Duotight 8mm (5/16) one way check valve/non-return valve.

This very handy fitting could save your regulator and is a good investment. This particular type of check valve has low opening pressure of only 1 psi. It is suitable for clean liquids such as water or for gas. The spring and internal components are made with stainless steel and quality EPDM seals.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. 

Fits 8mm outer diameter tube. 

Note: colour may vary.

From: Kegland

This Duotight Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.

Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.

Fits 8mm outer diameter tube.

From: Kegland

This Duotight Push-Fit Tee - 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.

Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.

Fits 8mm outer diameter tube.

Note: colour may vary.

From: Kegland

Duotight - 8mm x 1/4 inch BSP Male.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.

These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

From: Kegland

This manifold splits one line into two, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This manifold splits one line into four, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This manifold splits one line into six, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This rigid 50mm long joiner is made from strong polypropylene. It's useful to make rigid joins with push in fittings that are dead straight. Although it's possible to make joins using short pieces of 8mm OD Evabarrier 5mm Beer Line this is far more flexible and when mounting parts to a gas board or wall its will often make things much neater if you use these instead.

The 50mm length is long enough so even after pushing right into two duotight 8mm fittings on both ends you should still have a exposed length of about 3mm so you can still relatively easily take the fittings apart later.

From: Kegland
Dimensions: 8mm OD x 6mm ID x 50mm long

This really handy device is great for filling kegs, keg to keg transfers or fermenter to keg transfers.

Fantastic for use with Fermentasaurus or other pressurisable fermenters.

Simply attach this device to the output gas post of your Keg then when the keg is full it will prevent further liquid exiting the gas post. This means you can literally set and forget and fill kegs automatically without the risk of kegs overflowing all over the floor.

For even better results we recommend this product to be used with the Duotight - BlowTie Diaphram Spunding Valve - Adjustable PRV.  This blowtie spunding valve will also enable to to apply head pressure to the keg meaning you can control the flow speed but also reduce the foam generated in the filling process particularly for carbonated beverages like beer.

This flow stopper includes:

• 2 x duotight 8mm x 5/8 push in fittings
• 1 x ball float
• 1 x stainless spring
• 2 x straight 8mm joiners
• 1 x acrylic sight glass (with 5/8 male thread on either side)

Made exclusively for the Duotight manifolds and Gen 3.0 Duotight 8mm fittings to be mounted to a flat surface.

These can swivel around if you need to mount on a particular angle once stuck down.
They can also easily be removed from the 8mm Duotight side as they simply click/clamp in to each other.

If you are to mount this inside your Kegerator / Keezer, you must do so when the unit is off / warm. It will not stick as well in a moist / cold environment. Best to give it at least 24 hours of stick time before attaching weight / hosing to it.

Wipe down surface with isopropyl alcohol prior to sticking.

Most commonly to be used with:

• 8mm (5/16) duotight x 6 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 4 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 2 Way Manifold with Check Valves & Isolation Valves
• and duotight - 8mm (5/16) x 5 Way Multi-Tee

If you want to know if your Duotight fitting will fit this, it must be a grey Duotight that has a black collet piece.

Not suitable for 8mm ball lock disconnects
Not suitable for multiple re-applications

From: Kegland

The Easy-Siphon makes syphoning your beer or wine simple and is designed to start the flow in one stroke. The Easy-Siphon is made out of acrylic and includes a 60cm racking tube bent to perfection. It also includes an Anti-Sediment Tip.

The Tubing - 9.5mm ID fits snugly over the racking tube.

Compatible with the 5L Glass Jar Demijohn and 5L Glass Jar Demijohn with Screw Cap/Lid.

The Easy Siphon Clip holds your Easy Siphons to Carboys, Buckets and more! Made from lasting plastic materials, so you can clip and unclip your Easy Siphons without issues.

Works with:

• Easy Siphon 3/8"
  
• Easy Syphon Mini - 350mm
  
• Legacy Easy Siphon 3/8"

Please note: if the clip is used with the Legacy Easy Siphons (pre-2022 models), it will not work with the new models afterwards as the clamps will stretch to adapt to the bigger diameter of the older models.

A smaller (shorter) 350ml syphon. Perfect to use with smaller fermenters.

