This jacket is designed to insulate your FermZilla 55L fermenter during the colder months to keep your fermentation at the optimum temperature. It can also be used with a heater belt to warm up the wort if the heat from the fermentation isn't enough. It also completely blocks any light/UV to prevent light stuck beer.

From: Kegland

A replacement FermZilla lid, made from glass reinforced engineering plastics that are not only chemical resistant, heat resistant but also tough as nails so they will last you a lifetime.

This lid is made from high quality plastic and will suit any of the FermZilla fermenters, uni tanks, bright tanks. It will suit:

FermZilla 27L - Conical Fermenter
FermZilla 35L - Conical Fermenter
FermZilla 55L - Conical Fermenter
FermZilla 27L - Flat Bottom
FermZilla 55L - Flat Bottom
FermZilla 27L - Bright Tank
FermZilla 55L - Bright Tank

Note: does not include the FermZilla lid ring that holds this down

From: Kegland

FermZilla - Replacement Lid Seal (OD 106mm x 2.65mm).

This thicker Lid O-Ring is suited to FermZilla Conical and All Rounder Models. 

If you have a brown O-Ring, this is a newer material that is softer and easier to fit. All units manufactured after 01/01/2023 will have this Brown O-Ring as standard

If you are experiencing leaking from the top lid section, this slightly thicker O-Ring will aid in resolving said leaking. To perform a leak test please remember to have the unit free of any liquid as that will absorb CO2.

It is also important to remember not to overtighten the stainless steel handles that may have come with your FermZilla. Overtightening will cause the opening to warp and not seal. The handles should be able to freely rotate around the neck with little resistance.

Note: this is for the seal only, lid not included.

From: Kegland

FermZilla 2" Tri-Clamp Lid.

Upgrade your FermZilla All Rounder or Tri-Conical fermenter with the new 2 Inch Tri-Clover Lid from Kegland. Add yeast, hops or even take samples from a wine thief from the top and not have to remove the entire lid.

This particular lid was designed in order to suit a growing number of customers dry hopping without exposing the batch to oxygen from opening the lid. By using this lid in conjunction with the FermZilla 2" Butterfly Valve and Hop Bong Kit, you would be able to purge CO2 into the tube and expel all the oxygen around it and dump freely into the vessel.

Features:
2 x PCO1881 Male Ports - Recommended to be used with 1 x Red (Gas) Ball Lock Cap and 1 x Yellow (Liquid) Ball Lock Cap.
1 x Pressure Relief Valve Port - Includes Red 35psi / 2.5bar PRV
1 x 2 Inch Tri-Clamp Ferrule 

Undrilled Ports:
1 x Thermowell Port (8mm duotight x 1/4" bulkhead) Suitable for 60cm Thermowell duotight Kit.
2 x Ice Water / Glycol Temp Twister Ports (9.5mm duotight x 1/2" bulkheads).

Please Note: Temp Twister will need to be bent on a 20° Angle in order to fit on the curved lid and align vertically in the tank. 

Also includes:
1 x 2 Inch Tri-Clamp x PCO1881 Male Thread with PCO1881 Bottle Cap
1 x 2 Inch Tri-Clamp Clamp
1 x 2 Inch Tri-Clamp Beaded Silicone Seal

Important:
- Release the pressure completely before opening the 2" Tri-Clamp.
- Only use KegLand Red 35psi / 2.5 bar PRV or KegLand Yellow 17psi / 1.5bar PRV's with this lid. Ensure they are cleaned and dried of sticky residue before each fermentation. Failure to do so could cause injury and void warranty.

From: Kegland

This jacket will keep your FermZilla All Rounder 30L cool in summer and warm in winter. It can also be used with a heater belt to warm up the wort if the heat from the fermentation isn't enough. To control the temperature, we suggest using a MKII Temp Controller.

This jacket also completely blocks any light/UV to prevent light struck or skunked beer.

From: Kegland

New FermZilla lid ring is a must in your home brewery! 

The Fermzilla Easy-Grip Threaded Lid Ring is the Swiss army knife you need in your fermenting space! This isn't any normal lid ring, this beast is built to be a fermzilla socket set!

Features:

Underside Hex holes
Use these to undo or tighten plastic carbonation caps on your fermzilla lid!

Ergonomic Handles
More leverage to easily undo the threaded lid ring! Comfortable to lift and move the fermenter.

Handy Hook
No need to use one hand or place the lid in sanitiser for pitching yeast or dryhopping. Simply use the hook to latch the lid onto the fermzilla opening. Now you have two free hands to work with!

Dry hop or pitch yeast with ease!

Carbonation Post hole
Easily pop stubborn lids out using leverage.

