This duotight 8mm (5/16") adaptor is designed to suit the Nukatap Mini and will allow you to couple your Nukatap mini to a wide range of other 8mm(5/16") duotight fittings or be able to attach to the Duotight Flow Control Ball Lock Disconnect. This particular type of flow control ball lock disconnect includes a "tang" at the top of the push in fitting that couples with this adaptor. The combination of the two fittings prevents the tap spinning around while in use.

Other Parts Sold Separately

Nukatap Mini

Ball Lock Beer Duotight Disconnect - Flow Control

From: Kegland

This bracket is used to mount a Nukatap Mini in either 6.35mm or 8mm to a table or bench. Ideal for impromptu gatherings in the park!

This bracket is compatible with tables that are up to 90mm thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side.

Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket.

From: Kegland

 Nukatap Mini - Mini Design - Ideal Flow Rate for Small Systems

Most conventional beer taps are designed with a 10mm diameter nozzle/spout so you can pour pint in just over 10 seconds. This type of flow rate is great for high turnover bars and commercial venues but this high flow rate requirement is not not necessary or desirable for all applications.  For compact portable systems, or for home brew draft systems, a slower flow rate is easier to control the flow and further reduces foaming issues due to the low liquid volume stored in the tap body. 

This Nukatap mini is also more ideal for pouring smaller doses.  For example cocktails where 150-250ml of liquid is dispensed is difficult to control with a high flow rate tap.  For portable systems this tap and FC ball lock disconnect assembly is small enough to literally put in your pocket making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight.

Forward Sealing
Forward sealing taps are absolutely the way to go when it comes to beer taps.  The issue with rear sealing taps is that beer dries up on the tap piston.  This is not sanitary and as more and more beer dries up in these components the tap can almost glue complete shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside).  These older legacy design still exist probably due to poor education.  The forward sealing design do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduced maintenance.  In may instances the price is similar so there is no reason to use a poorly designed rear sealing tap.  All Nukatap taps are forward sealing.

Laminar Flow
Just like the Nuktap SS and Nukatap FC, the Nukatap Mini has been designed with laminar flow in mind.  Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage.  Think about how many times a beer tap opens and closes in it's lifetime - 1000 or maybe 10,000 times?  Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer.  Extensive modeling has been done on this Nukatap design to improve laminar flow.

Integrated Seals that are Indestructible and more Sanitary
Unlike other designs, the Nukatap Mini body is made from POK making it strong, robust and able to be autoclaved.  The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry.  The seals internally in are over-molded meaning NO fissures or cracks exist for bacteria, crud or yeast to hide.

Superior First Pour Foam Due to Low Thermal Mass and Conductivity
First pour foam is an issue caused by a warm tap body. For most taps to pour well it's important to dispense enough beer to cool the tap body down before the tap will pour well.  In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials.  The Nukatap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene and POK.  The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. 

Long Shank Alternative (Sold separately in Duotight design)
Most conventional beer taps require a large 22mm hole to be drilled through the wall of your keezer/cooler/wall.  Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal.  This new long shank alternative is designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself.  For walls up to 80mm thick we have provided three screws however if the wall is thicker you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type.

Another advantage of this new design is the tap will never accidentally rotate.  Typically other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate.  This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.

Other Accessories (Sold Separately)
Nukatap Mini - Wall Mount Shank Kit - duotight 8mm (5/16")
Nukatap Mini - Self Closing Tap Spring
Nukatap Mini - duotight adaptor - 8mm (5/16")
Flow Control Ball Lock Disconnect

This bracket is used to mount a Nukatap Mini in either 6.35mm or 8mm to a cooler/esky/chilly bin or your home refrigerator or bar fridge. No need to drill any holes!

This bracket is compatible with walls/fridges that are up to 90mm thick. It can be adjusted to have the wing nut clamp in either direction, simply unscrew the flange piece from the threaded rod, then unscrew, then thread from the opposing side.