The Tubing - 9.5mm ID fits snugly over the racking tube.

Compatible with the 5L Glass Jar Demijohn and 5L Glass Jar Demijohn with Screw Cap/Lid.

The Emily Metal Wing Bottle Capper is a long lasting, smooth operating, reliable capper made from self-lubricating nylon and is surprisingly strong. 

The unique patented design has a gear driven head that makes capping a breeze since less overall force is required. This model is popular with home brewers for several reasons.

Features and Benefits

• Riveted pivots for heavy usage.

• Caps American sparkling wine bottles by removing and reversing the metal jaws.

• For 26.5 mm bottle caps

• Lighter than metal cappers

• Wider handles – making it easier to operate.

• A built in spring allows the capping mechanism to automatically retract when capping is completed.

• Easy to use. - The built-in magnet allows the cap to be positioned in the capping head and then applied to the bottle rather applying the cap on top of the bottle first.

• Made by Ferrari in Italy.

EVABarrier Black Lightshield 4mm ID x 8mm OD - 12m Roll.

This hose is suitable for a wide range of 8mm push in fittings, either for hydroponic/gardening use or outdoor keg dispensing where UV can damage the product.

Algae will always thrive if sunlight and an exposed nutrient solution is available. That is why it is crucial to use the correct hosing when it comes to hydroponic systems and or outdoor beer dispensing systems.

Prevention is the best cause of action when it comes to algae control. EVABarrier LightShield Black should be your number one choice of hosing when setting up your indoor or outdoor growing space.
UV stable hosing that will not kink or burst under normal use.

Specifications:
4mm Internal Diameter
8mm Outer Diameter
12m Roll

EVABarrier Hosing
Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings.  The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.

Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier and now with LightShield technology an excellent UV and Visible light blocking properties. The significantly better barrier properties means your beverage is better protected from oxygen and also has a better barrier to CO2 loss.  So your beer will stay fresher for longer and not lose carbonation like other beer line types.  In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period.  EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.

Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable.  This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.

From: Kegland

EVABarrier Red Lightshield 5mm ID x 8mm OD - 12m Roll

Red semi-transparent EVABarrier for kegging setups. Easily see your gas lines in minimal light without confusion.

This high quality beer line will keep your previous beverage in it's best possible condition in the process.

This 5mm size is the one of the most common sizes for kegerator setups.

When using this 5mm ID size you will need to use about 3-4 meters of beer line to get adequate flow resistance between your keg and tap for most kegerator setups.

Pressure Rating (with 1.5x safety factor)
30C - 1.4 MPa (200psi)
50C - 0.7MPa (100psi)

This new Red EVA Double walled tubing is made with an EVA outer wall and also an inner proprietary polymer barrier.

Red Outer Barrier
The outer barrier has accurately extruded tolerances and made from an EVA material. It also seals well when used with various John Guest, Duotight or other push in fittings.  The outer barrier gives the tubing excellent kink resistance so the line is able to bend around a tight radius without kinking.

Inner Barrier
The inner barrier is made from a proprietary polymer that has excellent gas barrier.  The significantly better barrier properties means your beer is better protected from oxygen and also has a better barrier to CO2 loss.  So your beer will stay fresher for longer and not loose carbonation like other beer line types.  In some beer line types you may notice that the beer sitting in the lines starts to taste flat and/or oxidised when sitting in the lines for an extended period.  EVABarrier tubing is significantly better in this regard and you will notice a significantly improved freshness of your beer especially if it's been sitting in the lines.

Due to the high density and smooth nature of the EVABarrier inner barrier the tubing internal surface is super smooth and almost completely impermeable.  This makes it difficult for bacteria and other microbes to attach to the inside surface of the tubing.

From: Kegland

This black HDPE lid has been designed to be chemically resistant but also strong enough to hold up to 2.5bar pressure.

This lid can screw onto the top of your Fermzilla Collection Container and this allows you to use the Fermzilla collection container for other stainless fermenters with a 2 inch tri-clamp dump valve.

Note: clamp, seal, and container not included.

