Handcraft Supplies 5L Fermenter is perfect for brewing up to 4.5 litre batches of wine, beer, cider, or other fermentation.

Stackable and made from food-grade plastic with litre markings on the side so you can easily see how much to top up to. Comes with a sturdy plastic handle for easy transportation.

Note: Does not include lid.

Handcraft Supplies 5L Fermenter with Lid & Grommet is perfect for brewing up to 4.5 litre batches of wine, beer, cider, or other fermentation. 

Comes with a lid pre-fit with a grommet, ready for an airlock. Stackable and made from food-grade plastic with litre markings on the side so you can easily see how much to top up to. Comes with a sturdy plastic handle for easy transportation. 

A 60 litre plastic carboy/barrel fermenter suitable for fermenting beer, cider, wine, or spirits.

You may also require:

• Standard Tap (Threaded)
• Tap for Handcraft Supplies Fermenters (includes seal)
• Airlock Grommet
• Airlock - Standard S Shape or Senior Airlock

Master Your Brew, Wine, or Spirit Wash with Precision Heat Control.

Temperature dictates fermentation success. Too cold, and you risk sluggish, stuck ferments. Too warm, and you invite excess esters, fusel alcohols, and VDKs—compounds that compromise a clean flavour profile. This applies equally to beer, wine, and distilled spirits.

The Handcraft Supplies Adjustable Heat Belt solves both extremes. It provides gentle, consistent warmth to your fermenter, but with a unique mechanical twist: Lower the belt to increase heat; raise it to decrease heat. This lets you actively manage the exothermic peak of fermentation, preventing overheating while ensuring your yeast finishes strong.

• Universal Fit: Carboys, buckets, and stainless steel units.

• Strain-Specific Control: Easily maintain the right temperature for the yeast you are using (e.g.: 18–22°C for ales, 8–15°C for lagers, 15–20°C for white wines, 20–25°C for red wines, and 25–30°C for rum or whisky washes.

• Simple & Safe: Low-wattage, secure tightening design.

While this heat belt is ideal for beer, it is equally valuable for wine and spirits production. Wine ferments thrive on stable temperatures to preserve delicate fruit esters and prevent volatile acidity, while spirit washes—particularly for rum and whiskey—often require warmer conditions to maximise yeast attenuation and develop desired flavour precursors. For ultimate precision across any ferment, pair your heat belt with a temperature controller such as a Rapt Temperature Controller or MKII Temperature Controller. This automates the heating cycle, holding your wash, must, or ber within a fraction of a degree of your target. For the most accurate reading, tape the probe directly to your vessel (insulated from ambient air) or use a thermowell to monitor the true core temperature—ensuring professional-grade consistency whether you are brewing beer, fermenting wine, or making spirits.

Brew smarter, not harder. Get your Handcraft Supplies heat belt today.

The Handcraft Supplies Fermentation Equipment Kit contains the essential equipment you require for your fermentation needs. Whether you're making beer, cider, wine, or a wash for distilling, this kit enables you to get your fermentation underway and completed successfully. All you need are your ingredients and a suitable cleaner and sanitiser.

Designed for 23 litre batches. Simply assemble, sanitise and add your ingredients.

This kit is made up of:

30L Fermenter + Lid 
Stick-on Thermometer Strip
Bubbler Airlock
Grommet
Tap
Plastic Spoon
Hydrometer

Handcraft Supplies fermenter set containing a 30L bucket with lid and accessories, ready to ferment. Includes litre markers down the side. Use for primary or secondary fermenter, or even as a bottling bucket.

This kit is made up of:

Stick-on Thermometer Strip
Bubbler Airlock
Top Hat Grommet
Sediment Reducer
Tap
30L Fermenter + Lid

This handy spring clamp has been the tool of choice for many KegLand employees to hold the malt pipe silicone hose in place during the mash.

Handy Clamp (4" Long) - ideal for use with a Brewzilla.

This clamp features a heavy-duty muslin spring which ensures your silicone hose never accidentally pops out of your mash tun and spills your precious nectar over your brewery floor.

It features rounded handles for a comfortable grip and a PE end grip to ensure your hosing is kept secure.

This clamp is made from PP and PE which have good chemical resistance so it will stand up to the task for use around common brewing cleaners and sanitisers such as StellarClean/PBW and StellarSan.

These spring clamps have a multitude of potential uses throughout your brewing outside of securing silicone hosing.

From: Kegland

A brewing heater belt that fits around your fermenter to provide steady and constant warmth for your brew. The 30 watts will gently warm without creating a hot spot, and can be moved up or down the fermenter to increase or decrease the heat transfer to the brew.

