Search results
257 results
Search results
EVABarrier Red Lightshield 5mm ID x 8mm OD - 12m Roll
Red semi-transparent EVABarrier for kegging setups. Easily see your gas lines in minimal light without confusion.
This high quality beer line will keep your previous beverage in it's best possible condition in the process.
This 5mm size is the one of the most common sizes for kegerator setups.
When using this 5mm ID size you will need to use about 3-4 meters of beer line to get adequate flow resistance between your keg and tap for most kegerator setups.
Pressure Rating (with 1.5x safety factor)
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)
This new Red EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.
Red Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings. The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.
Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier. The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss. So your beer will stay fresher for longer and not loose carbonation like other beer line types. In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period. EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.
Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable. This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.
From: Kegland
This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla.
It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel.
Diameter: approx. 66mm Heigh: approx. 300 mm.
From: Kegland
This handy PCO38 Tapping Head assembly is a great way to get into kegging. Using standard home brew ball lock disconnects this is convenient, light weight, robust and useful for wine, cocktails, beer, and other beverages.
This PCO38 tapping head assembly has been designed to suit standard PCO38 bottle necks.
The PCO38 keg system is a inexpensive keg system that utilises quality engineering plastics and efficient injection stretch blow mould processes to manufacture economical kegs and tapping heads for both home brewing and commercial beers.
This particular tapping head kit comes included with 2.5bar pressure relief valve, liquid and gas ball lock posts and dip tube.
The plastics used in the tapping head can withstand a wide range of chemicals used in the brewing industry and relatively high temperatures (over 100C).
NOTE: The keg shown in the photos is not included.
From: Kegland
Stainless Steel gas disconnect with MFL fitting for ball lock corny kegs.
Made from 304 grade stainless steel, these keg connectors are extremely reliable and robust.
From: Kegland
Tired of sucking air when transferring from your Fermzilla or Kegmenter? Or pulling air instead of the sweet nectar in your keg with a floating diptube. This is the solution!
Upgrade your setup with this fantastic Gen2 weighted filter! Constructed from durable HDPE and premium 304-grade stainless steel, it's built to withstand boiling and is compatible with most cleaners.
The clever 10g weighted end means no more fiddling with stainless nuts in your filter – just replace your old filter and enjoy consistent liquid draw. Finally, no more sucking up air! This Gen2 filter keeps your floating dip tube reliably below the surface.
The 304 stainless 80 mesh provides optimal filtration for hops and most solids without the frustration of frequent blockages.
If you own a FermZilla or stainless Kegmenter, this is a must-have addition!
From: Kegland
Type 30 Adaptor for Mini duotight Regulator - Suits 2-6kg Cylinders.
Want to take a huge amount of CO2 but pack as light as possible? Grab a Mini Duotight Regulator and this handy little adapter to be able to attach it to any Type 30 Cylinder (CO2). Meaning you can pour between 400 and 1000L of beer whilst on the move!
Taking your kegs on the go has never been this easy!
This adapter includes the nylon wash, ensuring a sound seal to the cylinder.
Simply thread the adapter onto your Mini duotight Regulator, or the 360 Core Actuator Regulator, then onto your 2-6kg CO2 cylinder and you're good to go!
From: Kegland
Mini Core 360 Adaptor for 74g Canister/Bulb (G1/2 Male x 5/8-18UNF Female).
This adaptor for the Core 360 Mini Regulator will allow you to use the oversized disposable 74gram co2 bulbs so you can take your keg system anywhere.
The oversized 74gram CO2 bulbs are large enough to dispense almost a whole 19L keg of beer so they are a really great choice for portable keg systems.
NOTE: The regulator itself and 74grams bulbs need to be purchase separately.
From: Kegland
Replacement Low2 keg lid o-ring seal for corny keg lids. Suitable for any 19L, 9.5L corny keg - ball lock or pin lock.
Also suits FermZilla 2" tri-clamp pressure lids.
Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.
From: Kegland
Nukatap Mini Flow Control Set
This bundle combines the four items needed for a standard ball lock set up, including a Duotight 8mm Flow Control Ball Lock Disconnect for fine flow rate control.
Includes:
- Nukatap Mini
- NukaTap Mini Self Closing Tap Spring
- NukaTap Mini - Duotight Adaptor - 8mm
- Keg Connector - Duotight Flow Control - 8mm Liquid
Nukatap Mini - Mini Design - Ideal Flow Rate for Small Systems
Most conventional beer taps are designed with a 10mm diameter nozzle/spout so you can pour pint in just over 10sec. This type of flow rate is great for high turnover bars and commercial venues but this high flow rate requirement is not not necessary or desirable for all applications. For compact portable systems, or for home brew draft systems, a slower flow rate is easier to control the flow and further reduces foaming issues due to the low liquid volume stored in the tap body.