From: Kegland

FermZilla 27L Tri-Conical Starter Kit - Generation 3.2

Introducing the Gen3 FermZilla Tri-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and a 600mL collection container with a 3 Inch Tri-clover connection, the gold standard for sanitary design and effortless removal. No more complicated dump valve designs here, just simplicity. Brew with confidence on the new Tri-Clover FermZilla Range.

The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget. With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.

This is an incredible product at an extremely attractive price point in all the different sizes and models.

The FermZilla 27L Tri-Conical can be used in the following ways:

• Basic Gravity Fermenter - New Brewers
• Pressure Brewing Kit - Most Popular
• Hop Bong Pressure Kit - For Intermediate Brewers
• Glycol Twister Pressure Brewing Kit - Glycol Obsessed

What's new the difference between Gen2 and Gen3?
1. Moulded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch tri-clamp butterfly valve
3. 3 Inch tri-clamp 600mL collection container

Is it easier to clean / take apart than the Gen2?
YES, It is by far the easiest Conical PET fermenter to disassemble and clean into all the nooks and crannies. Simply release all pressure inside the vessel and detatch the tri clover clamps.

What does the starter kit come with?
      1 x 27L Conical FermZilla Tri-Conical Base Kit (unassembled)
      1 x 27L Gen3 Tri-Conical Tank with metal neck ring
      1 x Standard Top Lid, with Red PRV (35psi) [2 x Male PCO1881 Cap Threads] [Up to 4 drill ports for accessories]
      1 x Collar Lid Ring
      1 x Grommet PCO1881 Black Cap + 1 x Blank PCO1881 Black Cap for lid
      1 x Premium 3 Piece Airlock
      1 x 3 inch tri-clamp to 3 inch tri-clamp butterfly valve
      1 x 600mL Collection Container & Lid* [2 x Male Cap Threads]
      2 x Blank PCO1881 Black Cap
      1 x 3 piece ~ 3 inch tri clover clamp [+ 1 x 3" Beaded Silicone Seal]
      1 x 2 piece ~ 2 inch tri clover clamp [+ 1 x 2" Beaded Silicone Seal]
      1 x Stainless Stand with swing handles
      1 x Stainless Steel Handle Assembly
      1 x Strip Stick On Thermometer
      1 x Level indicator sticker (Litres and Gallons)
      1 x Spare Lid O-Ring
      1 x Spare Collection Container O-Ring

Instructions:
To download the instruction sheet for this product click on the link below:
FermZilla 27L - Tri-Conical PDF Instruction Manual

Dimensions:

To download the dimensioned drawings for this product click on the link below:
FermZilla 27L Tri-Conical Dimensioned Drawing

Warnings:
Please read the instructions thoroughly before use.

• We will not be held liable for misuse or mishandling of the unit contrary to the instructions.
• Keeping the units out of direct sunlight is a must for all PET fermenters. Sunlight degrades PET.
• Do not expose to temperatures exceeding 35°C and pressure ferment past 5psi at these temperatures.

Please note:
When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage. 

Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.

Help Stabilize Your Fermentation Temperatures with the FermZilla Insulating Jacket
Fits both FermZilla 27L Conical and All Rounder 60L

Give your fermenter practical temperature support! Kegland’s insulating jacket easily zips over your 27L Conical or 60L All Rounder, creating a protective thermal layer to reduce ambient temperature swings. Use it standalone or supercharge your control with these active solutions:

How It Works:

Reduces Temperature Fluctuations: Minimises impact from room temperature changes
Active Heating: Pair with a RAPT Temperature Controller + Heating Wrap
Active Cooling: Use with Temp Twister Coil + Pump Kit
Passive Cooling: Place frozen water bottles between jacket and fermenter
Full Coverage Design: Light-blocking insulation with lid access

Compatibility:
→ FermZilla 27L Conical (Gen 3)
→ All Rounder 60L

Your Complete Thermal System:
Maximize control with these setups:
→ Basic: Jacket alone (reduces fluctuations)
→ Pro Heating: Jacket + RAPT Controller + Heating Wrap
→ Pro Cooling: Jacket + Temp Twister Coil + Pump Kit
→ DIY Cooling: Jacket + frozen bottles

Complete Your Temperature Control Kit:
Heating Solutions:

• RAPT Temperature Controller

• 30W Heating Wrap

Cooling Solutions:

• Temp Twister Cooling/Heating Coil

• Temp Twister Pump Kit

This collection container fits all the FermZilla Tri-Conical fermenters that have a 3 inch x 3 inch butterfly valve. No more threads or removal tools to get this off, simply depressurise and remove the tri-clamp fitting. We'd recommend placing a towel or upside down frisby to catch some drips.

