Gas Free Ball Lock Line Cleaning Kit

Are you ever in a situation where you don't want to unhook your gas line from your kegs, or have ball lock disconnects that you need to clean over at the sink but don't want to take your gas line all the way over there? Well, Kegland thought of a better way. Why not fill a PET Bottle with your cleaner / sanitiser and pump it without gas!

This little device can also be used as a mini party keg without a gas source (should be consumed well within 24 hours of pumping). BYO Liquid disconnect, hose and picnic tap.

Contains:
1 x KegLand Yellow Carbonation Cap
1 x KegLand PCO Tee Piece (Female x Male x Male)
1 x Mini Yellow Hand Pump
1 x 30cm Piece of EVABarrier Line 5mm ID x 8mm OD (can be stretched for larger PET bottles)

From: Kegland

This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla.

It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel. 

Diameter: approx. 66mm Heigh: approx. 300 mm.

From: Kegland

Hoses play a huge role in draft beer dispensing. They carry gas from the tank to the coupler and beer from the keg right up to the faucet. These pipes are of soft, flexible but durable material. They are usually of Vinyl and Polypropylene. The hoses are also part of glycol pythons.

Hoses are connected through adapters and barbs to form the entire dispensing system. The length really depends on how far your serving point is from the keg. You might have to shorten or cut out from a large bundle. For any of this, you require a Hose and Tubing Cutter.

This cutter is sturdy and sharp that cuts right through the hose in a jiffy without leaving any rough edges too.

• Material: Plastic
• Finish: Raw
• Color: Black

Looking for a smaller option, you'll find one here.

From: Krome Dispense

A tool for cutting hose and tube, with a stainless steel blade.

From: Krome Dispense

This unit has been designed to fit Kegland standard Single, Double and Triple Tap Kegland Kegerator Towers or any other 76mm diameter font. 

Keep your beer icy-cold with this insulated tower/font cover right out of the first drop. Most kegerators that we sell include a font fan that blows cold fridge air up the font. With that said heat loss from the stainless font surface causes the font temperature to rise meaning that a small amount of beer contributes to the "first pour foam effect".

These extra thick covers are made from 7mm neoprene, meaning your beer will stay cold even if the hot sun is beating down directly on the font.

This helps save power as your fridge will not be working as hard, and you pay less in power. So this thing practically pays for itself!

How to Install

1. Remove taps from the font. (no need to remove the shank from the font, just the taps).

2. Pull the insulated cooler down over the font.

3. Mark the tap holes and use a sharp pair of scissors to cut a hole in the neoprene jacket.

4. Re-attach the taps.

NOTE: Nail cutting scissors are particularly good for this application, or a 5/8" Hole Punch.

Please note these only come with a Kegland logo. They are not sold in plain black.

From: Kegland

Now updated with the all new duotight 8mm Ball Lock Disconnect (Grey+Red/Gas)

This kit has been designed for simplicity and ease of putting together. 

This Kit Contains:
1 x BlowTie Spunding Valve Gen 2 with 0-15psi Integrated Gauge
1 x Duotight 8mm (5/16") x Ball Lock Disconnect (Grey+ Red/Gas)
1 x Rigid 8mm Plastic Joiner

All new compact BlowTie Spunding Valve Gen2 Integrated Kit. If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job. 

If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job.

The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure.

This BlowTie unit can be easily disassembled for cleaning using a Phillips head screw driver.

Designed to suit 8mm OD (5/16") Evabarrier Tubing. 

Specifications:
1. Suits pressures 0-15psi (but with different gauges the unit can go above 100psi)
2. Made from food-grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides

If you are looking for a compact digital gauge with backlight illumination click here. This should only be used on a blowtie if you have excess tubing to stop liquid reaching the gauge. If liquid enters the digital gauge it will break.

Oxebar 20L Amber PET Keg & Pressure Fermenter Tank

The Oxebar Mono Barrier Keg by KegLand. Beverages will last 3 x Longer than competitors single PET layer kegs.

Fit up to 3 of these badboys in your Series X.1, X or 4.1 (aka XL).
Or fit up to 6 of these in a Series X.1 Plus!

Not only will it protect your beer from damaging light (amber tinting) it will also keep your beverages fresher for up to 3 times as long due to the Mono Barrier PET Polymer Matrix.