Fits both sizes of All Rounder and both sizes of Tri-Conical:
30L FermZilla All Rounder 
60L FermZilla All Rounder
Gen3 27L FermZilla Tri-Conical
Gen3 55L FermZilla Tri-Conical

Works with both the regular flat lid and TC lid:
FermZilla - Replacement Pressure Lid (NO RED PRV) - Suits Conical and All Rounder
FermZilla - 2 Inch TC Pressure Lid Kit

From: Kegland

2" Hop Bong Upgrade Kit For FermZillas - The Kriger (Warrior).

Named purely on its looks and not its function. The Hop Bong is a versatile pressurisable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters but also as an inline carbonation/oxygenation accessory.

This is an upgrade kit for existing FermZilla Tri-Conical and All Rounder fermenters users who want to use the new 2" Tri-Clamp Adapted Pressure Lid.

Constructed from Nylon 12: an autoclavable, extremely robust, and chemical resistant engineering plastic.

Includes:
1 x FermZilla Tri-Clamp Pressure Lid (including PRV, Bottle caps, 2Inch clamp, seal, PCO1881/Tri clover adaptor)
1 x FermZilla Tri-Conical - 2" x 2" Tri-Clamp Butterfly Valve
1 x Carbonation Cap PCO1881 (Red / Gas)
1 x 2 Inch Tri-Clamp - Hop Bong - Sight Glass
1 x PCO1881 PRV Cap
1 x Red PRV (35psi/2.5bar)
2 x 2 Inch Tri-Clamp Clamp
2 x 2 Inch Tri-Clamp Silicone Beaded Seal

Does not include:
1 x Carbonation Cap PCO1881 (Yellow / Liquid)
1 x Carbonation Cap PCO1881 (Red / Gas)
1 x SS Float + 80cm Silicone Dip Tube + Dip Tube Hop Filter

Please note that the Hop Bong is not made from glass. It is made from special engineering plastic.

Capacity in Hop Pellets
150g to 180g

From: Kegland

FermZilla Plastic Pressure Kit - suits both 27L and 55L FermZilla fermenters. This is the plastic version, there is also a stainless option.

Add this optional pressure kit to your FermZilla and turn your FermZilla into a true unitank. Unitanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. This extremely inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:

Fermenting Under Pressure: First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also a good idea to have two relief valves on the FermZilla anytime the unit is under pressure.

Carbonating, Pushing, and Serving: When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.

Lack of Oxidation Because the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.

Key Features:

• Ferment beer under pressure to reduce ester and fusel alcohol production
• Ability to always draw clear beer with the unique, floating draw tube
• Keg already carbonated beer
• Use co2 to push beer into a keg or though a filter into a keg
• Carbonate and serve beer directly from the FermZilla, eliminating kegging all together

Kit Includes:

1 x Red Plastic Carbonation Cap
1 x Yellow Plastic Carbonation Cap
1 x Float & Dip Tube Filter Kit

Add the optional pressure kit to your FermZilla and turn your FermZilla into a true uni tank. 

Uni tanks are conical fermenters used both for fermentation and for carbonating and serving finished beer. 

Here are some possibilities:

Fermenting Under Pressure:

First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. 

Carbonating, Pushing, and Serving:

When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever.  You can also choose to send carbonated beer through a beer filter on the way to your keg.  When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator.  

Lack of Oxidation

Because the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock.  

Key Features:

•    Ferment beer under pressure to reduce ester and fusel alcohol production

•    Ability to always draw clear beer with the unique, floating draw tube  

•    Keg already carbonated beer

•    Use co2 to push beer into a keg or though a filter into a keg

•    Carbonate and serve beer directly from the FermZilla, eliminating kegging all together

The Temp Twister allows you to heat and cool your FermZilla or other fermenter or bright tank, ideally by combining with a glycol chiller. This coil can be adapted to fit any fermenter or bright tank that has an opening of 110mm diameter or larger. Simply drill to two 22mm holes in the lid of your fermenter and use the included Duotight bulkhead fittings to attach the coil to the lid of your fermenter. 

Specifications

• Coil Diameter x Height: 11cm x 68cm
• High Material: 304 Stainless Steel Coil
• Thickness: 9.5mm OD (3/8")
• Coil Length: 6 meters
• Heat Transfer: With this coil submersed in liquid it will be able to absorb more than 250watts

From: Kegland

FermZilla Temp Twister Lid - predrilled and including o-ring.

Take the pain and risk away from drilling your own Temp Twister Ports and Thermowell for your FermZilla. We've done the tricky work for you!

Does not include
1 x Red Gas Carbonation Cap
1 x Yellow Carbonation Cap
1 x Red 35psi OR 17psi Yellow Pressure Relief Valve (safety device)
1 x 60cm Thermowell Kit
1 x Temp Twister
1 x G20 Pump Up or G40 Pump Up/
1 x FermZilla All Rounder or Conical

Suits:
60L All Rounder FermZilla
55L Conical FermZilla
30L All Rounder FermZilla
30L Flat Bottom FermZilla (Not pressure rated)
27L Conical FermZilla

From: Kegland

FermZilla Tri-Conical - 2 Inch x 2 Inch Tri-Clamp Butterfly Valve.