The clear body is made from Tritan from Eastman Plastics.  This heat tolerant plastic is BPA, and plasticiser free.

The ports on the side of this collection container are the same as a standard coke bottle or soft drink bottle.  These are also the same on the top of the FermZilla.
We would recommend using the following two items (not included) on your collection container for the average user:
1 x Red Ball Lock Plastic Carbonation Cap x 6.35mm duotight
1 x PCO1881 Gas Pressure Relief Valve Cap (PRV) and Pressure Relief Valve 35PSI (Red)


Includes:
1 x 600mL Tritan plastic collection container with 3" tri-clamp ferrule and 2 x Vertical PCO1881 Carbonation Cap Ports
1 x 3" tri-clamp clamp (3-Piece)
1 x 3" tri-clamp beaded seal
1 x 3" tri-clamp black POK end cap

Dimensions:
170mm High
Tapered from 3 Inch tri-clamp down to 66mm

From: Kegland

FermZilla 55L Tri-Conical Starter Kit - Generation 3.0

Introducing the Gen3 FermZilla Tri-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and redesigned tri-clover dump valve. This unit was born from customer feedback we received on the Gen2 Model. No more complicated dump valve designs here, just simplicity. Brew with confidence on the new Tri-Clamp FermZilla Range.

The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget.  With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.
This is an incredible product at an extremely attractive price point in all the different sizes and models.

The FermZilla 55L Tri-Conical can be used in the following ways:

• Basic Gravity Fermenter - New Brewers
• Pressure Brewing Kit - Most Popular
• Hop Bong Pressure Kit - For Intermediate Brewers
• Glycol Twister Pressure Brewing Kit - Glycol Obsessed

What's new the difference between Gen2 and Gen3?
1. Molded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch to 2 inch tri-clamp Butterfly Valve
3. 2 inch tri-clamp compatible Collection Container

Is it easier to clean / take apart than the Gen2?
YES, It is by far the easiest Conical PET fermenter to disassemble and clean into all the nooks and crannies. Simply release all pressure inside the vessel and detatch the tri clover clamps.

What does the starter kit come with?
      1 x 55L Conical FermZilla Tri-Conical Base Kit (unassembled)
      1 x 55L Gen 3 Tri-Conical Tank with metal neck ring
      1 x Standard Top Lid, with Red PRV (35psi) [2 x Male PCO1881 Cap Threads] [Up to 4 drill ports for accessories]
      1 x Collar Lid Ring
      1 x Grommet PCO1881 Black Cap + 1 x Blank PCO1881 Black Cap for lid
      1 x Premium 3 Piece Airlock
      1 x 3 inch tri clover to 2 inch tri clover Butterfly Valve
      1 x 1000mL Collection Container & Lid* [2 x Male Cap Threads]
      2 x Blank PCO1881 Black Cap
      1 x Brewbuilt Flex Container lid with 2 inch tri-clover ferrule.
      1 x 3 piece ~ 3 inch tri clover clamp [+ 1 x 3" Beaded Silicone Seal]
      1 x 2 piece ~ 2 inch tri clover clamp [+ 1 x 2" Beaded Silicone Seal]
      1 x Stainless Stand with swing handles
      1 x Stainless Steel Handle Assembly
      1 x Strip Stick On Thermometer
      1 x Level indicator sticker (Litres and Gallons)
      1 x Spare Lid O-Ring
      1 x Spare Collection Container O-Ring

Instructions:
To download the instruction sheet for this product click on the link below:
FermZilla 55L - Tri-Conical PDF Instruction Manual

Dimensions:

To download the dimensioned drawings for this product click on the link below:
FermZilla 55L Tri-Conical Dimensioned Drawing

Warnings:
Please read the instructions thoroughly before use.

