kegland
Fermentation Heating Wrap Belt - With Velcro Strap (30watts) 220-240VAC (50-60hz)
Perfect heating solution for those who want more even coverage and absolute certainty that their PET fermenter will not melt even if the fermenter is empty.
Punching in at an ample 30 watts, this heating wrap belt is great when paired with insulation and a temperature controller box to dial in that optimum fermentation profile.
To further control the temperature of your fermentation, combine with a RAPT Temperature Controller or similar to regulate the Heating Wrap Belt automatically.
Features:
- Easy to use
- Handy velcro strap
- Low watt density
- Durable vinyl coating
- 30 watt gentle heating
- Great for fermenters or bottle conditioning
- Sit on top or wrap around your fermentation vessel
Dimensions: approx. 1000mm x 250mm
From: Kegland
This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla.
It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel.
Diameter: approx. 66mm Heigh: approx. 300 mm.
From: Kegland
Hoses play a huge role in draft beer dispensing. They carry gas from the tank to the coupler and beer from the keg right up to the faucet. These pipes are of soft, flexible but durable material. They are usually of Vinyl and Polypropylene. The hoses are also part of glycol pythons.
Hoses are connected through adapters and barbs to form the entire dispensing system. The length really depends on how far your serving point is from the keg. You might have to shorten or cut out from a large bundle. For any of this, you require a Hose and Tubing Cutter.
This cutter is sturdy and sharp that cuts right through the hose in a jiffy without leaving any rough edges too.
- Material: Plastic
- Finish: Raw
- Color: Black
Looking for a smaller option, you'll find one here.
From: Krome Dispense
A tool for cutting hose and tube, with a stainless steel blade.
From: Krome Dispense
A hydrometer is an essential tool for testing starting and finishing gravity, or sugar content, in beer or wine or spirit fermentations. This is a triple scale hydrometer - specific gravity, potential alcohol and approx. sugar per litre.
Best used with a trial jar (sold separately).
Handcraft Supplies Triple Scale Fermentation Hydrometer measures the specific gravity, potential alcohol, and approx. sugar content of any fermentable liquid, whether you're making wine, cider, beer, or distilling wash.
Best used with a trial jar (sold separately).
Infrared Thermometer Gun -50C to +580C (Black)
This thermometer gun has a built-in Dual laser that can be switched On and Off. Dual laser is an important feature when choosing infrared thermometers because it allows for much higher accuracy of readings. When measuring an object a Dual Laser will help greatly in finding the convergence point of the measured target and the spot ratio, which can only be achieved with Dual Laser.
Features:
- Double Laser pointer for accurate target aiming
- Simple one-handed operation
- Laser ON/OFF Switch
- Low battery indication
- LED backlight system for operation under poor illumination
- C° / °F temperature unit conversion
- Automatic Power off in 15 seconds without any operation
- Display hold, scan function
Note:
1. When using this product to measure temperature, consider the ratio between the distance (the length from the product to the measured object) and the size of the measurement area, referred to as the object distance ratio. When the distance between the product and the measured object increases, the measurement area will increase accordingly.
2. If you want to use boiled water to measure the quality of the product, please note that when measuring boiling liquids, do not allow smoke or water vapour to contact the temperature sensing area, and keep the measurement angle at 45 ~ 60 degrees.
Specifications:
- Temperature Range: -50 to 550°C
- Accuracy: ± 2% or 2°C
- Distance Spot Ratio: 12:1
- Emissivity: 0.1~1.0(Adjustable)
- Response Time Wavelength: 500ms & (8-14) um
- Repeatability: ± 1% or 1°C
- Resolution: 1°C or 1°F
- Storage Temperature: -20-50°C
- Operating Temperature: 0-50°C
From: Kegland
This unit has been designed to fit Kegland standard Single, Double and Triple Tap Kegland Kegerator Towers or any other 76mm diameter font.
Keep your beer icy-cold with this insulated tower/font cover right out of the first drop. Most kegerators that we sell include a font fan that blows cold fridge air up the font. With that said heat loss from the stainless font surface causes the font temperature to rise meaning that a small amount of beer contributes to the "first pour foam effect".
These extra thick covers are made from 7mm neoprene, meaning your beer will stay cold even if the hot sun is beating down directly on the font.
This helps save power as your fridge will not be working as hard, and you pay less in power. So this thing practically pays for itself!