Compatible with any 2 Inch tri-clamp fitting. Primarily designed for the:
- FermZilla 2" Tri-Clamp Lid
- in conjunction with the 2" Tri-Clamp Hop Bong

If you are looking to put your FermZilla Tri-Conical / All Rounder in a Fermentation Chamber / Fridge, you will want to allow 420mm measured from the base of the ring collar to a comfortable level to pull the pressure relief valve to purge oxygen from the hop bong.

From: Kegland

Economy 81 seat bottle tree with carrying handle made by Ferrari Group in Italy. The layers of the Economy bottle trees screw together for a very strong and stable unit.  Due to the handle you cannot set a sanitiser injector on top.

• Holds up to 81 bottles
• Can be used for beer or wine bottles
• Rotating base to easily load and unload bottles

A 10 inch filter housing for filtering your beer prior to bottling or kegging, or to filter water.

For beer this filter works best when used when transferring cold uncarbonated beer. All you will need to do is purchase some hosing, clamps, ball locks (if transferring to or between kegs) and a 1 Micron Filter to use this system.

- Clear high pressure housing
- Purge valve to expel air pockets
- ½” BSP inlet and outlet
- Includes Duotight 9.5mm (3/8"") fittings 
- Brass threaded ports for durability
- Compatible with other 10” filter systems

Note: you will need tubing to match the fittings (not included).

You will need a filter insert to use this system, like our 1 Micron Washable Filter (for filtering beer) or a 0.5 Micron Carbon Water Filter, (for water filtering).

Not suitable for hot liquids.

A rugged and durable push fit, inline filter strainer. 

Available in both 8mm and 10mm push fit size.

The detachable cap and body allow for easy servicing and cleaning.

Do not apply excessive vibration, torque, shock or other strong loads to the filter as the filter body may damage or collets may be dislocated.

Filter grade: 100 mesh
Colour: Black
Max. Pressure: 170psi
Temperature: Air -20C, Liquid 65C
Height: approx. 70mm

A 316 stainless steel washer. 

Dimensions: M12(13mm)x24x1.5

A 316 stainless steel washer. Fits over BSP Hex Nipple - 1/2 Inch.

Dimensions: M20(21mm)x37x1.6

FermZilla - SS Ball Float & 80cm Silicone Dip Tube and Filter Kit. Suits Tri-Conical and All Rounder Models.

This simple design allows you to extract the clearest possible liquid in your pressure vessel with the added security of our new filter included. This helps prevent blockages in your carbonation cap poppet. As the liquid level decreases the float goes down at the same time. Perfect for sampling the sediment free!

This 80cm silicone dip tube and stainless steel float with filter suits the FermZilla Tri-Conical fermenter. Also compatible with Kegmenters and Modified Ball Lock Kegs (not minikegs).

From: Kegland

This simple design allows you to extract the clearest possible liquid in your pressure vessel with the added security of our new filter included. This helps prevent blockages in your carbonation cap poppet. As the liquid level decreases the float goes down at the same time. Perfect for sampling the sediment free!

The new yellow cap is weighted to approximately 10g! Making it sink just that little bit lower to gain more liquid and less likely to suck air.

This 100cm silicone dip tube and stainless steel float with filter suits:
- FermZilla Tri-Conical 27L
- FermZilla Tri-Conical 55L
- FermZilla All Rounder 30L
- FermZilla All Rounder 60L
Also Compatible with Kegmenters, 50L Kegs and Modified Ball Lock Kegs (not minikegs).

From: Kegland

Large stainless steel funnel with a handle for bottling spirits. Also ideal for use with paper coffee filters if transferring oak aged spirits or spirit that has been polished on carbon. 

Specifications

• 14cm diameter, not including handle
• 12.5cm height
• Stainless Steel 
• Dishwasher Safe

This is the redesigned perforated grain basket for the G30 Brewing System which removes the need for a top plate and additional pipework. This basket comes as a standard with the G30v3 but can be purchased as an upgrade for previous versions of the G30 Brewing System.

Whats Included

• 1 x G30 Perforated Basket
• Bottom Grain Plate
• Silicone Recirculation Hose

Specifications

• Up to 8 kg (18 lb) grain capacity*
• Maximum batch size of 25 L of wort
• 304 Stainless Steel

*Grain capacity can reach 9 kg with a top plate (sold separately).

The Gas Ball Lock Post for Keg Coupler is a liquid ball lock post with a female 5/8 inch connection. It allows you to connect ball lock disconnects to a keg coupler making it extremely easy to swap over from a corney keg to a commercial keg (you will need the correct coupler for the keg as well). 