Please note: This item does not include the Mini NukaTap or Shank pieces. It is simply the stainless steel bracket.

From: Kegland

NukaTap Mini - Wall Mount Shank Kit (Duotight 8mm).

This shank kit is specifically designed to suit the Nukatap Mini taps and will allow you to connect the Nukatap Mini to a cooler box, kegerator, keg fridge, coolroom wall or any other flat surface.

New Innovative Shank Design
Unlike other shank kits this shank kit doesn't use a bulky 5/8" bar stock. The issue with 5/8 bar stock is it acts as a heat sink and due to the fact that most other shanks sit inside the insulated wall this results in a substantial amount of warm beer coming out of the tap before cold beer starts flowing. This means a "first pour foam" effect which wastes beer, can result in sour beer, and ultimately negatively effects the quality of the beverages being served. This new design has the beer line feed all the way directly up to the back of the tap greatly reducing the volume of non-refrigerated beer.

No Spinning Shanks
If you have ever installed a traditional 5/8" long shank you will know how frustrating it is when you use the tap and the tap starts rotating. This new design of shank alternative uses three screws that lock the tap into a fixed position and prevents the taps from rotating. If you loosen the 1/2" stainless tap collet you can still have the flexibility to rotate the tap to any orientation but once the collet is tight interlocking teeth on this shank kit and the Nukatap Mini will hold the tap permanently in the correct orientation.

Easy Installation
Unlike other long shank kits, this kit doesn't require large 22mm hole saw to be used to drill through the wall. As no shank is required, only a hole large enough to accommodate the beer line is required. As a result only an 8mm conventional drill bit is all that is necessary and this makes the installation easier. If, however, you are concerned about the small amount of beer sitting in the beer line in the wall not being refrigerated you can also shell out a larger diameter of foam on the inside of the wall to allow cold air to circulate around the beer line thus reducing the non-refrigerated beer in the line even more. If you wanted to do this a Step Drill Bit is the best tool for the job.

Any Wall Thickness
Other shank kits will require you to purchase a specific length shank for a specific wall thickness. This new shank alternative will fit any wall thickness. If you have wall thicknesses that are less than 80mm thick then you can use the included screws that have "snap off" points so you can simply cut the screws down to the desired length. If, however, the wall is thicker than 80mm you can simply purchase a conventional screw from the hardware store and screw the shank kit to your wall. If the substrate is firm enough you may not even need to go all the way through the wall, so a common 30mm long screw may be all that is required.

Specifications:

• Beer Line Diameter: Suits any EVABarrier beer line in with 8mm ID Beer line such as the 4mm x 8mm EVABarrier beer line or the 5mm x 8mm EVABarrier beer Line.
• Collet and Screw Cover: 304 Grade Stainless Steel
• O-ring Material: Dual o-ring Silicone/EPDM combination
• Plastic Mounting: POK
• Temperature Range: -10C and up to 100C
• Max Pressure: 150psi

NOTE: Nukatap Mini is SOLD SEPARATELY. 

Nukatap Mini Flow Control Set
This bundle combines the four items needed for a standard ball lock set up, including a Duotight 8mm Flow Control Ball Lock Disconnect for fine flow rate control.

Includes:

• Nukatap Mini
• NukaTap Mini Self Closing Tap Spring
• NukaTap Mini - Duotight Adaptor - 8mm
• Keg Connector - Duotight Flow Control - 8mm Liquid

Nukatap Mini - Mini Design - Ideal Flow Rate for Small Systems
Most conventional beer taps are designed with a 10mm diameter nozzle/spout so you can pour pint in just over 10sec.  This type of flow rate is great for high turnover bars and commercial venues but this high flow rate requirement is not not necessary or desirable for all applications.  For compact portable systems, or for home brew draft systems, a slower flow rate is easier to control the flow and further reduces foaming issues due to the low liquid volume stored in the tap body. 

