Search results

2" Tri-Clamp Sight Glass - Hop Bong with PCO1881 Male Port and black bottle cap.

Named purely on its looks and not its function. The Hop Bong is a versatile pressurisable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory.

This particular sized tri-clamp hop bong was designed for the FermZilla Tri-Conical and All Rounder fermenters with the new tri-clamp adapted pressure lid. It can also be adapted to any 2" tri-clamp port in your system to use either inline or as a dry hopping device.

Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic.

Depending on how you set up your Hop Bong, the most common two fittings for the PCO Port are the Duotight 6.35mm Red Gas Carbonation Cap or Duotight 6.35mm Yellow Gas Carbonation Cap , and the Red PRV Cap.

Please note that the Hop Bong is not made from glass. It is made from special engineering plastic.

Capacity in Hop Pellets
150g to 180g

From: Kegland

A refractometer is used to test sugar concentrations in a solution. When light passes through a liquid it bends at an angle. Depending on the density of the liquid, this angle becomes more or less pronounced. Refractometers work using this property and translate this shifted angle of refracted light to fall on a graduated Brix chart that is viewable in the eyepiece. 

When brewing a refractometer allows you to take instant gravity measurements during mash, run-off, or during the boil. A valuable tool for all grain and extract brewers alike.

As the density of wort is not the same as a sugar water solution you may wish to calibrate your refractometer when measuring wort. Click here for more information on how to do this.

When making wine a refractometer makes it very easy to measure the sugar levels at the crush or of your must.

Using a Refractometer:

To use, apply 2-3 drops to the prism face, close the cover and wait 30 seconds. Look through the eye-piece - the line on the screen will show the Brix % and Specific Gravity reading.

Calibrate the unit to 0.0 Brix before use with distilled water.

This model comes with ATC (Automatic Temperature Compensation) allowing you to use the refractometer between 10 / 30 degrees Celsius so the temperature of the sample is irrelevant. 

Comes with:
- Carry case
- Pipette
- Calibration Screw Driver

Note: This tool is used to measure unfermented wort. Once alcohol is present in the wort, the use of a correction table is advised.  It is possible to use a calculator to convert the reading, however it may not be as accurate as a hydrometer reading.

This is a low watt density warming wand to be used on a fermenter to maintain warmer yeast profile temperatures in the colder months of the year.

• 125watt
• 1.5" Tri-Clamp

From: Kegland

Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread Bulkhead (suits TempTwister).

Looking for high quaility push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them.  The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings.  This makes these fittings even more reliable and reduces the chance of a leak significantly.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi

Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.

What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.

EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds.   When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.

From: Kegland

• High accuracy 0.1 degree C.
• Dual plugs so you can control heating and cooling devices with the one controller
• 2 x 10amp sockets on rear; one for heating and one for cooling
• Works from -45C up to 120C
• Comes with fully waterproof probe so you can immerse the probe in water
• Uses “50k ohm” Probe
• Manufactured in compliance with Australian Standards

Seal Kit for both the Ball Lock and Pin Lock type Cornelius kegs.

Includes:

• 1 x Low2 Hatch/Keg Lid O-Ring (Yellow)
• 2 x Keg post o-rings
• 2 x Dip tube o-rings

What is Low2?
Low2 O-Rings are the new golden yellow standard of homebrew keg parts from Kegland. Why? Because of their unique composition (Synthetic M-Class and Cross-Linked Elastomers), they have superior oxygen barrier properties than that of the previus O-Rings (Silicone). This results in your beverage staying fresher for longer.

From: Kegland

Garden Hose Female x Grip Hose Connector 12mm / 1/2" Coupling

These easy to use garden hose quick connector couplings are really handy for connecting your hose to a female hose adaptor.

Specifications:

• Brass Construction
• Fits most male garden hose fittings
• 12mm ~ 1/2inch Barb with compression grip fitting
• Includes rubber washer so no teflon tape needed

From: Kegland

The Portable CO2 Mini Regulator Kit is the perfect regulator to use when you don't want to be carting around a large co2 cylinder. Perfect for taking kegs or mini kegs to parties or gatherings, making dispensing a perfectly carbonated beer easy. 

The kit has an inlet for standard threaded disposable 16g CO2 canisters plus adaptors for paintball cylinders, 74g CO2 cartridges and SodaStream cylinders.

Whats Included

• Regulator with aluminium body
• 3 x Inlet adapters for different connections
• Outlet fitting

A 304 stainless steel 2 inch -4 inch Tri-clover adaptor/reducer.

This easy to use SodaStream Cylinder Filling Adaptor will enable you to fill your own CO2 from your larger bulk cylinder into smaller SodaStream cylinders. An easy and inexpensive way to fill your own Sodastream Cylinders at home at a fraction of the cost of getting the refills from your local store.

Note: Does not fit or work with the latest Sodastream cylinders, only older cylinders. The CO2 Cylinder and Sodastream cylinder in the photos is not included.

When using, be sure to following these important points:

1. That the seals goes in the correct location. So when the SodaStream Filling Adaptor arrives, please make sure to use the correct seal in the correct side.

2. Make sure to put the Sodastream cylinder on the correct side. The SodaStream cylinder thread can actually fit both sides of this adaptor, but the CO2 cylinder only fit's into the ROUND SIDE. As a result you MUST put the Sodastream cylinder into the HEXAGONAL SIDE. (as shown in image)

Hoses play a huge role in draft beer dispensing. They carry gas from the tank to the coupler and beer from the keg right up to the faucet. These pipes are of soft, flexible but durable material. They are usually of Vinyl and Polypropylene. The hoses are also part of glycol pythons.

Hoses are connected through adapters and barbs to form the entire dispensing system. The length really depends on how far your serving point is from the keg. You might have to shorten or cut out from a large bundle. For any of this, you require a Hose and Tubing Cutter.

This cutter is sturdy and sharp that cuts right through the hose in a jiffy without leaving any rough edges too.

• Material: Plastic
• Finish: Raw
• Color: Black

Looking for a smaller option, you'll find one here.

From: Krome Dispense

NukaTap Flow Control Auto Close Spring.

The NukaTap Flow Control is the world's only forward sealing flow control tap that can use a auto close spring. By inserting the spring between the flow control device and NukaTap shuttle the tap will automatically close when you let go of the handle. This is perfect for customers who may not be diligent enough to remember to completely turn off the tap after each pour. Or for those with little kids or pesky cats that knock everything around!

This very inexpensive spring can save you from emptying an entire keg and then loosing a whole bottle of gas.

Note: The spring is not compatible with the NukaTap Standard Models, the auto close spring for those can be purchased here.

From: Kegland

Duotight 8mm OD retaining circlip, suits any Duotight 8mm fitting. When clipped into place, this circlip prevents the collar of the Duotight fitting from being pushed inwards, making it impossible for the fitting to release its grip on any hose!

Note: Duotight fittings, ball lock disconnects and hose sold seperately.

From: Kegland

A sealed pressure gauge is the most sanitary and safest solution for measuring pressure. Designed to prevent krausen from plugging the gauge, it ensures longer-lasting performance and unparalleled reliability.

This 1.5" tri-clamp pressure gauge can be used with any stainless steel fermenter with 1.5" tri-clamp ports. Liquid filled gauges offer better performance and longer lifespan compared to dry gauges.

The dial face reads in both psi and BAR.

From: Kegland