Search results
257 results
Search results
Colour coded Yellow and Red Ball Lock Keg Post O-Rings. Silicone for superb malleability and spring back memory performance.
We've all been there, not looking or not thinking and trying to put a gas disconnect on a liquid post. Yes, there's a notch in it. Yes, there are words IN and OUT. But you're busy! You don't have time to go searching, it should just be in your face obvious that it's a liquid or a gas post. KegLand finally has the answer with the long awaited colour coded Gas and Liquid Post Sets Red & Yellow.
FAQ
Why not Low2 O-Rings? Aren't they supposed to be better?
There is one fundamental reason why we didn't and shouldn't use Low2 O-rings for a post. Spring-Back Memory - Leak prevention.
Low2 has a lot of memory, while silicone does not. This means that if you use a Low2 O-ring on your keg posts, keep the keg cold in the fridge, and have everything connected, then later remove and reattach the disconnects, the O-ring's memory could be slightly off unless you reseat it in exactly the same position. That misalignment can lead to a potential leak.
We use Low2 on the Hatch Lid O-Ring because its a face seal that can withstand 100's of PSI worth of pressure, and even if flattened slightly under pressure it can be reseated quite easily.
A Radial Seal (Post O-Ring) is much harder to manipulate.
All independent testing with Low2 Keg Lid O-rings was done with silicone post o-rings. So rest assured you're getting the best possible product that means less leak spots, and better chemical resistance and performance.
Comes with:
5 x Yellow Liquid In Post O-Rings
5 x Red Gas Out Post O-Rings
We would recommend applying food grade lubricant to your o-rings on a regular basis to prolong their life. Especially after deep cleaning.
From: Kegland
8mm OD Beer Line Tidy (BLT) - Beer and Gas Line Organiser.
This beer line tidy is a handle little part that will help you organise your beer and gas line inside your fridge, keezer, kegerator or cellar. Designed to suit 8mm outer diameter hosing like the 4mm x 8mm EVABarrier and 5mm x 8mm EVABarrier hosing.
Simply remove the paper and use the strong 3M adhesive to attach this beer/gas line organiser to whatever device you like.
This keeps your beer and gas plumbing neat and tidy so your draft system looks as good as it works.
From: Kegland
The posts include a 20mm long thread, an o-ring, poppet, locking nut and short dip tube. This would enable you to make a keg out of any pressure vessel if you wanted to. The assembly can also be fitted to regulators, gas manifolds and various other items.
Both Gas and Liquid posts available.
From: Kegland
High quality beer dispensing parts like this one are made of stainless steel to ensure that the taste of your beer is not compromised.
Material: stainless steel 304
From: Krome Dispense
This Tap to Keg Adapter and Coupling Nut will allow you to add a beer dispensing tap directly to your keg. Includes both adapter and faucet coupling nut.
Requires an MFL keg connector and beer tap, not included.
This Push-Fit Joiner will allow you to join beer or gas line sections on your kegging system.
Note that this is 10mm diameter in and out - if you're after 8mm, you'll find it here
They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps or tools. To remove the fitting, simply push in the collet and the hose can be removed.
Fits 10mm outer diameter tube.
Note: colour may vary.
This rigid 50mm long joiner is made from strong polypropylene. It's useful to make rigid joins with push in fittings that are dead straight. Although it's possible to make joins using short pieces of 8mm OD Evabarrier 5mm Beer Line this is far more flexible and when mounting parts to a gas board or wall its will often make things much neater if you use these instead.
The 50mm length is long enough so even after pushing right into two duotight 8mm fittings on both ends you should still have a exposed length of about 3mm so you can still relatively easily take the fittings apart later.
From: Kegland
Dimensions: 8mm OD x 6mm ID x 50mm long
The Party Pump Kit provides an easy way to dispense a commercial beer keg when you are away from electricity or don't have a CO2 cylinder.
Just put the keg in a bucket of ice and pump the beer out at your own leisure. This reliable and simple setup is easy to use and requires no power, no gas cylinder and no regulator. It's really the easiest way to dispense a keg at a party.
Features
- Easy to use
- No gas cylinder required
- No electricity required
- Plastic tap and beer line The hose comes un-assembled so you will need to assemble before use.
Note: Does not include keg coupler. Please be aware that you will need to make sure your keg coupler has the check valve installed.
Note: Beer must be drunk within 48 hrs.
From: Kegland
This Duotight Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
From: Kegland
This is the Dual Pressure MK4 CO2 Regulator - you'll find the single pressure regulator here.
Need to set two different CO2 pressures for different beers on tap? Then you'll need two regulators to do it properly. With this MK4 Dual Pressure Regulator you'll be able to screw it into your CO2 bottle and fire away with two different pressures. No need to removing the High Pressure gauge off one regulator, buying an attachment and joining the two together.