This Nukatap mini is also more ideal for pouring smaller doses.  For example cocktails where 150-250ml of liquid is dispensed is difficult to control with a high flow rate tap.  For portable systems this tap and FC ball lock disconnect assembly is small enough to literally put in your pocket making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight.

Forward Sealing
Forward sealing taps are absolutely the way to go when it comes to beer taps.  The issue with rear sealing taps is that beer dries up on the tap piston.  This is not sanitary and as more and more beer dries up in these components the tap can almost glue complete shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside).  These older legacy design still exist probably due to poor education.  The forward sealing design do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduced maintenance.  In may instances the price is similar so there is no reason to use a poorly designed rear sealing tap.  All Nukatap taps are forward sealing.

Laminar Flow
Just like the Nuktap SS and Nukatap FC, the Nukatap Mini has been designed with laminar flow in mind.  Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage.  Think about how many times a beer tap opens and closes in it's lifetime - 1000 or maybe 10,000 times?  Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer.  Extensive modeling has been done on this Nukatap design to improve laminar flow.

Integrated Seals that are Indestructible and more Sanitary
Unlike other designs, the Nukatap Mini body is made from POK making it strong, robust and able to be autoclaved.  The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry.  The seals internally in are over-molded meaning NO fissures or cracks exist for bacteria, crud or yeast to hide.

Superior First Pour Foam Due to Low Thermal Mass and Conductivity
First pour foam is an issue caused by a warm tap body. For most taps to pour well it's important to dispense enough beer to cool the tap body down before the tap will pour well.  In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials.  The Nukatap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene and POK.  The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced. 

Long Shank Alternative (Sold separately in Duotight design)
Most conventional beer taps require a large 22mm hole to be drilled through the wall of your keezer/cooler/wall.  Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal.  This new long shank alternative is designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself.  For walls up to 80mm thick we have provided three screws however if the wall is thicker you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type.

Another advantage of this new design is the tap will never accidentally rotate.  Typically other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate.  This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.

From: Kegland

This pretty handy kit contails all the seals needed for both the standard Nukatap and the Flow Control Nukatap.

The majority of these seals would never normally need to be replaced, but in the event of accidental loss / extreme commercial use please replace washers with the addition of food-grade lubricant to ensure their longevity.

Please refer to the parts diagram for seal locations:

SS Nukatap Parts List

Nukatap FC Parts List

If you have not changed your seals before, it's a great idea to take a note of which seal goes where as you remove the old ones!

Includes:

• The Nuke!
• Tap Coupling Washer
• Bonnet Washer
• 2 x Cup Seal
• Nozzle Washer

Also included (unique to the FC Nukataps):

• 2 x Shaft Seals
• Flow Bonnet Damper
• Shaft Cushion
• Flow Slider Seal

From: Kegland

Nukatap - the latest in beer dispensing tap technology. Now available in black with stainless spout.

What makes the Nukatap different among the other manufactured styles of taps on the market?
- First Pour Foam Reduction in Thermal Mass
- Improved Laminar Flow
- Most Sanitary Forward Sealing Design Design
- Longer Life Seals
- Move Versatile Tap Handle Angle

First Pour Foam Reduction
The reduction in thermal mass significantly reduces the first pour foam effect. The tap is often the warmest part of the draft system as it protrudes from the font/tower/fridge. As a result, it acts like a heat sink and only works well once enough cold beer flows through it to cool the tap body down. This reduction of thermal mass significantly improves the foam that is poured while the tap is cooling down.

Laminar Flow
The Nukashuttle design is the world’s first seamless shuttle. After many months of modelling and testing this new "Nuke" shaped shuttle design has the most fluid dynamic shuttle shape ever manufactured for a forward sealing tap. The streamline "nuke/missile" shape is how this new innovation earned its name "Nukatap". This leap forward in laminar flow means even highly carbonated beers pour like a dream with minimal turbulence and giving you the perfect pour every time.