It also comes with a floating dip tube with cage filter. Is easy to undo and stack on top of each-other upside down with disconnects attached.

The 20L Oxebar Amber PET Kegs come with a Green Pressure Relief valve rated to 65psi.

Dimensions:
640mm High
235mm Diameter

Other uses:
- Overflow Homebrew Keg
- Cleaning Keg for Commercial Keg Buyers
- In a pinch it could be used as a Pressure Fermenter Tank, although we would highly recommend going for a 30L FermZilla Pressure Brewing Kit for adequate single batch sizing as well as being able to get your hand inside to clean properly.

20L Brimful, ideally 19.5L fill for Kegging purposes.

If you are going to use it as a fermenter, we would recommend between 15L and 18L. When fermenting you will need a spunding valve such as the BlowTie Spunding Valve Kit OR Integrated Gauge BlowTie Kit (0-15psi).

Remember, a PRV is a not a spunding valve.

Includes:
1 x 20L Amber Mono Barrier PET Oxebar Keg
1 x Dual PCO1881 Lid assembly with Oxebar Black Handle
1 x Green Pressure Relief Valve for Keg Lids / MK4 Reg - 65psi
1 x 100cm Silicone Hosing with Stainless Steel float and Hop Filter Cage
1 x RED Multi Gas Post Plastic Carbonation Cap
1 x Yellow Multi Liquid Post Plastic Carbonation Cap

From: Kegland

New commercial 20 litre stainless kegs with D-Type spear included and rubber base and handle.

Premium brand new kegs rated to 130psi working pressure and made using a robotic orbital welding machine with super smooth welding marks making them easier to clean. 

These kegs are also passivated, giving them a matte finish, to ensure superior rust protection.

The black rubber handles and base allows easier transportation and less scuffs on the floor of your cool room / kegerator. 

Features:
- new, with D-Type spear
- maximum working pressure: 130psi

Dimensions: approx. 240mm Diameter x 570mm High
Stated Capacity: 20 litres
Serial Numbers: No

A new 9.5 litre keg with ball-lock gas in and beer out posts, and lid with pull-ring pressure relief valve.

These premium brand new kegs with Rubber Handle are rated to 130psi working pressure and are made using a robotic orbital welding machine. They have super smooth welds, making them sanitary and easier to clean. The black rubber on these kegs also make them a little nicer to use as they are less likely to damage your floors or crack plastic lining inside your kegerator.

They also have a lid with an internal tab/hook under the lid designed specifically for attaching a hop ball for dry hopping.

Add a Carbonating Keg Lid to enable you to carbonate your beer quickly (overnight) at your standard serving pressure.

Note: Hop Ball not included.

From: Kegland
Dimensions: approx. 214mm diameter x 370mm high
Rated to: 130PSI

Streamline Your Brew Day. Skip the Bottles.

Make the switch to kegging with the Mangrove Jack's 19L Cornelius Keg—a brand-new, food-grade stainless steel vessel built for home brewers who value efficiency. No more hours of sanitising bottles; just clean one keg, fill it, and pour perfect pints straight from your kegerator. Designed for everyday durability, this keg combines rugged construction with user-friendly features that make storage and transportation a breeze.

Key Specifications:

• Capacity: 19 L (5 US Gal) – ideal for standard home brew batches

• Body Material: High-grade stainless steel for corrosion resistance and flavour protection

• Handle & Base: Rubber top and bottom for easy transportation and stacking.

• Diameter: 22.3 cm – fits neatly into most standard kegerators

• Connections: Fully compatible with standard Cornelius (Corny) parts for easy maintenance and customisation

• Safety Certification: NSF Approved for safe food and beverage consumption

• Branding: Embossed Mangrove Jack's logo for a premium, authentic finish

Pour with Confidence.

Whether you're carbonating a crisp lager or serving a hop-heavy IPA, this keg delivers consistent performance at working pressures up to 130psi. Its robust rubber protectors absorb knocks during transport, while the stainless steel interior keeps your beer tasting as fresh as the day it was brewed. Upgrade your setup today and enjoy the convenience, consistency, and professional feel that only kegging can provide.

A new 19 litre keg with ball-lock gas in and beer out posts, and lid with pull-ring pressure relief valve.