How to Install
1. Remove taps from the font. (no need to remove the shank from the font, just the taps).
2. Pull the insulated cooler down over the font.
3. Mark the tap holes and use a sharp pair of scissors to cut a hole in the neoprene jacket.
4. Re-attach the taps.
NOTE: Nail cutting scissors are particularly good for this application, or a 5/8" Hole Punch.
Please note these only come with a Kegland logo. They are not sold in plain black.
From: Kegland
Now updated with the all new duotight 8mm Ball Lock Disconnect (Grey+Red/Gas)
This kit has been designed for simplicity and ease of putting together.
This Kit Contains:
1 x BlowTie Spunding Valve Gen 2 with 0-15psi Integrated Gauge
1 x Duotight 8mm (5/16") x Ball Lock Disconnect (Grey+ Red/Gas)
1 x Rigid 8mm Plastic Joiner
All new compact BlowTie Spunding Valve Gen2 Integrated Kit. If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job.
If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job.
The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure.
This BlowTie unit can be easily disassembled for cleaning using a Phillips head screw driver.
Designed to suit 8mm OD (5/16") Evabarrier Tubing.
Specifications:
1. Suits pressures 0-15psi (but with different gauges the unit can go above 100psi)
2. Made from food-grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides
If you are looking for a compact digital gauge with backlight illumination click here. This should only be used on a blowtie if you have excess tubing to stop liquid reaching the gauge. If liquid enters the digital gauge it will break.
When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on Pump or Glycol systems.
Compatible with:
JoinTech Male Connector with Auto Shut Off x 1/2 Inch BSPT
JoinTech Male Connector with Auto Shut Off x 13mm Barb
Features:
- JoinTech Black UV Stable Design
- Equipped with Auto Shut Off Valve
- Vacuum Rating of 60psi
- Connections:
Female Plug Quick Disconnect
1/2" BSP Male Thread - Medical Grade Materials:
Body: High-Strength, Chemically Resistant Polyketone Plastic
Spring: 316 Stainless Steel
O-Ring: EPDM - Operating Pressure: Vacuum to 60 PSI
- Temperature Tolerance: -40°C to 138°C
- 3/8" Flow Path
From: Kegland
When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on the hosing used to attach to Pumps or Glycol systems.
Compatible with:
JoinTech Male Connector with Auto Shut Off x 1/2 Inch BSPT
JoinTech Male Connector with Auto Shut Off x 13mm Barb
Features:
- JoinTech Black UV Stable Design
- Equipped with Auto Shut Off Valve
- Vacuum Rating of 60 PSI
- Connections:
Female Plug Quick Disconnect
13mm Barb - Medical Grade Materials:
Body: High-Strength, Chemically Resistant Polyketone Plastic
Spring: 316 Stainless Steel
O-Ring: EPDM - Operating Pressure: Vacuum to 60 PSI
- Temperature Tolerance: -40°C to 138°C
- 3/8" Flow Path
From: Kegland
When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on Pump or Glycol systems.
Compatible with:
JoinTech Female Connector with Auto Shut Off x 13mm Barb
JoinTech Female Connector with Auto Shut Off x 1/2 Inch BSPT Male
Features:
- JoinTech Black UV Stable Design
- Equipped with Auto Shut Off Valve
- Vacuum Rating of 60psi
- Connections:
Male Plug Quick Disconnect
1/2" BSP - Medical Grade Materials:
Body: High-Strength, Chemically Resistant Polyketone Plastic
Spring: 316 Stainless Steel
O-Ring: EPDM - Operating Pressure: Vacuum to 60 PSI
- Temperature Tolerance: -40°C to 138°C
- 3/8" Flow Path
From: Kegland
When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on Pump or Glycol systems.
Compatible with:
JoinTech Female Connector with Auto Shut Off x 13mm Barb
JoinTech Female Connector with Auto Shut Off x 1/2 Inch BSPT Male
Features:
- JoinTech Black UV Stable Design
- Equipped with Auto Shut Off Valve
- Vacuum Rating of 60psi
- Connections:
Male Plug Quick Disconnect
13mm Barb - Medical Grade Materials:
Body: High-Strength, Chemically Resistant Polyketone Plastic
Spring: 316 Stainless Steel
O-Ring: EPDM - Operating Pressure: Vacuum to 60 PSI
- Temperature Tolerance: -40°C to 138°C
- 3/8" Flow Path
From: Kegland
Oxebar 20L Amber PET Keg & Pressure Fermenter Tank
The Oxebar Mono Barrier Keg by KegLand. Beverages will last 3 x Longer than competitors single PET layer kegs.