Most Sanitary Design
The Nukashuttle is the world’s first seamless single-piece design. Traditional taps have a seal that is seated on a stainless-steel body creating small fissures that harbour solids, are potential sites for infection, and are not as ideal for clean in place (CIP). The Nukashuttle is an advanced TPV rubber matrix that been seamlessly formed over a durable PP skeleton. This single-piece design takes away the traditional fissures found in older manufacturing methods.

Long Life Seals
Unlike many other taps that use rubbers that can be degraded with caustic and acid compounds, the Nukatap has been made to suit a wide range of conditions. It's becoming more common to see sour beers/kombucha and other acetic and lactic acid beverages dispensed using draft systems. These acids, in particular, could cause an attack on the sealing compounds resulting in downtime, loss of product and reduced maintenance intervals. The Nukatap solves this problem and is the most chemically resistant tap we have ever manufactured. Unlike some older tap styles that have "metal on metal" rubbing components that can wear over time and have a "raspy feel" the Nukatap has been manufactured with a smooth gliding action that guarantees the longevity of the tap components. The TPV rubber matrix shuttle is also one of the most durable sealing mechanisms that can tolerate large amounts of leverage force from long tap handles that would otherwise traditionally degrade the seals in other tap designs. Other forward sealing designs exist but nothing with the same level of reliability. It’s easy to find other “perl” forward sealing design taps however these taps use a floating o-ring design which by all means is equally as sanitary however the floating o-ring requires the o-ring to move within the tap body to seal correctly. This movement is typically a problem as the tap ages and/or is not serviced regularly. The Nukatap bypasses this seal as the entire Nukashuttle is a single sealing piece.

Tap Handle Angle - 2.5degree Reverse Angle
The Nukataps have been manufactured with a 2.5 degree reverse angle. This allows for a wider range of taps handles to be used, in particular, long and/or heavy handles to work perfectly irrespective of the installation conditions.

Forward Sealing Design
Just like the Intertap and its predecessors, the Nukatap shuts off the flow at the front of the tap which in turn keeps wild yeast and bacteria out of the interior of the tap body.

What does Rear Sealing Design Mean?
Typically most beer taps use a rear sealing design and the beer in the tap drains from the body of the tap with the help from a vent hole drilled at the front of the tap. This drainage hole is a dark and wet cavity and is an ideal place for airborne bacteria and wild yeast to reproduce leaving a foul film that deteriorates the quality of your beer. Every time the faucet is opened contamination can occur.

Compatible with Intertap and Nukatap accessories:
- Auto-Close Spring
- Stout Spout
- Ball Lock Post Spout
- Growler Spout

From: Kegland

Prevent gas or liquid leaks on your MFL connections with this Nylon Flare Washer Olive for MFL Fittings (1/4"). This washer fits inside MFL connections such as on the MKIII/MK4 multi gas regulators, MFL ball lock disconnects, barbed swivel nuts, and 8mm push fit MFL connectors.

From: Kegland

A long Nylon Hose Brush for beer line cleaning on your kegging system.

Sizes:

• 4.76mm (3/16") x 167cm
• 9.53mm (3/8") x 167cm

Made by: Krome Dispense

The Party Pump Kit provides an easy way to dispense a commercial beer keg when you are away from electricity or don't have a CO2 cylinder.

Just put the keg in a bucket of ice and pump the beer out at your own leisure. This reliable and simple setup is easy to use and requires no power, no gas cylinder and no regulator. It's really the easiest way to dispense a keg at a party.

Features
- Easy to use
- No gas cylinder required
- No electricity required
- Plastic tap and beer line The hose comes un-assembled so you will need to assemble before use.

Note: Does not include keg coupler. Please be aware that you will need to make sure your keg coupler has the check valve installed.

Note: Beer must be drunk within 48 hrs.

From: Kegland

This handy PCO38 Tapping Head assembly is a great way to get into kegging. Using standard home brew ball lock disconnects this is convenient, light weight, robust and useful for wine, cocktails, beer, and other beverages.

This PCO38 tapping head assembly has been designed to suit standard PCO38 bottle necks.