• The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.
• Keeping the units out of direct sunlight is a must for all PET fermenters. Sunlight degrades PET.
• Do not expose to temperatures exceeding 35°C and pressure ferment past 5psi at these temperatures.
  

Please note:
When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage. 

Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.

From: Kegland

The FermZilla All Rounder 30L is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. It's far more capable than the FermZilla Flat bottom but it's less complicated and less expensive than the FermZilla Conical Unitank. So like the name says it's the "All Rounder".

If you want to use this product under pressure we would recommend that you use the pressure kit.

This kit includes:

• 1 x All rounder tank
• 1 x Stainless Steel Handle Assembly
• 1 x 304 stainless stand
• 1 x Airlock
• 1 x Pressure rated lid
• 1 x Digital temperature sticker
• 1 x Red 2.5bar pressure relief valve
• 1 x Graduation Sticker

Easy to Clean

This fermenter is made from super smooth PET so it's easy to clean. Just use a small scoop of PBW or similar and wipe it clean after a 5 minute soak. No scrubbing necessary.

Large 120mm Opening

The opening at the top is significantly larger then the older Snub Nose or other similar fermenters. This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.

Pressure Rated

This fermenter is rated up to 2.5bar so you can force carbonate just like a keg. You can use this fermenter for closed transfers and significantly reduce oxygen exposure.

Crystal Clear

The wall of the All Rounder is crystal clear so you can see what's going on inside. This makes it really easy to determine visually how the fermentation, how the yeast is flocculating etc.

Impermeable

The PET plastic is not permeable like some other fermenters made from PP or HDPE. The fermenter wall is a much better gas barrier keeping your product fresher for longer.

No Flavour and Aroma Carry Over

Other HDPE fermenters tend to be so porous they carry flavour and aroma from one batch to another.

Robust and Difficult to Damage

Impossible to smash like glass. The tank is impact resistant but light weight and easy to use.

IMPORTANT NOTE: This tank should not be used for hot liquid. Do not put liquids inside this tank over 50C. It will melt the tank. Also, while this tank comes pressure tested we recommend that every 2 years you re-hydro test this tank yourself.

From: Kegland
Diameter: approx. 352mm
Height: approx. 569mm (from stand base to top of airlock) or 614mm with stand reversed

The FermZilla All Rounder 60L is the perfect fermentation vessel that can be used for fermenting under pressure, carbonating and dispensing. It's far more capable than the FermZilla Flat bottom but it's less complicated and less expensive than the FermZilla Conical Unitank. So like the name says it's the "All Rounder".

If you want to use this product under pressure we would recommend that you use the pressure kit.

This kit includes:

1 x All rounder tank
1 x Stainless Steel Handle Assembly.
1 x 304 stainless stand
1 x Airlock
1 x Pressure rated lid
1 x Digital temperature sticker
1 x Red 2.5bar pressure relief valve
1 x Graduation Sticker

Easy to Clean
This fermenter is made from super smooth PET so it's easy to clean.  Just use a small scoop of PBW or similar and wipe it clean after a 5 minute soak.  No scrubbing necessary.

Large 120mm Opening
The opening at the top is significantly larger then the older Snub Nose or other pressure fermenters.  This bad boy has 120mm opening so even brewers with large arms can easily get into the top making cleaning even easier.

Pressure Rated
This fermenter is rated up to 2.5bar so you can force carbonate just like a keg.  You can use this fermenter for closed transfers and significantly reduce oxygen exposure.

Crystal Clear
The wall of the All Rounder is crystal clear so you can see what's going on inside.  This makes it really easy to determine visually how the fermentation, how the yeast is floculating etc.

Impermeable
The PET plastic is not permeable like some other fermenters made from PP or HDPE.  The fermenter wall is a much better gas barrier keeping your product fresher for longer.

No Flavour and Aroma Carry Over
Other HDPE fermenters tend to be so porous they carry flavour and aroma from one batch to another. 

Robust and Difficult to Damage
Impossible to smash like glass.  The tank is impact resistant but light weight and easy to use.

Please read the instructions thoroughly before use. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.

IMPORTANT NOTE: This tank should not be used for hot liquid.  Do not put liquids inside this tank over 50C.  It will melt the tank.  Also this tank comes pressure tested however we recommend that every 2 years you re-hydro test this tank yourself.  