Fit up to 3 of these badboys in your Series X.1, X or 4.1 (aka XL).
Or fit up to 6 of these in a Series X.1 Plus!
Not only will it protect your beer from damaging light (amber tinting) it will also keep your beverages fresher for up to 3 times as long due to the Mono Barrier PET Polymer Matrix.
It also comes with a floating dip tube with cage filter. Is easy to undo and stack on top of each-other upside down with disconnects attached.
The 20L Oxebar Amber PET Kegs come with a Green Pressure Relief valve rated to 65psi.
Dimensions:
640mm High
235mm Diameter
Other uses:
- Overflow Homebrew Keg
- Cleaning Keg for Commercial Keg Buyers
- In a pinch it could be used as a Pressure Fermenter Tank, although we would highly recommend going for a 30L FermZilla Pressure Brewing Kit for adequate single batch sizing as well as being able to get your hand inside to clean properly.
20L Brimful, ideally 19.5L fill for Kegging purposes.
If you are going to use it as a fermenter, we would recommend between 15L and 18L. When fermenting you will need a spunding valve such as the BlowTie Spunding Valve Kit OR Integrated Gauge BlowTie Kit (0-15psi).
Remember, a PRV is a not a spunding valve.
Includes:
1 x 20L Amber Mono Barrier PET Oxebar Keg
1 x Dual PCO1881 Lid assembly with Oxebar Black Handle
1 x Green Pressure Relief Valve for Keg Lids / MK4 Reg - 65psi
1 x 100cm Silicone Hosing with Stainless Steel float and Hop Filter Cage
1 x RED Multi Gas Post Plastic Carbonation Cap
1 x Yellow Multi Liquid Post Plastic Carbonation Cap
From: Kegland
New commercial 20 litre stainless kegs with D-Type spear included and rubber base and handle.
Premium brand new kegs rated to 130psi working pressure and made using a robotic orbital welding machine with super smooth welding marks making them easier to clean.
These kegs are also passivated, giving them a matte finish, to ensure superior rust protection.
The black rubber handles and base allows easier transportation and less scuffs on the floor of your cool room / kegerator.
Features:
- new, with D-Type spear
- maximum working pressure: 130psi
Dimensions: approx. 240mm Diameter x 570mm High
Stated Capacity: 20 litres
Serial Numbers: No
A new 9.5 litre keg with ball-lock gas in and beer out posts, and lid with pull-ring pressure relief valve.
These premium brand new kegs with Rubber Handle are rated to 130psi working pressure and are made using a robotic orbital welding machine. They have super smooth welds, making them sanitary and easier to clean. The black rubber on these kegs also make them a little nicer to use as they are less likely to damage your floors or crack plastic lining inside your kegerator.
They also have a lid with an internal tab/hook under the lid designed specifically for attaching a hop ball for dry hopping.
Add a Carbonating Keg Lid to enable you to carbonate your beer quickly (overnight) at your standard serving pressure.
Note: Hop Ball not included.
From: Kegland
Dimensions: approx. 214mm diameter x 370mm high
Rated to: 130PSI
A new 19 litre keg with ball-lock gas in and beer out posts, and lid with pull-ring pressure relief valve.
These new kegs are made with a high-barrier elastomer O-Rings to keep your beverage fresher for longer.
Unlike Silicone O-Rings, LOW2 O-Rings are made from synthetic M-Class Cross-Linked elastomer for superior oxygen barrier properties to prevent O2 ingress. This helps keep your beverage fresher for longer.
These premium brand new kegs are rated to 130PSI working pressure and are made using a robotic orbital welding machine. They have smooth welds making them sanitary and easier to clean. The black rubber on these kegs makes them a little nicer to use around your house as they are less likely to damage your tile floors or crack plastic lining inside your kegerator.
They also have a lid with an internal tab/hook under the lid designed specifically for attaching a container for dry hopping.
Add a Carbonating Keg Lid to carbonate your beer quickly (overnight) at your standard serving pressure.