The PCO38 keg system is a inexpensive keg system that utilises quality engineering plastics and efficient injection stretch blow mould processes to manufacture economical kegs and tapping heads for both home brewing and commercial beers.

This particular tapping head kit comes included with 2.5bar pressure relief valve, liquid and gas ball lock posts and dip tube.

The plastics used in the tapping head can withstand a wide range of chemicals used in the brewing industry and relatively high temperatures (over 100C).

NOTE: The keg shown in the photos is not included.

From: Kegland

Perfect for spraying down brewing equipment with dissolved cleaners or sanitisers.

Ideal for coupling with Multi-Post for Power Sprayer to turn the sprayer into a pressurised line cleaning device.

Includes:
1L Reservoir Tank
Power Sprayer Nozzle and Dip Tube
White plastic adjustment head sprayer
15cm USB C to Standard USB (for charging purposes)

Food Grade
This product is made from food grade, Santoprene, PP, PE, Silicone and Stainless Components.

Battery Life
The pump has large 18650 li-ion rechargeable battery. On a full charge the battery will empty the 1L tank 18-30 times so it lasts for ages.
NOTE: If you use fine mist it will be closer to 18 times but if you use a jet/stream the battery will last closer to 30 times.

Does Not Include:
USB wall charger
Multi-Post for Power Sprayer

From: Kegland

• 0-40psi / 0-250kPa / 0-2.5 Bar (kg/cm^2)
• Rubber Coated
• 8mm Push in Barb

This item is not held in stock and is ordered in on request. Please contact to check availability and shipping cost. 

RAPT Temperature Controlled Fermentation Chamber

This fermentation chamber has been designed to heat and cool your entire fermenter.  This is the ideal scenario as the whole fermentation vessel is placed in a temperature controlled environment which gives you the most even temperature and most precise control of your fermenter.

Many home made products can greatly be improved with perfect temperature control.  The RAPT Temperature Controlled Fermentation Chamber gives you an electrically efficient means of setting, monitoring and controlling temperature which is perfect for Beer Making, Wine Making, Salami Making, leavening bread, fermenting yogurt, kombucha, germinating seeds, growing sprouts, kimchi, sauerkraut, olives, cheese, making spirit washes.  Accurate temperature control is the key to getting reliable and repeatable results.

From -2°C up to 50°C all at the touch of your fingertips!

The control panel comes complete with an integrated colour TFT screen, the integrated secondary regulator that can be used to regulate gas into the chamber with our Inline Regulator with an integrated gauge or alternatively this can be switched over to the Gauge integrated BlowTie unit to regulate residual pressure in your fermenter.  The 4 button colour display conveniently shows a log of historic temperature graphs, allows you to start, set/stop temperature profiles and gives you access to other critical information for that particular fermentation.
For more accurate readings of the core temperature of your fermenter. We highly recommend using a thermowell like our 60cm duotight thermowell with the 2m probe extension for the RAPT Fermentation Chamber.

Perfect as a Kegerator too!
This multi purpose chamber can also be used as a kegerator.  In particularly cold climates where the ambient temp is below zero, this chamber can warm your kegs and prevent them from freezing.  This chamber also has a higher keg storage capacity than a conventional kegerator that takes up the same footprint.  This unit can hold 4 x 19L kegs on the floor and has enough headroom that you can also fit another layer of 9.5L half size kegs above this.  To fit beer taps, you can drill your own holes through the door.

Convert to Display Chamber
This Chamber comes with brushed stainless steel PU foam-filled door.  If you want to upgrade to a glass door the double glazed glass door can be purchased separately and switched over - coming soon.

What is RAPT?
RAPT is a dedicated Internet of Things (IOT) Hub for fermentation logging and control.  It's a free service whereby any RAPT enabled product can both log and store data to the hub where you can conveniently access this data.  The RAPT hub can also allow you to control your devices remotely giving you absolute control of the device irrespective of where you are.  The RAPT portal enables you to make complex temperature profiles that involved different temperature settings over time meaning you can start/run a temp profile giving you a set and forget experience.  The RAPT portal also controls the alert/notification process for you so you can receive email notifications in the off instance that something doesn't go to plan.

