Duotight - 8mm Female - 5-Way Multi-Tee

This particular Duotight tee saves on space and purchasing multiple generic equal tee's when setting up a 4-tap kegerator, or if you simply want to plumb up to four liquid or gas lines from one source.

Simply plumb your gas line in to any of the connections, then split it off to up to four different lines. If you want to cap off certain lines, we would recommend using an 8mm plug.

Flush mountable!
Looking for high quality push-in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Why do we use double o-rings?
The secret to the superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them.  The double o-ring means we literally have twice the sealing surface when compared with other push in fittings.  This makes Duotight fittings even more reliable and reduces the chance of a leak significantly.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes Duotight fittings the most reliable push fit fittings on the market.

Compatible with:

EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.

EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds.   When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA-free and is the number one choice for many long-lasting food-grade applications.

From: Kegland

Duotight 8mm OD retaining circlip, suits any Duotight 8mm fitting. When clipped into place, this circlip prevents the collar of the Duotight fitting from being pushed inwards, making it impossible for the fitting to release its grip on any hose!

Note: Duotight fittings, ball lock disconnects and hose sold seperately.

From: Kegland

Duotight - 8mm (5/16') Plug

This fitting is used for gas or liquid leak testing purposes with Duotight manifolds or fittings.
Use it instead of attaching hosing to a disconnect which has other leak spot potential.

Suitable for 8mm Duotight fittings.

It is particularly useful for testing MK5 regulators and ball lock disconnects without the need for hosing and more valves.

From: Kegland

Duotight - 8mm x 9.5mm Reducer.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.

These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

From: Kegland

Duotight - 9.5mm (3/8") Female x 1/2" Female Thread.

It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. 

These push in fittings are suitable to be used up to 100 psi.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

Note: colour may vary.

From: Kegland

Duotight - 9.5mm (3/8”) Female x ½" Male Thread Ball Valve.

It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. 

These push in fittings are suitable to be used up to 100 psi.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

Note: colour may vary.

From: Kegland

Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread.

It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. 

These push in fittings are suitable to be used up to 100 psi.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

Note: colour may vary.

From: Kegland

Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread Bulkhead (suits TempTwister).

Looking for high quaility push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them.  The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings.  This makes these fittings even more reliable and reduces the chance of a leak significantly.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi

Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.

What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.

EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds.   When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.

From: Kegland

The BlowTie Diaphram Spunding Valve - a great tool if you want to control the pressure retained in a pressure vessel that is releasing pressure. It has been designed for simplicity and ease of putting together. Many brewers use this spunding valve in combination with the FermZilla pressure rated fermenters.

This is the new "BlowTie 2" upgarded model which has the integrated pressure gauge. The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure. This BlowTie unit can be easily disassembled for cleaning using a screw driver. Designed to suit 8mm (5/16") tubing. It's compatible with both the 4mm ID Tubing or 5mm ID.

This compact solution for adjusting residual pressure in your fermenter makes pressure control easier than it's ever been. This can be used for compressed air, CO2, nitrogen, mains water supply and many other things but its primary use is to control the residual pressure inside fermenters.

Specifications:
1. Suits pressures 0-23psi (but with different gauges the unit can go above 100psi)
2. Made from food grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides

The design utilises the reliability of the Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.

Pressure Fermentations
With the popularity of pressurised fermentation it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.

Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg it is often a good idea to have head pressure in the keg you are filling into especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process.

Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation. Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.

The BlowTie has been made completely differently taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure.

Instructions:
Use the yellow adjustment knob to control the pressure coming out of the pressure vessel. Clockwise is higher pressure and anticlockwise is lower pressure. We would recommend gassing a keg to a known pressure e.g. 15psi then attach your BlowTie Kit to the keg and adjust to 10psi.

These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.

IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)

Material: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland

The Duotight Inline Regulator - these compact inline regulators have been designed to suit 8mm (5/16") tubing.

Suits pressures 0-150psi however this unit is packed with the 0-60psi gauge as standard. Suitable for mains water pressure, also suitable for liquid or gas.

- Made from Acetal/POM, EPDM o-rings and stainless teeth
- Suits 8mm (5/16) OD tubing
- Includes integrated 0-60psi Pressure Gauge

For higher pressures such as mains water supply we recommend the 4mm ID Tubing, or 5mm ID if you do not need as high pressures and you would prefer higher flow rate.

This compact solution for adjusting water and gas pressure can be useful in many different applications. It can be used for compressed air, CO2, nitrogen, mains water supply and many other things.