Gas Free Ball Lock Line Cleaning Kit

Are you ever in a situation where you don't want to unhook your gas line from your kegs, or have ball lock disconnects that you need to clean over at the sink but don't want to take your gas line all the way over there? Well, Kegland thought of a better way. Why not fill a PET Bottle with your cleaner / sanitiser and pump it without gas!

This little device can also be used as a mini party keg without a gas source (should be consumed well within 24 hours of pumping). BYO Liquid disconnect, hose and picnic tap.

Contains:
1 x KegLand Yellow Carbonation Cap
1 x KegLand PCO Tee Piece (Female x Male x Male)
1 x Mini Yellow Hand Pump
1 x 30cm Piece of EVABarrier Line 5mm ID x 8mm OD (can be stretched for larger PET bottles)

From: Kegland

GCAST allows you to break free from Bluetooth® range limitations giving you more flexibility on your brew day. GCAST is a wireless device that bridges the connection between your G30 controller and the Grainfather App on your smartphone using your Wi-Fi network giving you a more reliable connection so you can brew with confidence.

• More flexibility during brew days with a more reliable connection when brewing with the Grainfather App
• Break free from Bluetooth® limitations using your home Wi-Fi network
• Sleek, multi textured design, that can be attached to any magnetic surface
• Quick and easy to set up with no additional equipment to get started
• View live Tilt data from anywhere and log it to your brew session with no additional hardware required
• Backed by a 3-year warranty
• Includes 1m Micro USB cable (wall charger not included)

SIZE:

• 45 x 45mm

WEIGHT:

• 30g

POWER:

• Input voltage: 5V
• Current: 0.8A

MAGNETIC:

• Yes

WATERPROOF:

• No

MINIMUM SUPPORTED MOBILE VERSION:

• IOS: 11
• Android: 8

Reusable mesh bags for straining your grain or hops. Good for using with the brew in a bag (BIAB) method and can be tied or fitted over your vessel. Available in large and small sizes. The large fine bag includes a drawstring.

Small: approx. 300mm x 300mm (nylon)

Large: approx. 800mm x 550mm (polyester) - 63 micron mesh, suitable for boiling, up to 110C

Note: product may differ slightly from photo shown.

The MaltMuncher 2 Roller Grain Mill, featuring cold steel rollers with aluminium chassis. This Malt Muncher is adjustable to get your grain bill crushed exactly the way you want it. 10mm crank shaft as standard, perfect for the entry level millers wanting to use a drill to keep rolling.

Or if you want a work out and look like a pro arm wrestling champion, a manual crank comes as standard just to get you going.

If you are going to be using a drill, don't go crazy with speed, you can risk cooking/burning your grain and impeding the mills performance. If at all possible just enough power to get it going and catching. This should fall around the 200rpm mark.

Includes:
- Grain hopper (2.7kg capacity)
- Manual Crank handle
- 10mm crank shaft
- Roller adjustment knobs
- Reinforced chassis with pre aligned mounting holes for perfect stability if mounting to a board.
- 12 TPI knurl to efficiently pull grain through rollers while leaving hull intact to form an excellent filter bed for sparging

Comes flat-packed and requires assembly.

Note: does not include base board.

We also have the 3 Roller model.

From: Kegland

This item is not held in stock and is ordered in on request. Please contact to check availability and shipping cost. 

The G30ᵌ Advanced Brewing Setup includes the Grainfather G30ᵌ, the legendary all-grain Brewing System that took the home brewing world by storm. Designed to be advanced enough to please home brewing experts, but simplistic enough to cater for all experience levels. Plus, with the addition of the GF30 Conical Fermenter and GC4 Glycol Chiller, you’ll have a superior fermentation environment to achieve expert brewing results with every beer and the flexibility to control/monitor fermentation from anywhere thanks to built-in wireless control.

Compact and simple to use, with a small footprint for brewing indoors, the G30ᵌ Advanced Brewing Setup includes superior design, an impressive list of features and the latest technology. There is no limit to the types and styles of beer that can be made, and you’ll be able to brew professional, quality craft beer at home!

WHATS INCLUDED

G30ᵌ Brewing System:

• Counter Flow Wort Chiller
• GF30 Conical Fermenter

GF30 Conical Fermenter:

• Fermenter Lid
• Rubber Bung
• Bubbler Airlock
• Cone Plug
• Cone Plug Seal
• 5 cm (2") Tri Clamp
• Power Adapter and Wall Plug
• 2 m (6.5 ft) M12 3-Pin Power Cord
• Dual Valve Tap
• GF30 Conical Fermenter Controller

GC4 Glycol Chiller:

• Wall outlet power cord with plug
• 3 L propylene glycol
• Cooling connection couplers x 2
• 2 m insulated hoses x 2
• Glycol funnel
• Silicone tube for priming pump