Specifications:
Integrated Heating: 50watt Heating Power
Cooling Capacity: 300watt Cooling Power
Max Power Consumption: 225 Watts
Refrigerant: r600a
Connectivity: Wifi (802.11) and Bluetooth
Temperature accuracy: +/- 0.1C
Temp Resolution: 0.1C
Integrated Screen: 2.8inch (diagonal) 320 x 240 Colour LCD TFT Active Matrix

External Dimensions:
Width: 540mm
Depth: 610mm
Height: 1760mm

Internal Dimensions:
Width: 440mm
Depth: 500mm
Height: 1300mm

To see the dimensioned drawings on this part click here.

Why buy an insulated fermentation chamber over a glycol chiller?
Typically in the past, some customers have needed to resort to glycol chillers to chill fermenters but this represents several issues:

1. Glycol chillers often require a very cold liquid to enter into a fermenter causing an excessively cold part in the fermenter core.
2. Glycol chillers consume significant amounts of power and in most instances more than double what this chamber would consume.
3. Glycol chillers often result in spilling sticky glycol especially when hoses are connected and disconnected to the fermenter.
4. Glycol chillers generally require penetrations through the walls/lid of the fermenter making the fermenter less sanitary and requiring more cleaning. "who needs that!"
5. Often fermenters are not made with sufficient insulation.  So when using a glycol chiller much of the chilling is lost which is not only power inefficient but the customer ends up with a large temperature gradient.  This temperature gradient can result in convection currents in the fermenter that make it difficult for yeast and other solids to settle out of suspension.  So clarification of the beer takes significantly longer.
6. Many glycol chillers and fermenter combinations do not have sufficient power or are not well enough insulated to cool to sub-zero temperatures.  So crash chilling is not possible.  This is a significant compromise to a temperature-controlled solution and also results in less ability to clarify the finished beer.

For these reasons KegLand has developed the worlds first dedicated RAPT enabled fermentation chamber that can cool down to -2C and heat up to 50C even in hot and cold weather.

The Google Play Android App can be downloaded via the link below.
https://play.google.com/store/apps/details?id=io.rapt

"This app is a web mobile wrapper that allows you to browse the RAPT portal/website so that the website renders into a mobile device screen increasing usability on your device.  It also gives you the added functionality of push notifications to your mobile device." 

From: Kegland

In Line Regulator with 8mm push fit connections.

This unit has no gauge. Looking for the Duotight Inline Regulator with Gauge?

This inline regulator is suitable for gas or liquid. The design has two main features:

1. Push In 8mm
It comes with 8mm push fit connectors so you can push your beer, water, gas line directly into the unit.  No need for hose clamps, just push your EVABarrier line directly into the connector and it's securely joined.

2. Handy Tee Bar Adjustment
These have been designed with a highly visible yellow tee bar adjustment knob.  Significantly easier than the previous designs that required a phillips head screw driver to adjust the pressure.

Constructed with Non-Corrosive Acetyl, Nitrile & Stainless Components. The Regulator body has two wall mounting points.

These regulators work great for reducing your mains pressure from 0-159psi. The maximum inlet pressure is 150psi.

From: Kegland

The Mangrove Jack's CO2 Regulator is a quality regulator that provides reliable gas control. 

Can be attached to any co2 cylinder with type 30 / W21.8 thread.

KegLand Mini 360 Core Actuator Regulator - Sodastream & 16g & 74g Bulb Compatible

The All-New Mini 360 Core Actuator Regulator is the most versatile mini regulator on the market. It is an extremely versatile mini regulator that can be used with either a Sodastream Canister, or the smaller disposable CO2 16g bulbs.