To further control the temperature of your fermentation, combine with a RAPT Temperature Controller or similar to regulate the heater belt automatically.

Note: fermenter not included.

From: Kegland

These 304 Stainless 2200w weldless elements are designed to fit a 32mm hole inside the wall of your brewing vessel or boiler. It comes bundled with the power cord.

We do recommend using a RAPT Temperature Controller to run this element with the appropriate thermowell or temperature probe attachment.

These electric brewing elements are highly recommended for your HLT, or even for a HERMS or RIMS setup. Multiple elements may be required for larger volumes and depending on what temperature you are trying to achieve. If you are going to be using these elements directly in your mash tun, and will try to maintain temperature using the element, we would recommend getting a power control chip 3600w to modify the power output to the element. Too higher power directly in contact with your malted grain can cause scorching/off flavours as the temperature may not be evenly distributed and isolated purely around the element itself.

Element Length: approx. 300mm
Diameter: approx. 25mm
Thread: approx. 32mm
From: Kegland

3600 Watt Stainless Steel Heating Element with 2 inch tri-clamp (220-240v)

It can be fitted to a 2" tri-clamp ferrule. It does have a water-resistant screw element guard. This was produced to be used with the 118L Kegmenter that has 2" ferrules.

It is highly regarded as a popular and reliable element for distillers and homebrewers.

This element is to be installed by a professional electrician with a 15amp Cord. 

From: Kegland

Fermentation Heating Wrap Belt - With Velcro Strap (30watts) 220-240VAC (50-60hz)

Perfect heating solution for those who want more even coverage and absolute certainty that their PET fermenter will not melt even if the fermenter is empty.

Punching in at an ample 30 watts, this heating wrap belt is great when paired with insulation and a temperature controller box to dial in that optimum fermentation profile.

To further control the temperature of your fermentation, combine with a RAPT Temperature Controller or similar to regulate the Heating Wrap Belt automatically.

Features:

• Easy to use
• Handy velcro strap
• Low watt density
• Durable vinyl coating
• 30 watt gentle heating
• Great for fermenters or bottle conditioning
• Sit on top or wrap around your fermentation vessel

Dimensions: approx. 1000mm x 250mm

From: Kegland

Heavy Duty Vulcanized Latex Brewing Gloves - 55cm Long.

These heavy duty brewing gloves are made from vulcanized latex, ideal for cleaning around the brewery or even the home. Seriously long for getting those arms deep into Kegmenters, Fermzillas and those brew pots.

Tough chemical resistant material provides good protection to your hands during clean-up and sanitary handling of equipment. They are 55cm long so will also protect the forearm when reaching into harsh cleaning chemicals.

Weight: approx. 300gm
From: Kegland

The Heat Resistant Gloves / HIZO Oven Mitts are as impressive as they are functional with the ability to handle contact with temperatures of up to 500° Celsius (932°F). This means that it is perfect for use with oven baking, hot pots, grilling, barbecuing, and woodstoves.

Fashioned with high-quality aramid fibers which work to insulate and protect hands from burning temperatures, these gloves have a comfortable cotton and polyester lining which allows for breathability to resist sweating and a gauntlet-length style of design to protect wrists and forearm from scorching heat as well. These gloves are thick to provide excellent thermal protection and durability, but they are lightweight for extended use without fatigue.

Sizing: Medium only

With heat resistance up to 500°C, these gloves are perfect for:

• Perfect for oven baking, hot pots, grilling, barbecuing, and woodstoves
• Adjusting logs in the fireplace
• Touching scorching hot utensils or food while boiling or frying
• Changing light bulbs

Features:

• High-quality aramid fibers for insulation and cotton and polyester lining
• Designed for mobility and flexibility in mind
• Food-grade silicone layer
• Machine-washable, and can be easily hung on the line to dry

From: Kegland

30mm Hoffman Clamp - Stainless Steel.

Hoffman Clamps are used to control the flow in flexible tubing. The clamps have a machined adjustment screw to permit accurate regulation of the flow.

Screw Compressor Clamps are used to control the flow in flexible tubing. The clamps have a machined adjustment screw to permit accurate regulation of the flow. All corners are rounded to prevent cutting of the tubing.

This can be particularly useful when using a liquid management still.

Size: 30mm
From: Kegland

2" Tri-Clamp Sight Glass - Hop Bong with PCO1881 Male Port and black bottle cap.

Named purely on its looks and not its function. The Hop Bong is a versatile pressurisable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory.

