Colour liquid crystal thermometer to place on to your fermenter. Has a range of 10℃ - 36℃ going up in 2℃ increments.

A submersible pump, 2000L/H, 3.2m head, which is the same as what is supplied with the Bucket Blaster, if you need a replacement. 

From: Kegland

A sugar measure for:

1. 330ml bottles
2. 500ml bottles
3. 750ml bottles

A replacement mecanicco swing lid for the 5L Glass Jar Demijohn with mecanicco Swing Lid. Not suitable for the 5L Glass Jar Demijohn with Screw Cap/Lid.

Useful for measuring small ammounts of additives.

Tail Piece for your dispensing system that provides a 1/4" MFL connector instead of a barb. Fits nicely with our hex nut. You may also need a neoprene washer.

From: Krome Dispense
Material: 304 grade stainless steel

Screw-in tap for use with Handcraft Supplies 30L Wide Mouth Fermenter. Simply screw the tap in the pre-drilled hole at the bottom of the fermenter before filling the fermenter with your ingredients. Mangrove Jack's Silicone Hose 100mm is required to connect the tap to a brew bottler. Not compatible with sediment reducer.

The MFL Tap Shank Adapter is what you need to connect your draft tap directly to your MFL disconnect. These allow you to make a very compact portable setup.

We recommend using one of the Flow Control Nukatap with this adapter as this provides some restriction of the flow but they will also work with Intertap, Nukatap and other brands of taps. A nylon washer is also recommended between the disconnect and the shank adapter.

Please bear in mind that due to the compact size there is not enough space to accommodate an auto spring return so it is not compatible that setup.

Note: does not include tap or disconnect.

From: Kegland

Temp Twister Pump Kit with Return Line and Clamp.

If a glycol chiller is a bit out of reach at the moment, but you want to use the Temp Twister in your Kegmenter or FermZilla, this little product can help you on your way to cool your fermenter. Simply submerge the pump in a large bucket with water and ice.

The more insulation you give your fermenter and keep it at a relatively stable temperature the better. We suggest using this in conjunction with a temperature controller.

Parts List:
1 x 1.2m Length of Insulated 6mm x 9mm EVABarrier Hose
1 x 1.2m Length of 6mm x 9.5mm hose (return line back to the bucket) (colour may vary)
2 x 9.5mm duotight Elbows (For temp twister)
1 x Temp Twister 12v Pump and power supply

From: Kegland

The Ultimate Growler is made from 304 Stainless Steel that is completely impervious to oxygen and sunlight (UV) meaning your precious liquid is in the absolute best storage container possible.

The Growler also comes with double wall vacuum insulation helping to keep your beer cold for hours.

This is the new improved MK2 model with new lid design. This new MK2 model is more robust and more reliable than the previous growler design.

Most screw top growlers struggle to hold the pressure required to keep beer fresh and carbonated. The Ultimate Growler comes with a spring wired lid capable of holding up to 40psi.

You can also turn your Ultimate Growler into a mini keg with the:

• Beer Growler Draft Kit
• Mini CO2 Regulator - Mangrove Jack's Portable CO2 Kit or Regulator - Mini 360 Core Actuator
• CO2 Cartridges

Features:

• 304 Stainless Steel
• Double Wall Vacuum Insulated
• Sprung Wire Lid
• 2L capacity

A bi-metal weldless thermometer with glass face. Ideal for fitting to your mash tun, hot liquor tank or kettle.

Features:
- Calibration screw so you can fine tune the temperature
- 304 stainless steel housing and probe
- ½” BSP thread and includes silicon and stainless steel washers.
- Temperature range -5C to 100C customised for brewing

Includes a slimline nut and 2 x silicone seals plus a stainless washer.

From: Kegland

Thermometer With Clip - a multi-purpose thermometer you can use when brewing beer, heating milk for cheese making, or frothing milk for coffee.

This Thermometer With Clip has a long stem and a clip that you can use to attach the thermometer to the side of your equipment. 

The thermometer is made of stainless steel that is durable and corrosion-resistant. The dial is large which makes it easy to note the reading.

Probe length: 125mm

Temperature range: 0℃ - 110℃

From: Krome Dispense

A stainless steel, 1/2" thread, weldless thermowell (takes any probe up to 7mm ID).

This thermowell works great with any kegmenter, keggle, brew pot, boiler and various other brewery hardware to get an accurate core temperature of your vessles.

This thermowell has a 7mm bore, so it's ideally suited to any probe type up to 7mm.  Most probes are 6.5mm or smaller in diameter meaning they will fit nicely into this well.  It's ideal for the RAPT Temperature controllers.

This is a weld free design so all you need to do is drill a 20mm hole and file this out a fraction and this will go right into the hole with no welding required.  The threads have been designed to be sanitary so you just screw it against your vessel wall and none of the threads will be exposed to liquid. The soft silicon seals will seal against curved surfaces of your pots and other vessels.

If you want to make a really smooth hole easily in your vessel walls we recommend the use of a step drill bit and 20mm hole punch.

Length: approx. 100mm
From: Kegland

A 1.5" tri-clamp thermowell fitting from Krome Dispense that is approx. 15cm long.

- 304 Stainless Steel
- Approx. 15cm thermowell

Does not include tri-clamp clamp or gasket.

From: Krome Dispense

This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.

Having the thermowell attach to the lid of a fermenter is ideal as it means the penetration through the fermenter body is at the top of the fermenter not below the liquid line. This makes the whole process more sanitary and reduces the number of difficult parts to clean.

This thermowell can be pushed through a bung with a 6-8mm hole but it also includes the Duotight bulkhead fitting that you can use to attach this thermowell to the lid of your FermZilla Fermenter.

It goes right into the middle of the core of your vessel meaning you get an accurate core reading of the liquid in the tank/vessel.

Note: If you need to shorten the length of this thermowell tube then simply use a tube cutter to the desired length.

Made from: 304 stainless steel
Dimensions: 8mm OD x 7mm ID
From: Kegland

Thread seal tape (also known as PTFE tape or plumber's tape) is a polytetrafluoroethylene (PTFE) film tape commonly used in plumbing for sealing pipe threads. 

Thread seal tape lubricates allowing for a deeper seating of the threads, and it helps prevent the threads from seizing when being unscrewed. The tape also works as a deformable filler and thread lubricant, helping to seal the joint without hardening or making it more difficult to tighten, and instead making it easier to tighten.

Typically the tape is wrapped around a pipe's thread three times before it is screwed into place.

Tri-Clamp Cap to Ball Lock Post fitting, with both liquid and gas post options. These 1.5" tri-clamp fittings provide a sanitary and leak-proof connection, and can be used with our ball lock connectors. The price is per single unit - gas or liquid - not for pair like in the photos. 

From: Krome Dispense
Material: Stainless 304

A 304 stainless steel 1.5 inch -2 inch Tri-clover adaptor/reducer.

Standard 2" tri-clamp compatible with Grainfather GF30 Conical Fermenter Dual Valve as well as G40/G70 distilling attachments.

A 1.5 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 1.5 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 1.5 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A specially designed seal to seal the Pure Distilling 1.5 Inch Bubble Plate to the 1.5 Inch Sight Glass.

Note: This is not the same seal as a standard 1.5″ Tri-Clamp seal.