Sort by:
Replacement Soft Red Easy-Tight Washer for the MK5 Kegland Regulator only.
Specifications:
17.5mm x 11mm x 3.5mm
Not suitable for any other regulator on the market.
From: Kegland
A replacement seal for Kegland D-Type keg spears.
From: Kegland
Replacement Silicone Seal for 65L BrewZilla Boiler Extension (24L).
You'll find the Brewzilla Boiler Extension Kit here.
From: Kegland
A rubber stopper (bung) with a diameter of approximately 50mm across the top, tapering to a diameter of approximately 41mm at the bottom. Fits the 23 Litre Plastic Carboy and 11.5 Litre Plastic Carboy.
Worn down your washers and seals from filling oodles of sodastream bottles? Then you may want to purchase some extra washers and o-rings
Includes:
1 x Nylon Regulator Washer
1 x Sodastream Black Washer
5 x Bleed Valve O-Rings
Please note these items are not sold individually, they are sold as a seal kit. Seal colour may vary.
From: Kegland
Seal Kit for both the Ball Lock and Pin Lock type Cornelius kegs.
Includes:
What is Low2?
Low2 O-Rings are the new golden yellow standard of homebrew keg parts from Kegland. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.
From: Kegland
Black Short Shank - Stainless Steel - 6.5mm (1/4'') tail suits Duotight 6.5mm Reducer.
Black stainless steel duotight compatible short shanks are the perfect addition to your black phantom font tower. Couple this with the black Nukatap Stealth Bomber for the ultimate sleek and stealthy draught setup for your kegerator or home bar.
If you still want to use a stepless clamp. Good news! You still can, just use needle nose pliers, boiling water and a positive mindset to get the hose over the barb.
These short shanks are suitable to attach taps to our kegerator fonts, and can be used to replace the short shank on any 3" diameter tower.
Item Includes:
- Blank Stainless Steel Shank with a 6.5mm duotight compatible barb
- Ring collar
- Nut
- Right angle font collar to suit font
- Shaped internal collar to suit font
NOT INCLUDED but highly recommended for 8mm OD beer line: Duotight - 6.5mm x 8mm Reducer
Common tips for cutting your beer hose for optimum flow resistance:
EVABarrier Hose - 4mm ID x 8mm OD = Reccomended 1.5m to 2.1m
EVABarrier Hose - 5mm ID x 8mm OD = Reccomended 2.0m to 3.2m
From: Kegland
A gas shut off valve (ball valve) with built in return check valve and MFL nipple.
Material: Chrome Plated Brass Thread: 1/4" x 1/4" MPT
From: Krome Dispense
Braided Reinforced Heavy Duty Silicone Hose - 10m Roll (12mm ID x 20mm OD).
Properties:
Odorless, tasteless and inert
Good Electrical and weatherability properties
Resists UV, Ozone, gases and moisture
Features:
Working Temperatures -60°C ~ 260°C
Working Pressure: 58-580 psi
Applications:
Commercial brewery hot and cold side transfers
Length: 10m
From: Kegland
Silicone hose for liquid transfer. It is resistant to constant high temperatures and will handle temperatures above boiling point, and has excellent chemical resistance. The soft silicon is easy to work with and seals very well.
Please note that this tube should not be used for pressure above 15psi (such as mains water pressure), and has a burst pressure of around 30psi.
Price is per metre unless specified.
This clear tubing has an internal diameter of 7mm and an external diameter of 11mm, and comes in a 3 metre pack
Silicone is a superior material to traditional vinyl tubing. Silicone is food-safe, heat-resistant, more flexible and easier to use.
These washers are compatible with any 1/2 BSP plumbing hardware.
The silicone rubber in these washers is suitable for temperatures up to 250°C.
This is made from food grade silicone and will not perish like some other rubber washers.
Dimensions: 21mm(ID) x 31mm(OD) x 2mm (thickness)
From: Kegland
The Smell Eliminator Kit completely eliminates ALL smells from the fermentation process for both beer and spirits.
Includes everything you need to attach to a standard fermenter with airlock (airlock not included).
Now you can ferment wherever is best to maintain your desired fermentation temperature without worrying about the smell.
The carbon cartridge for the Smell Eliminator Kit is made from a specially designed dense carbon block, which will last for approximately 5 brews or washes. Will not filter liquids.
Made from 304 stainless for hygiene and will last a lifetime.
Instructions: The Smell Eliminator Kit
A replacement carbon cartridge for the Smell Eliminator Kit. Made from a specially designed dense carbon block, it will last for 5 brews or washes. Will not filter liquids.
This adapter allows a SodaStream cylinder to attach to a CO2 regulator for your kegging set up. It is ideal for low volume CO2 use and avoids renting or purchasing a larger CO2 cylinder. This is the deluxe version, with pin adjustment which makes the SodaStream cylinder adaptor significantly easier to use.
Normal SodaStream adaptors require an alan key to adjust the pin height and depending on how worn out your seal is you may need to adjust this pin periodically and it may leak gas when connecting and disconnecting from your regulator. This new SodaStream adaptor is significant better designed with the handy thumb screw on the side of the unit allowing you to eliminate cumbersome adjustment and it also gives you the ability to turn off and on the gas flow.
This adaptor is used if you have a SodaStream Cylinder and wish to use a conventional Type 30 Regulator with it, perhaps for bbq or a picnic and you don't want to carry your 4.5kg or 2.6kg Gas Cylinder, as it will enable you to make a handy portable system.
Note: Does not include regulator or gas canister.
If you need to change the o-rings on this device here is the instruction manual on how to do this.
This easy to use SodaStream Cylinder Filling Adaptor will enable you to fill your own CO2 from your larger bulk cylinder into smaller SodaStream cylinders. An easy and inexpensive way to fill your own Sodastream Cylinders at home at a fraction of the cost of getting the refills from your local store.