These new kegs are made with a high-barrier elastomer O-Rings to keep your beverage fresher for longer.

Unlike Silicone O-Rings, LOW2 O-Rings are made from synthetic M-Class Cross-Linked elastomer for superior oxygen barrier properties to prevent O2 ingress. This helps keep your beverage fresher for longer.

These premium brand new kegs are rated to 130PSI working pressure and are made using a robotic orbital welding machine. They have smooth welds making them sanitary and easier to clean. The black rubber on these kegs makes them a little nicer to use around your house as they are less likely to damage your tile floors or crack plastic lining inside your kegerator. 

They also have a lid with an internal tab/hook under the lid designed specifically for attaching a container for dry hopping.

Add a Carbonating Keg Lid to carbonate your beer quickly (overnight) at your standard serving pressure.

Dimensions: approx. 214mm Diameter x 629mm High

DO NOT USE BLEACH TO CLEAN. Bleach will break down stainless steel and causing pitting to occur.

4L PET Oxebar Keg with Cap and Handle (PCO38 )

Keep your oxygen-sensitive beverages fresher for longer with the Oxebar Monolayer. We recommend this product for storing beer up to 3-6 months.

The new lightweight and reusable plastic kegs are brought to you by Oxebar and KegLand. Store your homebrew in a more convenient size, take it away camping or to a bbq. The new shorter profile 4L under 330mm will fit in most chilly bins or esky coolers. You can also dispense with it lying on its side.

Do not Exceed 4 Bar / 58psi or 45°C

This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19L corny kegs. The small 4L size is convenient, light weight and perfect for sharing beverages with friends.

This 4L keg is light weight, compact and has extreme oxygen barrier properties. This extremely low gas transmission means your beverage will stay much fresher for longer. Even if you do consume the beverage in a short time, that short time will have much less oxygen transmission compared to other PET kegs on the market. Suitable for carbonated and non-carbonated beverages.

This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head.  The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design.

What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.

Dimensions
Diameter:155mm
Height: 325mm

Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically.  This is a very simple process and it's nothing to be feared.  We recommend that this container be pressure tested every 2 years up to 6 bar.  The instructions for this are:
1. Remove RED prv and fit GREY prv (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water.  DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar. 
4. Hold the keg at 6 bar for 1 minute
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30C

From: Kegland

8L Keg Oxebar Monolayer Keg With Cap and Handle (PCO38)

This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19 litre corny kegs. The small 8 liter size is convenient, light weight and perfect for sharing beverages with friends.

This 8L keg is light weight, compact and has high oxygen barrier properties with 3x better (less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages.

This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head.  The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design. 

What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.

Dimensions
Diameter:155mm
Height: 520mm

Do not Exceed 4 Bar / 58psi or 45°C

Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically.  This is a very simple process and it's nothing to be feared.  We recommend that this container be pressure tested every 2 years up to 6 bar.  The instructions for this are:
1. Remove RED PRV and fit GREY PRV (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water.  DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar. 
4. Hold the keg at 6 bar for 1 minute.
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30°C

From: Kegland

Micromatic is a world leader in high quality, European keg couplers, and these D Type (US Sankey) Keg Couplers are no exception.

From: Micromatic Thread: 5/8" BSP

D-Type Keg Coupler - Full Stainless - with Duotight 5/8" to 8mm push fit fittings.

Includes:
1 x - D-Type Coupler with 5/8" Male Beer and Gas threads
2 x - duotight 5/8" duotight to 8mm push in
1 x - Non-Return Ball or Torpedo check piece (Non-Return Liquid)
1 x - Gas Duck Bill valve (Non-Return Gas)

How to install Gas Duck Bill Valve
Remove black EPDM washer inside 1 of the duotight push in fittings that you will use for gas. The duck bill valve is a washer as well as a non-return check piece. It is optional, you do not have to use the non-return check pieces for gas or liquid.

From: Kegland

This replacement Keg Lid is suitable for Cornelius Type 19L and 9.5L Kegs.

Features:
- High quality stainless steel
- NEW Low2 O-ring (Yellow)
- Ring pull pressure relief valve
- Inside hook to attach hop bombs or a hop tube 
Hop Tube Not Included*

What is Low2?
Low2 O-Rings are the new standard of homebrew kegs from KegLand. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.