This particular sized tri-clamp hop bong was designed for the FermZilla Tri-Conical and All Rounder fermenters with the new tri-clamp adapted pressure lid. It can also be adapted to any 2" tri-clamp port in your system to use either inline or as a dry hopping device.

Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic.

Depending on how you set up your Hop Bong, the most common two fittings for the PCO Port are the Duotight 6.35mm Red Gas Carbonation Cap or Duotight 6.35mm Yellow Gas Carbonation Cap , and the Red PRV Cap.

Please note that the Hop Bong is not made from glass. It is made from special engineering plastic.

Capacity in Hop Pellets
150g to 180g

From: Kegland

This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla.

It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel. 

Diameter: approx. 66mm Heigh: approx. 300 mm.

From: Kegland

This polyester bag is perfect for small grain additions or for hopping beer. It is a tube of fabric that is approximately 15cm wide and 75cm long. Both ends are open for easy cleaning and can simply be tied closed while being used. Perfect for grain or hops (suitable for use up to 110 degrees C).

Hoses play a huge role in draft beer dispensing. They carry gas from the tank to the coupler and beer from the keg right up to the faucet. These pipes are of soft, flexible but durable material. They are usually of Vinyl and Polypropylene. The hoses are also part of glycol pythons.

Hoses are connected through adapters and barbs to form the entire dispensing system. The length really depends on how far your serving point is from the keg. You might have to shorten or cut out from a large bundle. For any of this, you require a Hose and Tubing Cutter.

This cutter is sturdy and sharp that cuts right through the hose in a jiffy without leaving any rough edges too.

• Material: Plastic
• Finish: Raw
• Color: Black

Looking for a smaller option, you'll find one here.

From: Krome Dispense

A tool for cutting hose and tube, with a stainless steel blade.

From: Krome Dispense

A hydrometer is an essential tool for testing starting and finishing gravity, or sugar content, in beer or wine or spirit fermentations. This is a triple scale hydrometer - specific gravity, potential alcohol and approx. sugar per litre.

Best used with a trial jar (sold separately).

Handcraft Supplies Triple Scale Fermentation Hydrometer measures the specific gravity, potential alcohol, and approx. sugar content of any fermentable liquid, whether you're making wine, cider, beer, or distilling wash. 

Best used with a trial jar (sold separately).

Infrared Thermometer Gun -50C to +580C (Black)

This thermometer gun has a built-in Dual laser that can be switched On and Off. Dual laser is an important feature when choosing infrared thermometers because it allows for much higher accuracy of readings. When measuring an object a Dual Laser will help greatly in finding the convergence point of the measured target and the spot ratio, which can only be achieved with Dual Laser.

Features:

• Double Laser pointer for accurate target aiming
• Simple one-handed operation
• Laser ON/OFF Switch
• Low battery indication
• LED backlight system for operation under poor illumination
• C° / °F temperature unit conversion
• Automatic Power off in 15 seconds without any operation
• Display hold, scan function

Note:
1. When using this product to measure temperature, consider the ratio between the distance (the length from the product to the measured object) and the size of the measurement area, referred to as the object distance ratio. When the distance between the product and the measured object increases, the measurement area will increase accordingly.

2. If you want to use boiled water to measure the quality of the product, please note that when measuring boiling liquids, do not allow smoke or water vapour to contact the temperature sensing area, and keep the measurement angle at 45 ~ 60 degrees.

Specifications:

• Temperature Range: -50 to 550°C
• Accuracy: ± 2% or 2°C
• Distance Spot Ratio: 12:1
• Emissivity: 0.1~1.0(Adjustable)
• Response Time Wavelength: 500ms & (8-14) um
• Repeatability: ± 1% or 1°C
• Resolution: 1°C or 1°F
• Storage Temperature: -20-50°C
• Operating Temperature: 0-50°C

From: Kegland

This unit has been designed to fit Kegland standard Single, Double and Triple Tap Kegland Kegerator Towers or any other 76mm diameter font. 

Keep your beer icy-cold with this insulated tower/font cover right out of the first drop. Most kegerators that we sell include a font fan that blows cold fridge air up the font. With that said heat loss from the stainless font surface causes the font temperature to rise meaning that a small amount of beer contributes to the "first pour foam effect".

These extra thick covers are made from 7mm neoprene, meaning your beer will stay cold even if the hot sun is beating down directly on the font.

This helps save power as your fridge will not be working as hard, and you pay less in power. So this thing practically pays for itself!