Unlike other regulator designs this new design requires no sodastream adaptor and you do not have the issues of trying to screw the bulb or sodastream cylinder into the regulator while gas leaks everywhere. This robust, convenient and superior design is just what you need for any portable keg system.

Please note this is not compatible with the 2kg, 3.5kg or 5.0kg CO2 Cylinders.

Features:

• Core Puncturing / Actuator - Zero gas lost to screwing in bulbs or Sodastream style cylinders.
• Interchangeable ball lock disconnect orientations (e.g. 45° Premium Ball lock to 90° Stainless Disconnects)
• 6.5mm duotight compatible hose barb (6.5mm x 8mm duotight) can also suit hose and stepless clamps (e.g. 4mm ID, 5mm ID or 6mm ID hose)
• Heavily Protected Mini Guage Dial. (Also interchangeable to different ranges)
• Common Pressure relief valve compatible. (65psi Green PRV as standard, compatible with 35psi Red and 100psi Grey)

Includes:
1 x Mini 360 Core Actuator Regulator
1 x 360° 6.5mm duotight compatible hose barb
1 x 360° FFL Fitting for MFL Disconnects
1 x Port end cap
1 x 65psi Green PRV
1 x Sodastream to 16g thread bushing

Upgrade to digital:
Upgrade to a more accurate digital gauge with this gauge.  This mini gauge is easier to read and has a backlight so you can also read the pressure easily in the dark.

WARNING:
Do not over tighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your Sodastream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator.

From: Kegland

A seal kit for the Mini 360 Core Actuator Regulator. Contains the o-rings for the piston, the red inlet washer, MK4 seat assembly o-ring, 2 x barbMFL outlet o-rings and x thumb screw o-rings.

For instructions on replacing the seals and/or general maintenance please refer to the product manual here.

From: Kegland

Mini duotight Regulator - 6.35mm (1/4'') Suits 16g and 74g Bulbs

Perfect introductory regulator for mini keg / oxebar keg set ups. This compact unit can take 16g and 74g CO2 bulbs. Travellers have never been so easy!

This regulator features a 6.35mm Duotight compatible barb, meaning you can connect just about anything within a matter of seconds. The most common easy attachment to your ball lock kegs would be adding 1 x Duotight 6.35mm (1/4") x Ball Lock Disconnect - (Grey + Red Gas).

If however you want to be a bit more protective with your beer not shooting back into the regulator you could minimise the damage by using a 6.35mm check-valve and some hosing to your ball lock disconnect.

Suitable Gas Cartridges are:
16g Cartridge / Bulbs
74g Big Bulb CO2 Cartridge 5/8-18UNF Thread

Please note, once you get liquid shoot back through it, it's no longer functional. Be extremely careful with overfilling your kegs or tipping them over when the gas has run out.

This regulator is capped at dispensing 30psi to ensure you do not accidentally over carbonate or exceed your kegs pressure rating. The gauge, however, shows up to 60psi just in case by heat ingress / expansion that it does not break the gauge.

From: Kegland

The Type 50 for Nitrogen - MK4 Dual Gauge gas regulator is the only regulator you'll ever need to buy for a deluxe nitrogen stout/cocktail setup. With a large body and precision diaphragm, this regulator provides high flow rates and very accurate adjustments in both PSI and KPA.

The most common problem with other regulators sold on the market was that contamination would occur through the seat and cap assembly within the regulator. This has now been solved with a second sintered filter on the underside of the seat assembly, within the regulator, to block contaminants.

New and Improved Features:
- Stronger Steel Gauges made from thicker steel
- Triple scale gauges in kPa, Bar and PSI
- New Colour Coded PRV valves.
- New M6 Mounting Holes for easy Mounting

From: Kegland

Type 30 - MK5 CO2 Regulator - Tool-Free - Dual Gauge (4.5bar PRV & 65psi Gauge)

The MK5 Dual Gauge Regulator by KegLand now comes in a tool-free design with a heap of new features.