From: Kegland

Soda Carbonator - Keg Reactor Lid

This is the easy way to have continuous soda water on tap. Don't waste your time with Sodastream or other more expensive carbonators. This simple device makes it easy to have continuous carbonated soda water fed from your mains water supply.

Please see the description below on how to set this up.

Nothing is more refreshing than having your own soda water on tap at home. Sodastream units are great but filling up those tiny 1L bottles is a pain and those small CO2 cylinders run out fast and are expensive to swap. Solve this problem once and for all with the Continuous Soda Carbonator Keg Reactor Solution.

KegLand has invented this really simple to use lid that attaches to a standard ball lock keg. You can use one a 19L ones or a 9.5L keg.

All you have to do is:
1. Position the keg inside your fridge, kegerator, coolroom, or anywhere cold (ideally below 5C).

2. Attach your dispensing tap of choice to the soda water outpost.

3. Attach your gas to the gas in post.

4. Set your CO2 regulator that is connected to the gas post to 30-50psi. (higher pressures will give you more carbonation so set your regulator pressure to achieve desired carbonation level).
NOTE: It's recommended to use a check valve in your CO2 line. We recommend this Duotight check valve or this one that is integrated into the gas ball lock disconnect.

5. The first time you use this unit it's a good idea to purge the air from the headspace of the keg. To do this pull the PRV on the keg lid about 5 times for 2-second bursts.

6. Connect the mains water to the water inlet post on the lid of the keg. We recommend using a check valve for this application to prevent soda water going back into your house mains. We recommend this Duotight check valve. Also, it's a good idea to reduce your mains water pressure. Most domestic mains water pressure is over 100psi. For this unit to work well the mains water pressure should be 10-15psi higher than your regulator set pressure (from step 4). To regulate your water pressure we would recommend the use of the Inline Regulator Inline Regulator.

If you are looking for a mains water connection, you could use our diverter valve (this is not a stainless steel unit) with some 1/4" PE Water Line and a Duotight 6.5mm x 8mm Reducer.

That's it. This simple unit will give you continuous soda water connected to your mains water. Great for a bar cafe, restaurant or just at home.

This is capable of carbonating 10 Litres per hour if you have sufficient ability to cool the water. The colder the water and the higher the gas pressure (from step 4) the higher the carbonation level you will have. If you want to have extremely high soda water production speeds you can pre-chill the water by having one (or several) keg/s placed inline in front of the carbonation reactor. This will help pre-cool the water before it enters the carbonator. Alternatively, you can use a chiller such as the G40 glycol chiller to pre-chill the water before it enters the carbonator. If you do this you can increase your carbonation rate to over 30 litres per hour.

From: Kegland

Replacement Low2 keg lid o-ring seal for corny keg lids. Suitable for any 19L, 9.5L corny keg - ball lock or pin lock.

Also suits FermZilla 2" tri-clamp pressure lids.

Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.

From: Kegland

Replacement pressure relief valve (PRV) for corny kegs, MK4 Regulators, and FermZilla Lids.

Now available in three pressure ratings:

Yellow - 17 PSI
Red - 35 PSI
Green - 65 PSI
Grey - 100 PSI

From: Kegland

Clear lubrication gel for keg parts such as o-rings, couplers, party pumps. Use with plastic and rubber components to avoid cracks and extend their life. Just a little of this goes a long way.

Food grade keg lube is completely safe to use with all components. FDA listed, high quality, tasteless and odourless grease.

• Food safe lube for keg parts

• Use with both rubber and plastic parts to avoid easy damage

• Long lasting

• Keeps for years

Specifications

• Food Grade lubricant is safe for all home brewery needs

• Keeps rubber parts soft and supple

• Helps prevent leaks

Size: 1oz (28g)

Made in: Germany

Service temperature: -20C to +45C

From: Krome Dispense

Colour coded Yellow and Red Ball Lock Keg Post O-Rings. Silicone for superb malleability and spring back memory performance.

We've all been there, not looking or not thinking and trying to put a gas disconnect on a liquid post. Yes, there's a notch in it. Yes, there are words IN and OUT. But you're busy! You don't have time to go searching, it should just be in your face obvious that it's a liquid or a gas post. KegLand finally has the answer with the long awaited colour coded Gas and Liquid Post Sets Red & Yellow.