How to Install

1. Remove taps from the font. (no need to remove the shank from the font, just the taps).

2. Pull the insulated cooler down over the font.

3. Mark the tap holes and use a sharp pair of scissors to cut a hole in the neoprene jacket.

4. Re-attach the taps.

NOTE: Nail cutting scissors are particularly good for this application, or a 5/8" Hole Punch.

Please note these only come with a Kegland logo. They are not sold in plain black.

From: Kegland

Now updated with the all new duotight 8mm Ball Lock Disconnect (Grey+Red/Gas)

This kit has been designed for simplicity and ease of putting together. 

This Kit Contains:
1 x BlowTie Spunding Valve Gen 2 with 0-15psi Integrated Gauge
1 x Duotight 8mm (5/16") x Ball Lock Disconnect (Grey+ Red/Gas)
1 x Rigid 8mm Plastic Joiner

All new compact BlowTie Spunding Valve Gen2 Integrated Kit. If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job. 

If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job.

The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure.

This BlowTie unit can be easily disassembled for cleaning using a Phillips head screw driver.

Designed to suit 8mm OD (5/16") Evabarrier Tubing. 

Specifications:
1. Suits pressures 0-15psi (but with different gauges the unit can go above 100psi)
2. Made from food-grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides

If you are looking for a compact digital gauge with backlight illumination click here. This should only be used on a blowtie if you have excess tubing to stop liquid reaching the gauge. If liquid enters the digital gauge it will break.

A spring loaded bottling valve and adapter that connects to the Italian Barrel Tap With Locknut.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The Equal Tee 8mm can be used split gas lines or other tubing.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The FFL 1/4 Inch to 5/16 Inch (8mm) Push-fit connects to 1/4 inch MFL fittings such as the Beer MFL Ball Lock Disconnect and Gas MFL Ball Lock Disconnect and is suitable for use with 5/16 inch/8mm tubing.

Hand tighten only. Over tightening could damage the fitting.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

These valves have been designed to allow temporary servicing of downstream equipment and must only be used in the fully open or fully closed position.

DO NOT USE THESE VALVES: In a partially open position to control flow; to provide a permanent termination; without tubing assembled or plugged (or threaded connections sealed, or as a tap or “faucet”.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The Two Way Divider quickly and easily splits a line into two separate lines.

Hand tighten only. Over tightening could damage the fitting.

When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on Pump or Glycol systems.

Compatible with:

JoinTech Male Connector with Auto Shut Off x 1/2 Inch BSPT
JoinTech Male Connector with Auto Shut Off x 13mm Barb

Features:

• JoinTech Black UV Stable Design
• Equipped with Auto Shut Off Valve
• Vacuum Rating of 60psi
• Connections:
  Female Plug Quick Disconnect
  1/2" BSP Male Thread
• Medical Grade Materials:
  Body: High-Strength, Chemically Resistant Polyketone Plastic
  Spring: 316 Stainless Steel
  O-Ring: EPDM
• Operating Pressure: Vacuum to 60 PSI
• Temperature Tolerance: -40°C to 138°C
• 3/8" Flow Path

From: Kegland

When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on the hosing used to attach to Pumps or Glycol systems.

Compatible with:

JoinTech Male Connector with Auto Shut Off x 1/2 Inch BSPT
JoinTech Male Connector with Auto Shut Off x 13mm Barb

Features:

• JoinTech Black UV Stable Design
• Equipped with Auto Shut Off Valve
• Vacuum Rating of 60 PSI
• Connections:
  Female Plug Quick Disconnect
  13mm Barb
• Medical Grade Materials:
  Body: High-Strength, Chemically Resistant Polyketone Plastic
  Spring: 316 Stainless Steel
  O-Ring: EPDM
• Operating Pressure: Vacuum to 60 PSI
• Temperature Tolerance: -40°C to 138°C
• 3/8" Flow Path

From: Kegland

When not connected to another JoinTech Connector this will not allow any flow. Incredibly useful on Pump or Glycol systems.

Compatible with:

JoinTech Female Connector with Auto Shut Off x 13mm Barb
JoinTech Female Connector with Auto Shut Off x 1/2 Inch BSPT Male

Features:

• JoinTech Black UV Stable Design
• Equipped with Auto Shut Off Valve
• Vacuum Rating of 60psi
• Connections:
  Male Plug Quick Disconnect
  1/2" BSP
• Medical Grade Materials:
  Body: High-Strength, Chemically Resistant Polyketone Plastic
  Spring: 316 Stainless Steel
  O-Ring: EPDM
• Operating Pressure: Vacuum to 60 PSI
• Temperature Tolerance: -40°C to 138°C
• 3/8" Flow Path

From: Kegland