Latest Features

1. One handed tightening to the Cylinder. No spanner / wrench is required to attach the Regulator to your CO2 Cylinder. You can easily attach it with the nut-hand-wheel with one hand. This is due to a new spigot seal design that easily compresses without risk of damaging the seal or leaking. 

2. Self servicing maintenance without the need for a vice or specialised equipment. Now with the regulators internals being shrunk down and accessible from the back plate. You can now easily undo the area with the regulator knob that has an M8 Hex / Allen key head and clean out your regulator if you have a contaminant in there. 

3. Output with Check Valve, Ball Valve & Integrated 8mm duotight push in.

4.  Triple scale Class 2.5 Gauges in kPa, Bar and PSI  (+-2.5% Accuracy).

5.  Brand new seat cap assembly design. The new seat cap is made of ultra high molecular polyethylene. That basically means from hardcore use and abuse that us homebrewers give regulators like force carbonating. The seat cap that is bouncing up and down is less likely to scratch and create brass finings that could otherwise cause pressure creep down the line from an internal contaminant going upstream.

6. Stronger Steel Gauges made from thicker steel.

7. Colour Coded PRV valves.  This unit comes with a 65psi Green PRV. It does not come with a Red 35psi or Grey 100psi PRV

8. M6 Mounting Holes for easy Mounting. Please note, you will need to remove the nut-wheel as it will foul when mounting flat.

From: Kegland

The Precision Plus CO2 Regulator is the perfect choice for ensuring precise and consistent control over the CO2 levels in your beverage dispensing system. With a sleek chrome-plated finish, this regulator not only performs exceptionally but also adds a touch of elegance to your setup.

Designed with a robust construction and advanced features, it guarantees reliability and durability for both commercial and home use. The regulator comes equipped with a 0-60 PSI outlet connection, and a 0-3000 PSI inlet connection, making it versatile for various applications. Additionally, the double inlet filter with 200 microns and 100 microns capacity ensures clean and smooth operation.

The Precision Plus CO2 Regulator is ideal for a variety of beverage dispensing systems, including beer kegerators, soda machines, and other CO2-powered applications. It ensures that your beverages are carbonated to perfection, offering consistent performance whether in a commercial bar or restaurant setting or for home use. The robust construction and precise control make it a reliable choice for anyone looking to maintain optimal CO2 levels in their beverage dispensing system.

• Chrome-plated finish for durability and aesthetics
• Single outlet design simplifies CO2 distribution
• 0-60 PSI outlet connection allows for accurate CO2 pressure adjustments
• 0-3000 PSI inlet connection handles high-pressure inputs effectively
• Double inlet filter (200 microns/100 microns) provides superior filtration

Now with 8mm push-fit outlet.

This regulator comes with a tamper evident cap. Tamper evident caps help ensure consistent dispensing pressure, which is crucial for quality control in beverage dispensing. Prevent unauthorised or accidental manipulation of the pressure settings on your CO2 system. Improperly adjusted CO2 pressure can lead to over-carbonation or under-carbonation of beverages, which can affect taste and safety. It is quick and easy to install the tamper evident cap by following these steps.

From: Krome Dispense

A Type 10 fitting with 1/4" thread nut and stem for the MK4 Regulator.

This nut and stem suits Oxygen, Argon, and Helium tanks. The MK4 Regulators comes standard with a Type 30 thread which is suitable only for CO2 cylinders. Remove the existing Type 30 Nut and Stem and replace with the Type 10 to fit to Oxygen, Argon or Helium cylinders. We recommend using a ratchet gun or socket set to do this.

Note: Regulator not included.

A nylon regulator washer to fit the range of MK regulators (MKI, MKII, MKIII & MK4). Plumbers tape not required. Simply screw your regulator in tightly, the washer will make a complete seal. 

From: Kegland

Replacement Soft Red Easy-Tight Washer for the MK5 Kegland Regulator only.

Specifications:

17.5mm x 11mm x 3.5mm

Not suitable for any other regulator on the market.

From: Kegland