Beer Brewing

Thermometer With Clip - a multi-purpose thermometer you can use when brewing beer, heating milk for cheese making, or frothing milk for coffee.

This Thermometer With Clip has a long stem and a clip that you can use to attach the thermometer to the side of your equipment. 

The thermometer is made of stainless steel that is durable and corrosion-resistant. The dial is large which makes it easy to note the reading.

Probe length: 125mm

Temperature range: 0℃ - 110℃

From: Krome Dispense

A stainless steel, 1/2" thread, weldless thermowell (takes any probe up to 7mm ID).

This thermowell works great with any kegmenter, keggle, brew pot, boiler and various other brewery hardware to get an accurate core temperature of your vessles.

This thermowell has a 7mm bore, so it's ideally suited to any probe type up to 7mm.  Most probes are 6.5mm or smaller in diameter meaning they will fit nicely into this well.  It's ideal for the RAPT Temperature controllers.

This is a weld free design so all you need to do is drill a 20mm hole and file this out a fraction and this will go right into the hole with no welding required.  The threads have been designed to be sanitary so you just screw it against your vessel wall and none of the threads will be exposed to liquid. The soft silicon seals will seal against curved surfaces of your pots and other vessels.

If you want to make a really smooth hole easily in your vessel walls we recommend the use of a step drill bit and 20mm hole punch.

Length: approx. 100mm
From: Kegland

A 1.5" tri-clamp thermowell fitting from Krome Dispense that is approx. 15cm long.

- 304 Stainless Steel
- Approx. 15cm thermowell

Does not include tri-clamp clamp or gasket.

From: Krome Dispense

This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.

Having the thermowell attach to the lid of a fermenter is ideal as it means the penetration through the fermenter body is at the top of the fermenter not below the liquid line. This makes the whole process more sanitary and reduces the number of difficult parts to clean.

This thermowell can be pushed through a bung with a 6-8mm hole but it also includes the Duotight bulkhead fitting that you can use to attach this thermowell to the lid of your FermZilla Fermenter.

It goes right into the middle of the core of your vessel meaning you get an accurate core reading of the liquid in the tank/vessel.

Note: If you need to shorten the length of this thermowell tube then simply use a tube cutter to the desired length.

Made from: 304 stainless steel
Dimensions: 8mm OD x 7mm ID
From: Kegland

Thread seal tape (also known as PTFE tape or plumber's tape) is a polytetrafluoroethylene (PTFE) film tape commonly used in plumbing for sealing pipe threads. 

Thread seal tape lubricates allowing for a deeper seating of the threads, and it helps prevent the threads from seizing when being unscrewed. The tape also works as a deformable filler and thread lubricant, helping to seal the joint without hardening or making it more difficult to tighten, and instead making it easier to tighten.

Typically the tape is wrapped around a pipe's thread three times before it is screwed into place.

Tri-Clamp Cap to Ball Lock Post fitting, with both liquid and gas post options. These 1.5" tri-clamp fittings provide a sanitary and leak-proof connection, and can be used with our ball lock connectors. The price is per single unit - gas or liquid - not for pair like in the photos. 

From: Krome Dispense
Material: Stainless 304

A 304 stainless steel 1.5 inch -2 inch Tri-clover adaptor/reducer.

A 316 stainless steel 2 inch Tri Clover 90° bend.

• Short Radius (1.5x Diameter)
• 320 Grit Finish
• Pre-Welded with Tri Clover Ferrules
• 316 Stainless Steel

Standard 2" tri-clamp compatible with Grainfather GF30 Conical Fermenter Dual Valve as well as G40/G70 distilling attachments.

A 1.5 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 1.5 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 1.5 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A specially designed seal to seal the Pure Distilling 1.5 Inch Bubble Plate to the 1.5 Inch Sight Glass.

Note: This is not the same seal as a standard 1.5″ Tri-Clamp seal.

A 1.5" Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.

A 1.5 inch silicone tri-clover/tri-clamp seal.

A 2 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 2 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 2 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A specially designed seal to seal the Pure Distilling 2 Inch Bubble Plate to the 2 Inch Sight Glass.

Note: This is not the same seal as a standard 2″ Tri-Clamp seal.

A 2" Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.

A 2 inch silicone tri-clover/tri-clamp seal.

A 304 stainless steel 2 inch -4 inch Tri-clover adaptor/reducer.

A 4 inch Tri-Clover/Tri-Clamp clamp made from 304 stainless steel.

A 4 inch silicone tri-clover/tri-clamp seal with a 40 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 4 inch silicone tri-clover/tri-clamp seal with a 60 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A 4 inch silicone tri-clover/tri-clamp seal with a 80 Mesh screen (made from 304 stainless steel) attached to a PTFE edge.

A specially designed seal to seal the Pure Distilling 4 Inch Bubble Plate to the 4 Inch Sight Glass.

Note: This is not the same seal as a standard 4″ Tri-Clamp seal.

A 4 inch silicone tri-clover/tri-clamp seal.