FAQ
Why not Low2 O-Rings? Aren't they supposed to be better?

There is one fundamental reason why we didn't and shouldn't use Low2 O-rings for a post. Spring-Back Memory - Leak prevention.

Low2 has a lot of memory, while silicone does not. This means that if you use a Low2 O-ring on your keg posts, keep the keg cold in the fridge, and have everything connected, then later remove and reattach the disconnects, the O-ring's memory could be slightly off unless you reseat it in exactly the same position. That misalignment can lead to a potential leak.

We use Low2 on the Hatch Lid O-Ring because its a face seal that can withstand 100's of PSI worth of pressure, and even if flattened slightly under pressure it can be reseated quite easily.

A Radial Seal (Post O-Ring) is much harder to manipulate. 

All independent testing with Low2 Keg Lid O-rings was done with silicone post o-rings. So rest assured you're getting the best possible product that means less leak spots, and better chemical resistance and performance.

Comes with:
5 x Yellow Liquid In Post O-Rings
5 x Red Gas Out Post O-Rings

We would recommend applying food grade lubricant to your o-rings on a regular basis to prolong their life. Especially after deep cleaning.

From: Kegland

Kegging your beer and keeping it cold will help to keep your beer at its best for as long as possible, and there is nothing quite like pouring a nice cold beer at the end of a long day.

This starter kit provides you with the basic items you need to begin kegging your beer. You will also need a fridge or freezer (temperature controlled) to keep your keg of beer cold and a co2 cylinder to carbonate and serve.

To get a good pour when serving simply adjust Ball Lock Beer Duotight Disconnect - Flow Control.

Use 0.5m to connect the MK5 CO2 Regulator to the Ball Lock Gas Duotight Disconnect and 1.5m to connect the Ball Lock Beer Duotight Disconnect - Flow Control to the Duotight - 6.5mm x 8mm Reducer and Beer Tap - Keg Picnic Tap - Duotight. 

This kit includes:

• Mangrove Jack's 19L Keg or Kegland Corny Style 19L Keg
  
• Ball Lock Beer Duotight Disconnect - Flow Control
• Ball Lock Gas Duotight Disconnect
• Regulator - MK5 CO2 - Tool-Free
• EVABarrier 4mm ID / 8mm - 2m
• Duotight - 6.5mm x 8mm Reducer
• Beer Tap - Keg Picnic Tap - Duotight

Use the dropdown boxes above if you would like to add any of the following items:

• Mangrove Jack's CO2 Cylinder (3.4L, 2kg capacity) (pick up only)
• CO2 Cylinder - Reconditioned & Certified Steel 7 lb (3.2kg) Cylinder (pick up only)
• Sodastream CO2 Adapter - Deluxe with Pin Adjustment
• Duotight 8mm Push Fit Check Valve (suitable for 5.5mm ID / 8mm OD line)

This item is not held in stock and is ordered in on request. Please contact to check availability and shipping cost. 

The Kegmaster Premium XL 2 Tap Kegerator from Keg King is a premium kegerator full of features for a professional experience when serving beverages at home.

Get up to 2 kegs on tap and save space as well as cooling times! 

The Kegmaster Premium can store up to 4 x 19 L ‘Corny’ kegs giving you the option of conditioning 2 kegs while serving from 2. Alternatively, the Kegmaster Premium XL can fit 2 x 20 L PET Kegs + 1 x 19 L ‘Corny’ keg, 3 x 20 L SS Commercial Kegs, or 1 x 50 L SS Commercial Keg.

The internal volume has increased from previous versions to an impressive 160 L capacity while keeping the kegerator compact enough to fit in typical ‘kegerator-size’ spaces. 

The Kegmaster Premium XL also includes the UltraTap for laminar flow and the perfect pour! Also includes are built-in, low-profile rollers so you can easily move your kegerator in position and a gas cylinder bracket that can be installed at the back for efficient storage of your CO2 cylinder.

With a preassembled font and gas line, there is minimal assembly required, meaning you can get round to serving your beer or other carbonated beverage quickly and with ease. 