Dimensions: approx. 214mm Diameter x 629mm High
DO NOT USE BLEACH TO CLEAN. Bleach will break down stainless steel and causing pitting to occur.
4L PET Oxebar Keg with Cap and Handle (PCO38 )
Keep your oxygen-sensitive beverages fresher for longer with the Oxebar Monolayer. We recommend this product for storing beer up to 3-6 months.
The new lightweight and reusable plastic kegs are brought to you by Oxebar and KegLand. Store your homebrew in a more convenient size, take it away camping or to a bbq. The new shorter profile 4L under 330mm will fit in most chilly bins or esky coolers. You can also dispense with it lying on its side.
Do not Exceed 4 Bar / 58psi or 45°C
This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19L corny kegs. The small 4L size is convenient, light weight and perfect for sharing beverages with friends.
This 4L keg is light weight, compact and has extreme oxygen barrier properties. This extremely low gas transmission means your beverage will stay much fresher for longer. Even if you do consume the beverage in a short time, that short time will have much less oxygen transmission compared to other PET kegs on the market. Suitable for carbonated and non-carbonated beverages.
This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head. The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design.
What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.
Dimensions
Diameter:155mm
Height: 325mm
Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically. This is a very simple process and it's nothing to be feared. We recommend that this container be pressure tested every 2 years up to 6 bar. The instructions for this are:
1. Remove RED prv and fit GREY prv (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water. DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar.
4. Hold the keg at 6 bar for 1 minute
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30C
From: Kegland
8L Keg Oxebar Monolayer Keg With Cap and Handle (PCO38)
This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19 litre corny kegs. The small 8 liter size is convenient, light weight and perfect for sharing beverages with friends.
This 8L keg is light weight, compact and has high oxygen barrier properties with 3x better (less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages.
This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head. The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design.
What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.
Dimensions
Diameter:155mm
Height: 520mm
Do not Exceed 4 Bar / 58psi or 45°C
Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically. This is a very simple process and it's nothing to be feared. We recommend that this container be pressure tested every 2 years up to 6 bar. The instructions for this are:
1. Remove RED PRV and fit GREY PRV (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water. DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar.
4. Hold the keg at 6 bar for 1 minute.
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30°C
From: Kegland
This replacement Keg Lid is suitable for Cornelius Type 19L and 9.5L Kegs.
Features:
- High quality stainless steel
- NEW Low2 O-ring (Yellow)
- Ring pull pressure relief valve
- Inside hook to attach hop bombs or a hop tube
Hop Tube Not Included*
What is Low2?
Low2 O-Rings are the new standard of homebrew kegs from KegLand. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.
From: Kegland
Soda Carbonator - Keg Reactor Lid
This is the easy way to have continuous soda water on tap. Don't waste your time with Sodastream or other more expensive carbonators. This simple device makes it easy to have continuous carbonated soda water fed from your mains water supply.
Please see the description below on how to set this up.
Nothing is more refreshing than having your own soda water on tap at home. Sodastream units are great but filling up those tiny 1L bottles is a pain and those small CO2 cylinders run out fast and are expensive to swap. Solve this problem once and for all with the Continuous Soda Carbonator Keg Reactor Solution.
KegLand has invented this really simple to use lid that attaches to a standard ball lock keg. You can use one a 19L ones or a 9.5L keg.
All you have to do is:
1. Position the keg inside your fridge, kegerator, coolroom, or anywhere cold (ideally below 5C).
2. Attach your dispensing tap of choice to the soda water outpost.
3. Attach your gas to the gas in post.
4. Set your CO2 regulator that is connected to the gas post to 30-50psi. (higher pressures will give you more carbonation so set your regulator pressure to achieve desired carbonation level).
NOTE: It's recommended to use a check valve in your CO2 line. We recommend this Duotight check valve or this one that is integrated into the gas ball lock disconnect.
5. The first time you use this unit it's a good idea to purge the air from the headspace of the keg. To do this pull the PRV on the keg lid about 5 times for 2-second bursts.
6. Connect the mains water to the water inlet post on the lid of the keg. We recommend using a check valve for this application to prevent soda water going back into your house mains. We recommend this Duotight check valve. Also, it's a good idea to reduce your mains water pressure. Most domestic mains water pressure is over 100psi. For this unit to work well the mains water pressure should be 10-15psi higher than your regulator set pressure (from step 4). To regulate your water pressure we would recommend the use of the Inline Regulator Inline Regulator.