This Nukatap mini is also more ideal for pouring smaller doses. For example cocktails where 150-250ml of liquid is dispensed is difficult to control with a high flow rate tap. For portable systems this tap and FC ball lock disconnect assembly is small enough to literally put in your pocket making it ideal for mini keg setups that you want to be portable or that you want to easily fit inside a domestic fridge where space is tight.
Forward Sealing
Forward sealing taps are absolutely the way to go when it comes to beer taps. The issue with rear sealing taps is that beer dries up on the tap piston. This is not sanitary and as more and more beer dries up in these components the tap can almost glue complete shut causing damaged seals or broken handles (this is particularly the case if it's left for some time to dry out with beer inside). These older legacy design still exist probably due to poor education. The forward sealing design do not have this problem and the tap drains out completely with no beer drying up on the mechanical moving parts in the same way. This makes the tap more sanitary and reduced maintenance. In may instances the price is similar so there is no reason to use a poorly designed rear sealing tap. All Nukatap taps are forward sealing.
Laminar Flow
Just like the Nuktap SS and Nukatap FC, the Nukatap Mini has been designed with laminar flow in mind. Laminar flow is critical for a beer tap as it means you will pour the beer with minimal foaming and a substantial reduction in wastage. Think about how many times a beer tap opens and closes in it's lifetime - 1000 or maybe 10,000 times? Laminar flow saves wasted beer in excessive foam and the better laminar flow easily pays for itself in a reduction in lost beer. Extensive modeling has been done on this Nukatap design to improve laminar flow.
Integrated Seals that are Indestructible and more Sanitary
Unlike other designs, the Nukatap Mini body is made from POK making it strong, robust and able to be autoclaved. The seals are also over-molded from Santoprene® making them hard wearing so they will literally last for the lifetime of the tap without the need for replacement. Santoprene® and POK both have excellent resistance to chemicals such as caustic soda, peroxide, phosphoric acid, lactic acid, citric acid, acetic acid, and all common chemicals sold and used in the beverage industry. The seals internally in are over-molded meaning NO fissures or cracks exist for bacteria, crud or yeast to hide.
Superior First Pour Foam Due to Low Thermal Mass and Conductivity
First pour foam is an issue caused by a warm tap body. For most taps to pour well it's important to dispense enough beer to cool the tap body down before the tap will pour well. In addition to this the conductivity of the tab body also makes this worse so insulative materials simply work better than conductive materials. The Nukatap mini not only has very low thermal mass but is also highly insulative being made mostly from Santoprene and POK. The combination of these two factors in conjunction with superior laminar flow makes for the lowest "first pour foam" effect out of any tap ever produced.
Long Shank Alternative (Sold separately in Duotight design)
Most conventional beer taps require a large 22mm hole to be drilled through the wall of your keezer/cooler/wall. Traditional long shanks also generally have a large volume of liquid that sits inside the wall unrefrigerated which is not ideal. This new long shank alternative is designed to suit any wall thickness and greatly reduces the stagnant beer sitting in the shank itself. For walls up to 80mm thick we have provided three screws however if the wall is thicker you can also use 6 small wood screws or something similar and attach three screws from the front and 3 from the back allowing you to go into any wall type.
Another advantage of this new design is the tap will never accidentally rotate. Typically other long shank beer taps rely on the hex nut on the shank to be done up tight enough to prevent rotation but if the wall compresses (often the case with foam walls) the tap is allowed to rotate. This new design has three fixing points making it impossible for the tap to rotate accidentally as the interlocking teeth behind the collet allow you to set the angle and then do up the collet to fix the tap permanently in that position.
From: Kegland
KegLand Mini 360 Core Actuator Regulator - Sodastream & 16g & 74g Bulb Compatible
The All-New Mini 360 Core Actuator Regulator is the most versatile mini regulator on the market. It is an extremely versatile mini regulator that can be used with either a Sodastream Canister, or the smaller disposable CO2 16g bulbs.
Unlike other regulator designs this new design requires no sodastream adaptor and you do not have the issues of trying to screw the bulb or sodastream cylinder into the regulator while gas leaks everywhere. This robust, convenient and superior design is just what you need for any portable keg system.
Please note this is not compatible with the 2kg, 3.5kg or 5.0kg CO2 Cylinders.
Features:
- Core Puncturing / Actuator - Zero gas lost to screwing in bulbs or Sodastream style cylinders.