Features:

• Built in rollers for easy moving – removeable and upgradeable to castors.
• Reversible Door – orient to open how you like.
• Font Fan with speed control – keeps your font cold and runs more quietly.
• Internal light – handy for inspecting keg connections.
• Suitable for free standing installations – can also be installed under counters.
• R600a Refrigerant – environmentally 

The kegerator is easy to set up and you only need to add a C02 Cylinder, pop in some kegs and you're good to go.

What's Included

• Kegmaster Premium XL Kegerator
• Preassembled 2-tap font and gas line
• MKX Regulator

Specifications

Height: 850 mm with rollers 830 mm without rollers 890 mm with castors
Width: 610 mm
Depth: 660 mm
Internal Height: 724.9 mm
Internal Width: 511.9 mm
Internal Depth: 405.1 mm
Volume: 160 L
Weight: 43 Kg
Power: 220-240V 50Hz
Climate Class: T
Refrigerant: R600a (40g)
Insulation: Cyclopentane
Packaged dimensions: H 88 cm W 66 cm D 69 cm

This item is not held in stock and is ordered in on request. Please contact to check availability and shipping cost. 

The Kegmaster Premium XL 2 Tap Kegerator from Keg King is a premium kegerator full of features for a professional experience when serving beverages at home.

Get up to 2 kegs on tap and save space as well as cooling times! 

The Kegmaster Premium can store up to 4 x 19 L ‘Corny’ kegs giving you the option of conditioning 2 kegs while serving from 2. Alternatively, the Kegmaster Premium XL can fit 2 x 20 L PET Kegs + 1 x 19 L ‘Corny’ keg, 3 x 20 L SS Commercial Kegs, or 1 x 50 L SS Commercial Keg.

The internal volume has increased from previous versions to an impressive 160 L capacity while keeping the kegerator compact enough to fit in typical ‘kegerator-size’ spaces. 

The Kegmaster Premium XL also includes the UltraTap for laminar flow and the perfect pour! Also includes are built-in, low-profile rollers so you can easily move your kegerator in position and a gas cylinder bracket that can be installed at the back for efficient storage of your CO2 cylinder.

With a preassembled font and gas line, there is minimal assembly required, meaning you can get round to serving your beer or other carbonated beverage quickly and with ease. 

Features:

• Built in rollers for easy moving – removeable and upgradeable to castors.
• Reversible Door – orient to open how you like.
• Font Fan with speed control – keeps your font cold and runs more quietly.
• Internal light – handy for inspecting keg connections.
• Suitable for free standing installations – can also be installed under counters.
• R600a Refrigerant – environmentally 

The kegerator is easy to set up and you only need to add a C02 Cylinder, pop in some kegs and you're good to go.

What's Included

• Kegmaster Premium XL Kegerator
• 2 x 19 L ‘Corny’ Kegs
• Preassembled 2-tap font and gas line
• MKX Regulator

Specifications

Height: 850 mm with rollers 830 mm without rollers 890 mm with castors
Width: 610 mm
Depth: 660 mm
Internal Height: 724.9 mm
Internal Width: 511.9 mm
Internal Depth: 405.1 mm
Volume: 160 L
Weight: 43 Kg
Power: 220-240V 50Hz
Climate Class: T
Refrigerant: R600a (40g)
Insulation: Cyclopentane
Packaged dimensions: H 88 cm W 66 cm D 69 cm

This Forward Sealing Flow Control beer faucet features a forward-sealing design with the added benefit of having a lever to adjust beverage flow. In normal rear-sealing faucets, the entire faucet has to drain of beer. In forward-sealing flow control faucets the faucet keeps beer in it so the inside doesn’t have a chance to get sticky, making cleaning much easier. It also reduces the chance of off flavours transferring to your beer while you pour.

This Beer faucet uses a threaded spout, compatible with Nukatap fittings, that can quickly and easily be removed and replaced with a range of other spouts including:

• Growler Filler – features a 1/2″ barb for easy growler filling
• Stout Spout – features an internal creamer disc for the perfect pint
• Ball Lock Post – allows for easy fill of smaller kegs or connect a counter pressure filler or line cleaner.

The Flow Control model is perfect for users that often switch between beer styles with different carbonation levels, or want to conveniently switch from pouring pints to filling growlers without having to make adjustments to the regulator pressure settings.