The design utilises the reliability of the Kegland patented Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.

These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.

IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)

Made From: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland

Duotight push in fitting for 8mm line to 5/8inch thread - ideal for keg couplers and tap shanks.

Duotight fittings feature a double o-ring sealing design for a more secure seal. The seals are not only high quality EPDM o-rings but also it has two of them. The double o-ring means there is literally twice the sealing surface when compared with other push in fittings. This makes Duotight fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that you can bend the hose with a much tighter radius without leaking issues. 

We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used for up to 100 psi.

Duotight 8mm (5/16) one way check valve/non-return valve.

This very handy fitting could save your regulator and is a good investment. This particular type of check valve has low opening pressure of only 1 psi. It is suitable for clean liquids such as water or for gas. The spring and internal components are made with stainless steel and quality EPDM seals.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. 

Fits 8mm outer diameter tube. 

Note: colour may vary.

From: Kegland

This Duotight Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.

Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.

Fits 8mm outer diameter tube.

From: Kegland

This Duotight Push-Fit Tee - 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.

Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.

Fits 8mm outer diameter tube.

Note: colour may vary.

From: Kegland

Duotight - 8mm x 1/4 inch BSP Male.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.

These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

From: Kegland

This manifold splits one line into two, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This manifold splits one line into four, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This manifold splits one line into six, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This rigid 50mm long joiner is made from strong polypropylene. It's useful to make rigid joins with push in fittings that are dead straight. Although it's possible to make joins using short pieces of 8mm OD Evabarrier 5mm Beer Line this is far more flexible and when mounting parts to a gas board or wall its will often make things much neater if you use these instead.

The 50mm length is long enough so even after pushing right into two duotight 8mm fittings on both ends you should still have a exposed length of about 3mm so you can still relatively easily take the fittings apart later.

From: Kegland
Dimensions: 8mm OD x 6mm ID x 50mm long

This really handy device is great for filling kegs, keg to keg transfers or fermenter to keg transfers.

Fantastic for use with Fermentasaurus or other pressurisable fermenters.

Simply attach this device to the output gas post of your Keg then when the keg is full it will prevent further liquid exiting the gas post. This means you can literally set and forget and fill kegs automatically without the risk of kegs overflowing all over the floor.

For even better results we recommend this product to be used with the Duotight - BlowTie Diaphram Spunding Valve - Adjustable PRV.  This blowtie spunding valve will also enable to to apply head pressure to the keg meaning you can control the flow speed but also reduce the foam generated in the filling process particularly for carbonated beverages like beer.

This flow stopper includes:

• 2 x duotight 8mm x 5/8 push in fittings
• 1 x ball float
• 1 x stainless spring
• 2 x straight 8mm joiners
• 1 x acrylic sight glass (with 5/8 male thread on either side)

Made exclusively for the Duotight manifolds and Gen 3.0 Duotight 8mm fittings to be mounted to a flat surface.

These can swivel around if you need to mount on a particular angle once stuck down.
They can also easily be removed from the 8mm Duotight side as they simply click/clamp in to each other.

If you are to mount this inside your Kegerator / Keezer, you must do so when the unit is off / warm. It will not stick as well in a moist / cold environment. Best to give it at least 24 hours of stick time before attaching weight / hosing to it.

Wipe down surface with isopropyl alcohol prior to sticking.

Most commonly to be used with:

• 8mm (5/16) duotight x 6 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 4 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 2 Way Manifold with Check Valves & Isolation Valves
• and duotight - 8mm (5/16) x 5 Way Multi-Tee

If you want to know if your Duotight fitting will fit this, it must be a grey Duotight that has a black collet piece.

Not suitable for 8mm ball lock disconnects
Not suitable for multiple re-applications

From: Kegland

EVABarrier Black Lightshield 4mm ID x 8mm OD - 12m Roll.

This hose is suitable for a wide range of 8mm push in fittings, either for hydroponic/gardening use or outdoor keg dispensing where UV can damage the product.

Algae will always thrive if sunlight and an exposed nutrient solution is available. That is why it is crucial to use the correct hosing when it comes to hydroponic systems and or outdoor beer dispensing systems.

Prevention is the best cause of action when it comes to algae control. EVABarrier LightShield Black should be your number one choice of hosing when setting up your indoor or outdoor growing space.
UV stable hosing that will not kink or burst under normal use.

Specifications:
4mm Internal Diameter
8mm Outer Diameter
12m Roll

EVABarrier Hosing
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings.  The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.

Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier and now with LightShield technology an excellent UV and Visible light blocking properties. The significantly better barrier properties means your beverage is better protected from oxygen and also has a better barrier to CO2 loss.  So your beer will stay fresher for longer and not lose carbonation like other beer line types.  In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period.  EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.

Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable.  This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.

From: Kegland

EVABarrier Red Lightshield 5mm ID x 8mm OD - 12m Roll

Red semi-transparent EVABarrier for kegging setups. Easily see your gas lines in minimal light without confusion.

This high quality beer line will keep your previous beverage in it's best possible condition in the process.

This 5mm size is the one of the most common sizes for kegerator setups.

When using this 5mm ID size you will need to use about 3-4 meters of beer line to get adequate flow resistance between your keg and tap for most kegerator setups.

Pressure Rating (with 1.5x safety factor)
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)

This new Red EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.

Red Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings.  The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.

Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier.  The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss.  So your beer will stay fresher for longer and not loose carbonation like other beer line types.  In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period.  EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.

Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable.  This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.

From: Kegland

A 10 inch filter housing for filtering your beer prior to bottling or kegging, or to filter water.

For beer this filter works best when used when transferring cold uncarbonated beer. All you will need to do is purchase some hosing, clamps, ball locks (if transferring to or between kegs) and a 1 Micron Filter to use this system.

- Clear high pressure housing
- Purge valve to expel air pockets
- ½” BSP inlet and outlet
- Includes Duotight 9.5mm (3/8"") fittings 
- Brass threaded ports for durability
- Compatible with other 10” filter systems

Note: you will need tubing to match the fittings (not included).

You will need a filter insert to use this system, like our 1 Micron Washable Filter (for filtering beer) or a 0.5 Micron Carbon Water Filter, (for water filtering).

Not suitable for hot liquids.

A rugged and durable push fit, inline filter strainer. 

Available in both 8mm and 10mm push fit size.

The detachable cap and body allow for easy servicing and cleaning.

Do not apply excessive vibration, torque, shock or other strong loads to the filter as the filter body may damage or collets may be dislocated.

Filter grade: 100 mesh
Colour: Black
Max. Pressure: 170psi
Temperature: Air -20C, Liquid 65C
Height: approx. 70mm

FermZilla - SS Ball Float & 80cm Silicone Dip Tube and Filter Kit. Suits Tri-Conical and All Rounder Models.

This simple design allows you to extract the clearest possible liquid in your pressure vessel with the added security of our new filter included. This helps prevent blockages in your carbonation cap poppet. As the liquid level decreases the float goes down at the same time. Perfect for sampling the sediment free!

This 80cm silicone dip tube and stainless steel float with filter suits the FermZilla Tri-Conical fermenter. Also compatible with Kegmenters and Modified Ball Lock Kegs (not minikegs).

From: Kegland

Floating Dip Tube Filter（80 Mesh 304 Stainless) - For FermZilla or Kegmenter.

Made from HDPE and 304 Grade stainless steel, this product can be boiled or sanitised in the full range of cleaners that we sell. The plastic HDPE is over moulded onto the stainless mesh to make a seamless finish. The end cap can easily pop off for cleaning.

How frustrating is hops getting blocked in your poppet, tap, ball valves and practically everywhere else. This handy little filter can be used on your silicone floating dip tubes to prevent hops or other solids getting sucked into the dip tube itself. The 304 stainless 80 mesh is fine enough to filter out hops and many other solids but not so fine that it gets blocked up easily. If you have a FermZilla or stainless Kegmenter this add on extra is a must.

From: Kegland

The Gas Ball Lock Post for Keg Coupler is a liquid ball lock post with a female 5/8 inch connection. It allows you to connect ball lock disconnects to a keg coupler making it extremely easy to swap over from a corney keg to a commercial keg (you will need the correct coupler for the keg as well). 

Gas Free Ball Lock Line Cleaning Kit

Are you ever in a situation where you don't want to unhook your gas line from your kegs, or have ball lock disconnects that you need to clean over at the sink but don't want to take your gas line all the way over there? Well, Kegland thought of a better way. Why not fill a PET Bottle with your cleaner / sanitiser and pump it without gas!

This little device can also be used as a mini party keg without a gas source (should be consumed well within 24 hours of pumping). BYO Liquid disconnect, hose and picnic tap.

Contains:
1 x KegLand Yellow Carbonation Cap
1 x KegLand PCO Tee Piece (Female x Male x Male)
1 x Mini Yellow Hand Pump
1 x 30cm Piece of EVABarrier Line 5mm ID x 8mm OD (can be stretched for larger PET bottles)

From: Kegland