Note: Does not fit or work with the latest Sodastream cylinders, only older cylinders. The CO2 Cylinder and Sodastream cylinder in the photos is not included.
When using, be sure to following these important points:
1. That the seals goes in the correct location. So when the SodaStream Filling Adaptor arrives, please make sure to use the correct seal in the correct side.
2. Make sure to put the Sodastream cylinder on the correct side. The SodaStream cylinder thread can actually fit both sides of this adaptor, but the CO2 cylinder only fit's into the ROUND SIDE. As a result you MUST put the Sodastream cylinder into the HEXAGONAL SIDE. (as shown in image)
Replacement Lid Seal for SS Brewtech Brew Buckets and Chronicals; made from brewer's grade silicone.
These also fit the FTSs lids at the matching size.
From: Ss Brewing Technologies
Stainless steel worm style hose clamp which fits a variety of hose types.
This hose clamp features a butterfly/key type adjustment tab which makes it easier to grip onto and tighten/loosen the clamp without the need for any tools.
If a larger diameter is required then multiple worm type hose clamps can be attached together.
Sizes available:
From: Kegland
This hose fitting is made of stainless steel and connects three lengths of hose in a branch tee. The barbed fittings create a tight seal on flexible and semi-rigid hose when used with a hose clamp such as a stepless clamp.
Bore sizes usually available:
- 6.35mm (1/4")
- 4.76mm (3/16")
A stainless steel immersion chiller is a great piece of equipment for all-grain and extract brewers to cool the wort at the end of the boil. It is immersed into the boiling wort at least 10 minutes before the end of the boil (this will help to sanitise the chiller, although it should be clean before being used) and attached to a cold water source.
When ready to cool the wort, turn on the cold water and it will flow through the immersion chiller and cool the wort.
To increase the rate at which the wort cools you can stir the wort to create a whirlpool. This will cause more of the wort to come into contact with the chiller and cool the wort faster. Make sure to sanitise whatever you use to stir the wort.
You could also use a pump (such as the MKII 25w High Temp Magnetic Pump) to create a whirlpool immersion chiller; made popular by award winning American home brewer Jamil Zainasheff. Here is a link to Jamil's site, Mr Malty, with more details.
An immersion chiller can also be used to pre-chill the cooling water. Just submerge the immersion chiller in an ice bath to to pre-chill the water that ultimately flows into another immersion chiller in the wort. This can be particularly helpful during summer when the groundwater temperature increases.
This chiller comes complete with a garden hose fitting on one end to connect to your garden or kitchen tap, and clear vinyl tubing.
Specifications
Material: 304 grade stainless steel
Diameter: 3/8"
Length: 25 feet (around 7.5m)
Outside diameter of coil: approx. 250mm
From: Krome Dispense
A quality mash paddle is an essential piece of equipment for all-grain brewers.
This high quality stainless steel mash paddle is approximately 61cm long and will make stirring the mash and avoiding dough balls a much simpler task. Avoiding the formation of dough balls during the mash is important to ensure the full extract potential of the mash is achieved.
The paddle is also perfect for all other stirring duties and may even be used to knock down the hot break at the beginning of the boil.
The Pluto Beer Gun has become an iconic beer dispensing tool used throughout the industry. It is indestructible and, apart from the seals, it is entirely machined out of stainless steel and you can feel it in the weight and feel when you pick it up. The accurately machined bore gives smooth laminar beer flow for foam free dispensing.
This is the premium, full stainless steel version, and comes with a barb that suits standard our beer line.
Stainless Steel Quick Disconnect - Male to 13mm (approx. 1/2") Barb. Fits our Female Quick Disconnect.
Made from 304 stainless steel.
Stainless Steel Quick Disconnect - Male to 8mm Barb. Fits our Female Quick Disconnect.
Made from 304 stainless steel.
A stainless steel shank for your beer tap, with a bore size of 4.76mm (3/16").
Available in three sizes with shank lengths of: approx. 79mm, 105mm, and 130mm
Note there is no tail piece included but a separate tail piece, nut and washer are offered as additional options.
Alternatively a Duotight 8mm - 5/8" Thread can be used.
Length: approx. 79mm (3-1/8"), 105mm (4-1/8"), or 130mm (5-1/8")
Usable length: approx. 50mm, 65mm or 80mm
Bore size: approx. 4.76mm (3/16")
Material: Stainless Steel
Made by: Krome Dispense
Short Shank - Stainless Steel (Duotight compatible).
These short shanks are suitable to attach taps to Kegerator fonts. They can be used to replace the short shank on any 3" diameter tower. If you have received this in your kegerator package and still want to use a stepless clamp. Good news! You still can, just use needle nose pliers, boiling water and a positive mindset to get the hose over the barb.
Item Includes:
NOT INCLUDED but highly recommended for 8mm OD beer line: Duotight - 6.5mm x 8mm Reducer
Common tips for cutting your beer hose for optimum flow resistance:
EVABarrier Hose - 4mm ID x 8mm OD = Reccomended 1.5m to 2.1m
EVABarrier Hose - 5mm ID x 8mm OD = Reccomended 2.0m to 3.2m
From: Kegland
This is a high quality stainless steel spoon with long handle approximately 53cm in length.
It is well suited to all stirring duties and can be used to take samples from the mash tun or boil kettle.
It is made of heavy-duty stainless steel so it will not warp due to heat, and is corrugated to help prevent it from bending.
The advantage of these clamps is that the inner circumference is free of any steps or gaps, making them very useful on gas and beer lines for leak proof lines.
Available in the following sizes:
You will need a Clamp Crimper tool for installation.