This new MK4 Model regulator has several advantages including:
1. Safer design with colour coded pressure release valves
2. Easy mounting option
3. Optional extras such as gauge guard
4. Better body design and more reliable
Now comes with Duotight 8mm push-fit fittings rather than barbs. We recommend using thread tape to ensure a good leak free seal between the Duotight MFL fitting and the regulator.
From: Kegland
Note: CO2 bottle not included.
Gas (grey or white) connector with barb for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Ball Lock Keg Liquid Jumper Post - Double Ended Corny Post
We've seen some nifty tricks of how people wash their Kegerator lines if they have multiple taps. This compact solution is going to make that routine cleaning day a breeze without having to swap disconnects to the cleaning keg/bottle or dismantling multiple ball locks. Just jump on the jumper post.
This double ended cornelius post does not have a spring / poppet. It just has a piece of bar that activates the ball lock disconnect wide open.
This double ended post will only work with liquid Ball Lock posts.
Please note it is a single piece that cannot be undone from the middle.
From: Kegland
Gas Free Ball Lock Line Cleaning Kit
Are you ever in a situation where you don't want to unhook your gas line from your kegs, or have ball lock disconnects that you need to clean over at the sink but don't want to take your gas line all the way over there? Well, Kegland thought of a better way. Why not fill a PET Bottle with your cleaner / sanitiser and pump it without gas!
This little device can also be used as a mini party keg without a gas source (should be consumed well within 24 hours of pumping). BYO Liquid disconnect, hose and picnic tap.
Contains:
1 x KegLand Yellow Carbonation Cap
1 x KegLand PCO Tee Piece (Female x Male x Male)
1 x Mini Yellow Hand Pump
1 x 30cm Piece of EVABarrier Line 5mm ID x 8mm OD (can be stretched for larger PET bottles)
From: Kegland
This push in fitting will fit 8mm outer diameter tubing, while the thread on the other end will suit:
- MFL ball lock disconnects
- MKIII and MK4 regulators with MFL output
- Other fittings with MFL thread
No clamps necessary, but we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
Gas (grey or white) connector with MFL thread for ball lock corny kegs.
This is a premium plastic ball lock connector designed with the highest tolerances and quality control standards. These can be easily distinguished by the two toned cap on top of the disconnect.
Type 30 - MK5 CO2 Regulator - Tool-Free - Dual Gauge (4.5bar PRV & 65psi Gauge)
The MK5 Dual Gauge Regulator by KegLand now comes in a tool-free design with a heap of new features.
Latest Features
1. One handed tightening to the Cylinder. No spanner / wrench is required to attach the Regulator to your CO2 Cylinder. You can easily attach it with the nut-hand-wheel with one hand. This is due to a new spigot seal design that easily compresses without risk of damaging the seal or leaking.
2. Self servicing maintenance without the need for a vice or specialised equipment. Now with the regulators internals being shrunk down and accessible from the back plate. You can now easily undo the area with the regulator knob that has an M8 Hex / Allen key head and clean out your regulator if you have a contaminant in there.
3. Output with Check Valve, Ball Valve & Integrated 8mm duotight push in.
4. Triple scale Class 2.5 Gauges in kPa, Bar and PSI (+-2.5% Accuracy).
5. Brand new seat cap assembly design. The new seat cap is made of ultra high molecular polyethylene. That basically means from hardcore use and abuse that us homebrewers give regulators like force carbonating. The seat cap that is bouncing up and down is less likely to scratch and create brass finings that could otherwise cause pressure creep down the line from an internal contaminant going upstream.
6. Stronger Steel Gauges made from thicker steel.
7. Colour Coded PRV valves. This unit comes with a 65psi Green PRV. It does not come with a Red 35psi or Grey 100psi PRV
8. M6 Mounting Holes for easy Mounting. Please note, you will need to remove the nut-wheel as it will foul when mounting flat.
From: Kegland
This Duotight Push-Fit Tee - 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
Note: colour may vary.
From: Kegland
This model of carbonation cap does everything that regular carbonation caps do but with several added features.
The post on this unique carbonation cap has been machined to fit both the black/liquid and grey/gas ball lock disconnects. This carbonation cap also includes a barb-tail on the underside so you can attach beer line to act as a dip tube.
This allows the carbonation cap to be used in several different ways including:
1. Carbonating
2. Cleaning your beer lines
3. Using it to counter pressure bottle fill PET bottles
From: Kegland
This adapter is suitable for the Mini Duotight Regulator to fit a threaded Sodastream cylinder.
Please note: The adaptor can only engage the cylinder via the round knob. It cannot retract / disengage. Always use two spanners / adjustable wrenches when attaching this to your sodastream.
Specifications:
5/8' 18TPI 18UNF male to G1/2 female
From: Kegland