Note: Some of the photos are of the FermZilla - All Rounder 60L with a red plastic pressure kit. The pressure kit is not included in the standard kit.

From: Kegland

This handy little strap will make cleaning and transport your FermZilla All Rounder 30L or 60L an absolute breeze. Simply attach through both sections of the base in the orientation you wish. Slide up and out of the little buckle pieces making sure that the buckle is facing towards you, then strap in and strap down!

The Strap is long enough for the 60L and 30L. We recommend rolling up the excess strap and paper clipping or cutting to suit the 30L. 

Please note the paper clips used in the photos are not included.

From: Kegland

A replacement FermZilla lid, made from glass reinforced engineering plastics that are not only chemical resistant, heat resistant but also tough as nails so they will last you a lifetime.

This lid is made from high quality plastic and will suit any of the FermZilla fermenters, uni tanks, bright tanks. It will suit:

FermZilla 27L - Conical Fermenter
FermZilla 35L - Conical Fermenter
FermZilla 55L - Conical Fermenter
FermZilla 27L - Flat Bottom
FermZilla 55L - Flat Bottom
FermZilla 27L - Bright Tank
FermZilla 55L - Bright Tank

Note: does not include the FermZilla lid ring that holds this down

From: Kegland

FermZilla - Replacement Lid Seal (OD 106mm x 2.65mm).

This thicker Lid O-Ring is suited to FermZilla Conical and All Rounder Models. 

If you have a brown O-Ring, this is a newer material that is softer and easier to fit. All units manufactured after 01/01/2023 will have this Brown O-Ring as standard

If you are experiencing leaking from the top lid section, this slightly thicker O-Ring will aid in resolving said leaking. To perform a leak test please remember to have the unit free of any liquid as that will absorb CO2.

It is also important to remember not to overtighten the stainless steel handles that may have come with your FermZilla. Overtightening will cause the opening to warp and not seal. The handles should be able to freely rotate around the neck with little resistance.

Note: this is for the seal only, lid not included.

From: Kegland

FermZilla 2" Tri-Clamp Lid.

Upgrade your FermZilla All Rounder or Tri-Conical fermenter with the new 2 Inch Tri-Clover Lid from Kegland. Add yeast, hops or even take samples from a wine thief from the top and not have to remove the entire lid.

This particular lid was designed in order to suit a growing number of customers dry hopping without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you would be able to purge CO2 into the tube and expel all the oxygen around it and dump freely into the vessel.

Features:
2 x PCO1881 Male Ports - Recommended to be used with 1 x Red (Gas) Ball Lock Cap and 1 x Yellow (Liquid) Ball Lock Cap.
1 x Pressure Relief Valve Port - Includes Red 35psi / 2.5bar PRV
1 x 2 Inch Tri-Clamp Ferrule 

Undrilled Ports:
1 x Thermowell Port (8mm duotight x 1/4" bulkhead) Suitable for 60cm Thermowell duotight Kit.
2 x Ice Water / Glycol Temp Twister Ports (9.5mm duotight x 1/2" bulkheads).

Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank. 

Also includes:
1 x 2 Inch Tri-Clamp x PCO1881 Male Thread with PCO1881 Bottle Cap
1 x 2 Inch Tri-Clamp Clamp
1 x 2 Inch Tri-Clamp Beaded Silicone Seal

Important:
- Release the pressure completely before opening the 2" Tri-Clamp.
- Only use KegLand Red 35psi / 2.5 bar PRV or KegLand Yellow 17psi / 1.5bar PRV's with this lid. Ensure they are cleaned and dried of sticky residue before each fermentation. Failure to do so could cause injury and void warranty.

From: Kegland

This jacket will keep your FermZilla All Rounder 30L cool in summer and warm in winter. It can also be used with a heater belt to warm up the wort if the heat from the fermentation isn't enough. To control the temperature, we suggest using a MKII Temp Controller.

This jacket also completely blocks any light/UV to prevent light struck or skunked beer.

From: Kegland

New FermZilla lid ring is a must in your home brewery! 

The Fermzilla Easy-Grip Threaded Lid Ring is the Swiss army knife you need in your fermenting space! This isn't any normal lid ring, this beast is built to be a fermzilla socket set!

