This clear tubing has an internal diameter of 7mm and an external diameter of 11mm, and comes in a 3 metre pack

Silicone is a superior material to traditional vinyl tubing. Silicone is food-safe, heat-resistant, more flexible and easier to use. 

These washers are compatible with any 1/2 BSP plumbing hardware.

The silicone rubber in these washers is suitable for temperatures up to 250°C.

This is made from food grade silicone and will not perish like some other rubber washers.

Dimensions: 21mm(ID) x 31mm(OD) x 2mm (thickness)

From: Kegland

The Smell Eliminator Kit completely eliminates ALL smells from the fermentation process for both beer and spirits.

Includes everything you need to attach to a standard fermenter with airlock (airlock not included).

Now you can ferment wherever is best to maintain your desired fermentation temperature without worrying about the smell.

The carbon cartridge for the Smell Eliminator Kit is made from a specially designed dense carbon block, which will last for approximately 5 brews or washes. Will not filter liquids.

Made from 304 stainless for hygiene and will last a lifetime.

Instructions: The Smell Eliminator Kit

A replacement carbon cartridge for the Smell Eliminator Kit. Made from a specially designed dense carbon block, it will last for 5 brews or washes. Will not filter liquids.

This easy to use SodaStream Cylinder Filling Adaptor will enable you to fill your own CO2 from your larger bulk cylinder into smaller SodaStream cylinders. An easy and inexpensive way to fill your own Sodastream Cylinders at home at a fraction of the cost of getting the refills from your local store.

Note: Does not fit the latest Sodastream cylinders, only older cylinders. The CO2 Cylinder and Sodastream cylinder in the photos is not included.

When using, be sure to following these important points:

1. That the seals goes in the correct location. So when the SodaStream Filling Adaptor arrives, please make sure to use the correct seal in the correct side.

2. Make sure to put the Sodastream cylinder on the correct side. The SodaStream cylinder thread can actually fit both sides of this adaptor, but the CO2 cylinder only fit's into the ROUND SIDE. As a result you MUST put the Sodastream cylinder into the HEXAGONAL SIDE. (as shown in image)

Introducing the all new Brew Bucket 2.0

Nearly a decade after the Brew Bucket was first produced, Ss Brewtech challenged the Ss Engineering Team to pair some of the newest technologies with the original design.

Replacement Lid Seal for SS Brewtech Brew Buckets and Chronicals; made from brewer's grade silicone.

These also fit the FTSs lids at the matching size.

From: Ss Brewing Technologies

The Ss Tri-Clamp Brew Kettle is constructed from 304 stainless steel and features an aluminium core tri-clad bottom to foster even heating and minimise the risk of scorching and allow for the use of induction heating.

Tri-Clamp ports have long been the standard in professional brewing, and for a good reason, they're quick, sturdy, and sanitary. The Ss Tri-Clamp Brew Kettle now brings this pro-level feature to the home brewer in an affordable package.

The sturdy riveted silicone-coated handles are now located on the front and back for easy moving and dumping of the kettle while also allowing for tighter brew stand setup. Just like the original Ss Brew Kettle, the tri-clamp version features an integrated trub dam into the dip tube to minimise the pickup of trub and hop material during knockout. The result is much clearer wort making its way into the fermenter.

Features:
- Tri-Clad bottom
- Sanitary tri-clamp ports
- Sturdy riveted silicone coated handles
- 3 piece tri-clamp ball valve with trub dam pick-up tube
- Lid designed to hang on side of handles
- Etched volume markings gals/litres
- Induction burner compatible

Available in these sizes:
- 38 Litre (10 Gal)
- 57 Litre (15 Gal)

Ss Brewtech recommends using Trisodium Phosphate (TSP) (sold separately) for initial cleaning to remove oils, grease and any manufacturing residue.

Stainless steel worm style hose clamp which fits a variety of hose types.

This hose clamp features a butterfly/key type adjustment tab which makes it easier to grip onto and tighten/loosen the clamp without the need for any tools.

If a larger diameter is required then multiple worm type hose clamps can be attached together.

Sizes available: 

• 14-25mm
• 21-38mm

From: Kegland

This hose fitting is made of stainless steel and connects three lengths of hose in a branch tee. The barbed fittings create a tight seal on flexible and semi-rigid hose when used with a hose clamp such as a stepless clamp. 

Bore sizes usually available:
- 6.35mm (1/4")
- 4.76mm (3/16")

A quality mash paddle is an essential piece of equipment for all-grain brewers. 

This high quality stainless steel mash paddle is approximately 61cm long and will make stirring the mash and avoiding dough balls a much simpler task. Avoiding the formation of dough balls during the mash is important to ensure the full extract potential of the mash is achieved. 

The paddle is also perfect for all other stirring duties and may even be used to knock down the hot break at the beginning of the boil.

The Pluto Beer Gun has become an iconic beer dispensing tool used throughout the industry. It is indestructible and, apart from the seals, it is entirely machined out of stainless steel and you can feel it in the weight and feel when you pick it up. The accurately machined bore gives smooth laminar beer flow for foam free dispensing.

This is the premium, full stainless steel version, and comes with a barb that suits standard our beer line.

Stainless Steel Quick Disconnect - Male to 13mm (approx. 1/2") Barb. Fits our Female Quick Disconnect.

Made from 304 stainless steel.

Stainless Steel Quick Disconnect - Male to 8mm Barb. Fits our Female Quick Disconnect.

Made from 304 stainless steel.

A stainless steel shank for your beer tap, with a bore size of 4.76mm (3/16").

Available in three sizes with shank lengths of: approx. 79mm, 105mm, and 130mm

Note there is no tail piece included but a separate tail piece, nut and washer are offered as additional options.

Alternatively a Duotight 8mm - 5/8" Thread can be used.

Length: approx. 79mm (3-1/8"), 105mm (4-1/8"), or 130mm (5-1/8")
Usable length: approx. 50mm, 65mm or 80mm
Bore size: approx. 4.76mm (3/16")
Material: Stainless Steel
Made by: Krome Dispense

Short Shank - Stainless Steel (Duotight compatible).

This is a high quality stainless steel spoon with long handle approximately 53cm in length.

It is well suited to all stirring duties and can be used to take samples from the mash tun or boil kettle. 

It is made of heavy-duty stainless steel so it will not warp due to heat, and is corrugated to help prevent it from bending.

The advantage of these clamps is that the inner circumference is free of any steps or gaps, making them very useful on gas and beer lines for leak proof lines. 

Available in the following sizes:

• 10mm
• 10.5mm
• 11.9mm
• 13.3mm
• 17mm

You will need a Clamp Crimper tool for installation.

Colour liquid crystal thermometer to place on to your fermenter. Has a range of 10℃ - 36℃ going up in 2℃ increments.

A submersible pump, 2000L/H, 3.2m head, which is the same as what is supplied with the Bucket Blaster, if you need a replacement. 

From: Kegland

A sugar measure for:

1. 330ml bottles
2. 500ml bottles
3. 750ml bottles

A replacement mecanicco swing lid for the 5L Glass Jar Demijohn with mecanicco Swing Lid. Not suitable for the 5L Glass Jar Demijohn with Screw Cap/Lid.

Useful for measuring small ammounts of additives.