- Interchangeable ball lock disconnect orientations (e.g. 45° Premium Ball lock to 90° Stainless Disconnects)
- 6.5mm duotight compatible hose barb (6.5mm x 8mm duotight) can also suit hose and stepless clamps (e.g. 4mm ID, 5mm ID or 6mm ID hose)
- Heavily Protected Mini Guage Dial. (Also interchangeable to different ranges)
- Common Pressure relief valve compatible. (65psi Green PRV as standard, compatible with 35psi Red and 100psi Grey)
Includes:
1 x Mini 360 Core Actuator Regulator
1 x 360° 6.5mm duotight compatible hose barb
1 x 360° FFL Fitting for MFL Disconnects
1 x Port end cap
1 x 65psi Green PRV
1 x Sodastream to 16g thread bushing
Upgrade to digital:
Upgrade to a more accurate digital gauge with this gauge. This mini gauge is easier to read and has a backlight so you can also read the pressure easily in the dark.
WARNING:
Do not over tighten onto your cylinder. It is recommended that you use a spanner to hold the neck of your Sodastream cylinder while attaching and detaching the Mini 360 Core Actuator Regulator.
From: Kegland
This Push-Fit Two-Way Divider will split the gas (or beer) line on your kegging system in two, allowing you to gas two kegs at the same time.
Note that this is 10mm diameter in and out.
They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps or tools. To remove the fitting, simply push in the collet and the hose can be removed. Fits 10mm outer diameter tube.
Note: colour may vary.
A ball lock keg post with 1/2 inch male thread, used on Mytton Rodd kegs but could be used on ball valves or tri-clamp fittings with 1/2 inch thread.
From: Kegland
This pretty handy kit contails all the seals needed for both the standard Nukatap and the Flow Control Nukatap.
The majority of these seals would never normally need to be replaced, but in the event of accidental loss / extreme commercial use please replace washers with the addition of food-grade lubricant to ensure their longevity.
Please refer to the parts diagram for seal locations:
If you have not changed your seals before, it's a great idea to take a note of which seal goes where as you remove the old ones!
Includes:
- The Nuke!
- Tap Coupling Washer
- Bonnet Washer
- 2 x Cup Seal
- Nozzle Washer
Also included (unique to the FC Nukataps):
- 2 x Shaft Seals
- Flow Bonnet Damper
- Shaft Cushion
- Flow Slider Seal
From: Kegland
This Push-Fit Elbow will allow you to join beer or gas line sections on your kegging system.
Note that this is 10mm diameter in and out - if you're after 8mm, you'll find it here
They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps or tools. To remove the fitting, simply push in the collet and the hose can be removed. Fits 10mm outer diameter tube.
Note: colour may vary.
Replacement shuttles for Nukatap - Flow-Control. (Spare Part Item Numbers 11 and 12)
Please note the o-ring is included on part 12 already. A small amount of lubrication may be required.
From: Kegland
This hose fitting is made of stainless steel and connects three lengths of hose in a branch tee. The barbed fittings create a tight seal on flexible and semi-rigid hose when used with a hose clamp such as a stepless clamp.
Bore sizes usually available:
- 6.35mm (1/4")
- 4.76mm (3/16")
4L PET Oxebar Keg with Cap and Handle (PCO38 )
Keep your oxygen-sensitive beverages fresher for longer with the Oxebar Monolayer. We recommend this product for storing beer up to 3-6 months.
The new lightweight and reusable plastic kegs are brought to you by Oxebar and KegLand. Store your homebrew in a more convenient size, take it away camping or to a bbq. The new shorter profile 4L under 330mm will fit in most chilly bins or esky coolers. You can also dispense with it lying on its side.
Do not Exceed 4 Bar / 58psi or 45°C
This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19L corny kegs. The small 4L size is convenient, light weight and perfect for sharing beverages with friends.
This 4L keg is light weight, compact and has extreme oxygen barrier properties. This extremely low gas transmission means your beverage will stay much fresher for longer. Even if you do consume the beverage in a short time, that short time will have much less oxygen transmission compared to other PET kegs on the market. Suitable for carbonated and non-carbonated beverages.
This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head. The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design.
What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.
Dimensions
Diameter:155mm
Height: 325mm
Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically. This is a very simple process and it's nothing to be feared. We recommend that this container be pressure tested every 2 years up to 6 bar. The instructions for this are:
1. Remove RED prv and fit GREY prv (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water. DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar.
4. Hold the keg at 6 bar for 1 minute
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30C
From: Kegland