Features:

Underside Hex holes
Use these to undo or tighten plastic carbonation caps on your fermzilla lid!

Ergonomic Handles
More leverage to easily undo the threaded lid ring! Comfortable to lift and move the fermenter.

Handy Hook
No need to use one hand or place the lid in sanitiser for pitching yeast or dryhopping. Simply use the hook to latch the lid onto the fermzilla opening. Now you have two free hands to work with!

Dry hop or pitch yeast with ease!

Carbonation Post hole
Easily pop stubborn lids out using leverage.

Fits both sizes of All Rounder and both sizes of Tri-Conical:
30L FermZilla All Rounder 
60L FermZilla All Rounder
Gen3 27L FermZilla Tri-Conical
Gen3 55L FermZilla Tri-Conical

Works with both the regular flat lid and TC lid:
FermZilla - Replacement Pressure Lid (NO RED PRV) - Suits Conical and All Rounder
FermZilla - 2 Inch TC Pressure Lid Kit

From: Kegland

2" Hop Bong Upgrade Kit For FermZillas - The Kriger (Warrior).

Named purely on its looks and not its function. The Hop Bong is a versatile pressurisable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters but also as an inline carbonation/oxygenation accessory.

This is an upgrade kit for existing FermZilla Tri-Conical and All Rounder fermenters users who want to use the new 2" Tri-Clamp Adapted Pressure Lid.

Constructed from Nylon 12: an autoclavable, extremely robust, and chemical resistant engineering plastic.

Includes:
1 x FermZilla Tri-Clamp Pressure Lid (including PRV, Bottle caps, 2Inch clamp, seal, PCO1881/Tri clover adaptor)
1 x FermZilla Tri-Conical - 2" x 2" Tri-Clamp Butterfly Valve
1 x Carbonation Cap PCO1881 (Red / Gas)
1 x 2 Inch Tri-Clamp - Hop Bong - Sight Glass
1 x PCO1881 PRV Cap
1 x Red PRV (35psi/2.5bar)
2 x 2 Inch Tri-Clamp Clamp
2 x 2 Inch Tri-Clamp Silicone Beaded Seal

Does not include:
1 x Carbonation Cap PCO1881 (Yellow / Liquid)
1 x Carbonation Cap PCO1881 (Red / Gas)
1 x SS Float + 80cm Silicone Dip Tube + Dip Tube Hop Filter

Please note that the Hop Bong is not made from glass. It is made from special engineering plastic.

Capacity in Hop Pellets
150g to 180g

From: Kegland

FermZilla Plastic Pressure Kit - suits both 27L and 55L FermZilla fermenters. This is the plastic version, there is also a stainless option.

Add this optional pressure kit to your FermZilla and turn your FermZilla into a true unitank. Unitanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. This extremely inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:

Fermenting Under Pressure: First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also a good idea to have two relief valves on the FermZilla anytime the unit is under pressure.

Carbonating, Pushing, and Serving: When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.

Lack of Oxidation Because the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.

Key Features:

• Ferment beer under pressure to reduce ester and fusel alcohol production
• Ability to always draw clear beer with the unique, floating draw tube
• Keg already carbonated beer
• Use co2 to push beer into a keg or though a filter into a keg
• Carbonate and serve beer directly from the FermZilla, eliminating kegging all together

Kit Includes:

1 x Red Plastic Carbonation Cap
1 x Yellow Plastic Carbonation Cap
1 x Float & Dip Tube Filter Kit

Add the optional pressure kit to your FermZilla and turn your FermZilla into a true uni tank. 

Uni tanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. 

Here are some possibilities:

Fermenting Under Pressure:

First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. 

Carbonating, Pushing, and Serving:

When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever.  You can also choose to send carbonated beer through a beer filter on the way to your keg.  When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.  

Lack of Oxidation

Because the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.  

Key Features:

•    Ferment beer under pressure to reduce ester and fusel alcohol production

•    Ability to always draw clear beer with the unique, floating draw tube  

•    Keg already carbonated beer

•    Use co2 to push beer into a keg or though a filter into a keg

•    Carbonate and serve beer directly from the FermZilla, eliminating kegging all together