Sort by:
The Create+ Vented Collection Cup is designed for use with 2” tri-clamp compatible distilling systems. The stainless steel Vented Collection Cup integrates into a modular distilling system, facilitating the secure connection of distillate collection tubing while allowing safe venting of pressure during the distillation process.
Key features:
- Connects to 2" tri-clamp distilling accessories
- 304 grade sainless steel construction
- High temperature resistent food grade silicone
INSTRUCTIONS: Insert Collection Cup into your distilling system, ensure the vent weld is at least horizontal so that distillate flows out of the barbed tube, place a silicone gasket in the tri-clamp connection and secure with a tri-clamp.
CLEANING BEFORE USE: Rinse all components with fresh, clean water before the first distillation run.
CLEANING AFTER USE: If needed, thoroughly rinse the section to remove any wash or debris. Use a non-scented brewery cleaner and a soft brush to remove any stubborn debris.
CAUTION: After distillation is complete, the surface will be very hot. Allow to cool before handling.
WHATS INCLUDED
- Vented Collection Cup with Ø10 mm Barbed Tube and Vent Port
- 2" Tri-clamp
- 2" Silicone Gasket
SPECIFICATIONS
- Dimensions: H 11.3 cm x W 7.1 cm x D 5.1 cm
- Vent port/tube Ø12 mm
- Barbed tube Ø10 mm
- Weight: 0.170 kg
NOTE: The Still Spirits Boiler Lid and Alembic Dome are designed primarily for small to medium-sized distilling setups that do not have heavy, off-centre attachments. The lid and dome are reasonably flexible and sturdy enough to fit components that are within the following specifications:
- A total column & condenser height up to 1.1 m (3.6 ft) from the lid or dome.
- A total column & condenser weight up to 11 kg (24 lbs), including up to 2 kg (4.4 lbs) of off-centre weight from a swan neck, lyne arm, or condenser running in parallel with the column and offset up to 160 mm (6”) to the main column.
We recommend external support if:
- Your column & condenser exceeds the above specifications.
- The lyne arm is not vertical but angled or perpendicular running away from the column, resulting in significantly distant off-centre weight.
- If the column & condenser is noticeably leaning.
The Create+ Voltage Controller allows for better control of cuts during a spirit run. Reducing the heat input using the voltage controller will allow for a slower controlled distillation; this makes it easier to distinguish between heads, hearts and tails. Especially useful during pot distillation or vapour infusion spirit runs.
It also allows for the ability to then increase heat input as the distillate output slows towards the end of a run. This is especially useful towards the end of a pot distillation run during the ‘tails’ of a spirit run.
Designed for use with the Create+ Boiler 25 L. Electrical Safety Certified for use in New Zealand and Australia.
Specification
- Power rating: 2400W
- Plug rating: 250V AC, 10A
- Socket rating: 250V AC, 10A
- Max output current rating: 10A
- Product rated supply voltage : 220 - 240V AC
- Rated supply frequency: 50/60 Hz
- Size: 150 x 160 x 90 mm (approx.)
- Weight: 800 g
- Warranty: 12 months
The Create+ Water Flow Regulator is designed for use with reflux distilling systems like the T500, this regulator ensures a steady, controlled water flow for consistent, high-quality results. It features an easy tap connection, built-in water pump, float valve to prevent overflow, and an adjustable flow control handle for precise operation and push fit connections to make connecting the hosing a breeze..
- Compatible with the T500 & similar cooling management reflux systems
- Ergonomic flow controller for easy adjustments
- Stable water flow for high quality distillate
- Built in pump to supply water to your system
- A float valve to regulate water capacity
- Reservoir to store up to 1 L of water
- Reliable push-fit connections
Whats Included
- Create+ Water Flow Regulator with pump
- Flow Control Handle
- Inlet Hose
- Push-fit Connection
- Push-fit to Thread Adapter (for use with Tap Adapters provided with T500)
- Power Cable and Adapter
- Instructions
Specifications
- This Water Flow Regulator can be used with any still that requires less than 1.8 L per min of cooling water
- 3 year warranty
A replacement temperature sensor with a teflon wire and stainless steel probe for the T500 Still. It could also be used for many other applications.
Includes battery.
Temperature range: -20℃ - 200℃
Ideal for adjusting the water flow for stills. An adapter is included so the unit should work on a 22mm and 24mm threaded faucet. This unit is a needle valve design which allows accurate adjustment of the water flow.
We're all familiar with having to try and keep someone from flushing the toilet or turning the dishwasher on while we're distilling so we can get the best results. Now you don't have to worry. The Still Spirits Water Flow Regulator will help you to perfectly control your water flow, speeding up your distillation when using your still.
We have designed your own small water supply especially for your still. Connect this device to your tap, let it fill with water, and you have a reservoir of water for your still.
The Water Flow Regulator includes:
• It's own built in pump to supply water to your still
• A float valve to regulate how much water it holds
• A water flow controller, so that you can set it to the exact flow rate for your needs
• A cool reservoir to store up to 1 L of water.
With this connected to your still, you never have to worry about temperature variation again. High quality and simple to use
Replacement food grade silicone tubing for the top loop of the T500 Reflux Condenser.
Internal Diameter: 6 mm
Length: 0.2 m
Replacement PVC tubing for the T500 Still.
ID: 6mm
Length: 1.1m
Replacement distillate out tube for the T500 Reflux Condenser.
Replacement water discharge tubing for the T500 Still. Connect to outlet block and run to drain.
ID: 8mm
Length: 1.5m
Lead free brass adaptor that screws into the lid of the Pure Distilling Boiler and attaches to a triclover fitting.
Standard 2" tri-clamp compatible with Grainfather GF30 Conical Fermenter Dual Valve as well as G40/G70 distilling attachments.
A 1.5 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 1.5 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 1.5 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A specially designed seal to seal the Pure Distilling 1.5 Inch Bubble Plate to the 1.5 Inch Sight Glass.
Note: This is not the same seal as a standard 1.5″ Tri-Clamp seal.
A 1.5" Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.
A 1.5 inch silicone tri-clover/tri-clamp seal.
A 2 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 2 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 2 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A specially designed seal to seal the Pure Distilling 2 Inch Bubble Plate to the 2 Inch Sight Glass.
Note: This is not the same seal as a standard 2″ Tri-Clamp seal.
A 2" Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.
A 2 inch silicone tri-clover/tri-clamp seal.
A 304 stainless steel 2 inch -4 inch Tri-clover adaptor/reducer.
A 4 inch Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.
A 4 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 4 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A 4 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.
A specially designed seal to seal the Pure Distilling 4 Inch Bubble Plate to the 4 Inch Sight Glass.
Note: This is not the same seal as a standard 4″ Tri-Clamp seal.
A 4 inch silicone tri-clover/tri-clamp seal.
A 1.5 inch triclover sightglass made from 304 stainless steel.
Specifications
- Made from 304 stainless steel
- Viewing lens is High Borosilicate glass
- Operating Temp: -20-+135℃
- Max pressure: 40PSI
- Weight: 1.5kg
- Dimensions: 15cm × 18cm × 11cm
A 304 stainless steel tri clover fitting that will allow you to connect 1.5″ tri clover fittings to different vessels and systems. Includes a locknut & o-ring to secure the fitting.
Bulkhead fits hole approximately 42mm in diameter.
A 2 inch tri clover sight glass made from 304 stainless steel.
Specifications
- Made from 304 stainless steel
- Viewing lens is High Borosilicate glass
- Operating Temp: -20-+135℃
- Max pressure: 40PSI
- Weight: 1.5kg
- Dimensions: 15cm × 18cm × 11cm