• Made with 304 Grade stainless steel and comes with a lever to control the flow
  of your beer
• It has a modular, threaded spout that can fit a variety of different attachments
• The front sealing faucet eliminates the build-up of mold and bacteria.
• The threaded spout easily unscrews from the faucet
• Pour a pint and then fill a growler in no time at all
• Works great to bottle beer with a Ball lock adapter and a Beer Gun

Also available without Flow Control.

From: Krome Dispense

The forward sealing design shuts off the flow of beer at the front of the tap which will keep wild yeast and bacteria out of the interior of the tap body. This design will also keep your faucet moist. Since it is not drying out you will not get a sticky tap so the opening will always be easy.

This Beer faucet uses a threaded spout, compatible with Nukatap fittings, that can quickly and easily be removed and replaced with a range of other spouts including:

• Growler Filler – features a 1/2″ barb for easy growler filling
• Stout Spout – features an internal creamer disc for the perfect pint
• Ball Lock Post – allows for easy fill of smaller kegs or connect a counter pressure filler or line cleaner.

Other tap designs require you to replace the tap on the font when changing from one beer style to the next. This tap allows you to simply unscrew the standard spout and attach a range of different spout options to suit your beer style.

Compatible with all our shanks and tap handles.

Material: polished stainless steel
Body thread: 1-1/8 X 18 UNEF
Lever thread: 3/8" X 16 UNC

Note: handle and shank not included.

Also available with flow control.

From: Krome Dispense

The Liquid Ball Lock Post for Keg Coupler is a liquid ball lock post with a female 5/8 inch connection. It allows you to connect ball lock disconnects to a keg coupler making it extremely easy to swap over from a corney keg to a commercial keg (you will need the correct coupler for the keg as well). 

These seals replace the red o-ring seal inside the 20L Oxebar kegs.

Includes:
5 x Low2 Keg Lid Seals to suit the 20L Oxebar Keg (Yellow)

These seals replace the red o-ring seal inside the 20L Oxebar keg lids.

What is Low2?
Low2 O-Rings are the new golden yellow standard of homebrew kegs brought to you by KegLand Australia. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.

The same material O-Ring (Low2) were independently tested on the 19L stainless steel kegs by GunnLab. 

From: Kegland

With the portable dispensing kit, you will now be able to dispense straight from the keg (think party kegs!) which means you will be able to take your homemade beer to parties, BBQs and other gatherings where you can share your brews with others.

The kit has an inlet for standard threaded disposable 16g CO2 canisters plus adaptors for paintball cylinders, 74g CO2 cartridges and SodaStream cylinders!

Kit Contains:

• Portable Keg Dispensing Kit 
• Threaded Gas Ball Lock Disconnect 
• Threaded Liquid Ball Lock Disconnect 
• Mini Keg Ball Lock Cap 
• Mini Keg Diptube Hosing 10 L 
• Mini Keg 10 L 

With the portable dispensing kit, you will now be able to dispense straight from the keg (think party kegs!) which means you will be able to take your homemade beer to parties, BBQs and other gatherings where you can share your brews with others.

The kit has an inlet for standard threaded disposable 16g CO2 canisters plus adaptors for paintball cylinders, 74g CO2 cartridges and SodaStream cylinders!

Kit Contains:

• Portable Keg Dispensing Kit 
• Threaded Gas Ball Lock Disconnect 
• Threaded Liquid Ball Lock Disconnect 
• Mini Keg Ball Lock Cap 
• Mini Keg Diptube Hosing 3 L 
• Mini Keg 3 L 

With the portable dispensing kit, you will now be able to dispense straight from the keg (think party kegs!) which means you will be able to take your homemade beer to parties, BBQs and other gatherings where you can share your brews with others.

The kit has an inlet for standard threaded disposable 16g CO2 canisters plus adaptors for paintball cylinders, 74g CO2 cartridges and SodaStream cylinders!

Kit Contains:

• Portable Keg Dispensing Kit 
• Threaded Gas Ball Lock Disconnect 
• Threaded Liquid Ball Lock Disconnect 
• Mini Keg Ball Lock Cap 
• Mini Keg Diptube Hosing 5 L 
• Mini Keg 5 L