If you are looking for a mains water connection, you could use our diverter valve (this is not a stainless steel unit) with some 1/4" PE Water Line and a Duotight 6.5mm x 8mm Reducer.
That's it. This simple unit will give you continuous soda water connected to your mains water. Great for a bar cafe, restaurant or just at home.
This is capable of carbonating 10 Litres per hour if you have sufficient ability to cool the water. The colder the water and the higher the gas pressure (from step 4) the higher the carbonation level you will have. If you want to have extremely high soda water production speeds you can pre-chill the water by having one (or several) keg/s placed inline in front of the carbonation reactor. This will help pre-cool the water before it enters the carbonator. Alternatively, you can use a chiller such as the G40 glycol chiller to pre-chill the water before it enters the carbonator. If you do this you can increase your carbonation rate to over 30 litres per hour.
From: Kegland
Replacement Low2 keg lid o-ring seal for corny keg lids. Suitable for any 19L, 9.5L corny keg - ball lock or pin lock.
Also suits FermZilla 2" tri-clamp pressure lids.
Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.
From: Kegland
Replacement pressure relief valve (PRV) for corny kegs, MK4 Regulators, and FermZilla Lids.
Now available in three pressure ratings:
Yellow - 17 PSI
Red - 35 PSI
Green - 65 PSI
Grey - 100 PSI
From: Kegland
Colour coded Yellow and Red Ball Lock Keg Post O-Rings. Silicone for superb malleability and spring back memory performance.
We've all been there, not looking or not thinking and trying to put a gas disconnect on a liquid post. Yes, there's a notch in it. Yes, there are words IN and OUT. But you're busy! You don't have time to go searching, it should just be in your face obvious that it's a liquid or a gas post. KegLand finally has the answer with the long awaited colour coded Gas and Liquid Post Sets Red & Yellow.
FAQ
Why not Low2 O-Rings? Aren't they supposed to be better?
There is one fundamental reason why we didn't and shouldn't use Low2 O-rings for a post. Spring-Back Memory - Leak prevention.
Low2 has a lot of memory, while silicone does not. This means that if you use a Low2 O-ring on your keg posts, keep the keg cold in the fridge, and have everything connected, then later remove and reattach the disconnects, the O-ring's memory could be slightly off unless you reseat it in exactly the same position. That misalignment can lead to a potential leak.
We use Low2 on the Hatch Lid O-Ring because its a face seal that can withstand 100's of PSI worth of pressure, and even if flattened slightly under pressure it can be reseated quite easily.
A Radial Seal (Post O-Ring) is much harder to manipulate.
All independent testing with Low2 Keg Lid O-rings was done with silicone post o-rings. So rest assured you're getting the best possible product that means less leak spots, and better chemical resistance and performance.
Comes with:
5 x Yellow Liquid In Post O-Rings
5 x Red Gas Out Post O-Rings
We would recommend applying food grade lubricant to your o-rings on a regular basis to prolong their life. Especially after deep cleaning.
From: Kegland
These 29L stainless steel vessels are designed just like a commercial beer keg but with a large 10cm (4inch) tri-clover opening at the top so you can easily get inside the keg to clean it out. This new 29L size is perfect for doing 20-25L batches so you have a bit of spare head space inside the Kegmenter.
This Kegmenter is bundled with a stainless 4inch tri-clamp ball lock lid which will enable you to turn your kegmenter into a unitank fermenter, and pressurisable so it can also be used as a keg.
The Kegmenter can hold 2.5bar which makes it possible to carbonate and ferment in the same vessel. You can either carbonate naturally with the use of our adjustable pressure relief valve (spunding valve) or if you are using a CO2 gas cylinder you can force carbonate.
Being able to hold pressure also means you can push the beer out of the fermenter directly through a filter or even dispense directly from fermenter to draft beer tap if you wanted to.
The chimes on the Kegmenters have specifically been designed to be taller than normal chimes so they are high enough to give clearance over the stainless posts on the Ball Lock Post Lid. This means the Kegmenters can be stacked. The interlocking stacking chimes means the kegs can be safely stacked up to 4 high.
Pressure Limitations
Maximum Working Pressure: 2.5 BAR
Test Pressure: 5 BAR
Wall Thickness (Body/Chimes): 1.8mm/2.1mm
Diameter: approx. 39.5cm
Height: approx. 38cm
From: Kegland
The Liquid Ball Lock Post for Keg Coupler is a liquid ball lock post with a female 5/8 inch connection. It allows you to connect ball lock disconnects to a keg coupler making it extremely easy to swap over from a corney keg to a commercial keg (you will need the correct coupler for the keg as well).
These seals replace the red o-ring seal inside the 20L Oxebar kegs.
Includes:
5 x Low2 Keg Lid Seals to suit the 20L Oxebar Keg (Yellow)
These seals replace the red o-ring seal inside the 20L Oxebar keg lids.
What is Low2?
Low2 O-Rings are the new golden yellow standard of homebrew kegs brought to you by KegLand Australia. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.
The same material O-Ring (Low2) were independently tested on the 19L stainless steel kegs by GunnLab.
From: Kegland
Mini Core 360 Adaptor for 74g Canister/Bulb (G1/2 Male x 5/8-18UNF Female).
This adaptor for the Core 360 Mini Regulator will allow you to use the oversized disposable 74gram co2 bulbs so you can take your keg system anywhere.
The oversized 74gram CO2 bulbs are large enough to dispense almost a whole 19L keg of beer so they are a really great choice for portable keg systems.
NOTE: The regulator itself and 74grams bulbs need to be purchase separately.
From: Kegland
Mini Gauge 0-15psi (0-1.5bar) - for inline Duotight regulator or Blowtie.
This gauge is designed to fit into either our inline regulator or our Blowtie unit. These can be used for water or gas.
Specifications
- Pressure: 0-15psi (0-1bar)
- Graduations: PSI + Bar
- Material: Brass/Plastic/Copper Capillary
- Gauge Diameter: 20mm
- Probe Diameter: 7.8mm (designed to fit 8mm hole)
- Accuracy: These gauges are accurate to 10% of the whole pressure range.
WARNING:
Do not exceed gauge pressure. If you exceed gauge pressure it will damage the capillary in the gauge and prevent the gauge from working correctly. NEVER exceed the maximum gauge display pressure range.
Not tested or approved for pure oxygen.
If you are looking for a compact digital gauge with backlight illumination click here.
From: Kegland
Digital Illuminated Mini Gauge 0-90psi (0-6.2bar) - Duotight 8mm Stem.
Traditional analogue gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle. This age old technique works quite well especially in large gauges, but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue. With very small gauges, such as a 27mm x 27mm Mini Gauge, it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components.
Kegland has developed the worlds most compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor. This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions is required.
Specifications:
Battery Life: More than 2 years (using the mini gauge once a day)
Battery Type: CR2032
Auto Battery Saver: YES, screen automatically turns off after 15sec
Size: 27mm x 27mm
Duotight Stem: 8mm
NOTE: This gauge is not suitable for measuring pressure of liquids. It is only for measuring gas pressure. If liquid gets into the pressure transducer it will damage the gauge. If you want to measure liquid pressure you can purchase one of these analogue gauges:
KL07696 - Duotight Compatible Push in Pressure Gauge
From: Kegland
Digital Illuminated Mini Gauge 0-90psi (0-6.2bar) for Integrated Blowtie and In-line regulators.
Traditional analogue gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle. This age old technique works quite well especially in large gauges but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue. With very small gauges such as a 27mm x 27mm Mini Gauge it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components.
Kegland has developed this compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor. This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions is required.
Specifications:
Battery Life: More than 2 years (using the mini gauge once a day)
Battery Type: CR2032
Auto Battery Saver: Yes, screen automatically turns off after 15sec
Size: 27mm x 27mm
Radial O-ring Stem: 7.8mm Bore
NOTE: This gauge is not suitable for measuring pressure of liquids. It is only for measuring gas pressure. If liquid gets into the pressure transducer it will damage the gauge. If you want to measure liquid pressure you can purchase one of these analogue gauges:
This digital mini gauge can be used to upgrade your:
Blowtie Spunding Valve
Inline Regulator
Core 360 Mini Regulator
If you would like to use the mini gauge to attach to other hobbie projects then you should consider the Duotight Compatible Digital Mini Gauge with part number KL18081 that has the 8mm duotight push in stem. This makes it easy to fit to other 8mm duotight fittings, tubing etc.
From: Kegland
