Sort by:
PET plastic bottles are readily available and inexpensive. The standard thread for PET bottles for carbonated beverages between 0-3L in size is the PCO 1881 thread. This thread type suits our carbonation caps that you can buy in plastic here or stainless steel.
Historically you would only be able to place a black or grey ball lock disconnect onto these fittings one at a time. This tee piece now enables you to attach both a liquid and gas disconnect to the bottle at the same time so you can essentially use a common PET bottle as a keg.
Note: The PET soft drink bottle and dip tube are not included.
A 12.7mm compression fitting with 1/2" BSP thread.
These compression fittings are commonly used with immersion chillers to quickly disconnect the liquid hosing for storage and ease of cleaning.
This fitting is a part of the Grainfather Camlock Conversion Kit.
From: Kegland
Duotight - 6.5mm (1/4") x 8mm (5/16") Reducer.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
Duotight - 8mm (5/16") Female x 1/4" Male Thread Bulkhead (suits 60cm Thermowell)
$6.95
Unit price perDuotight - 8mm (5/16") Female x 1/4" Male Thread Bulkhead (suits 60cm Thermowell)
$6.95
Unit price perDuotight - 8mm (5/16') Female x 1/4' Male Thread Bulkhead (suits 60cm Thermowell).
Currently the Gen3 model.
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them. The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings. This makes these fittings even more reliable and reduces the chance of a leak significantly.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi
Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.
What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.
EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.
From: Kegland
Duotight - 8mm Female - 5-Way Multi-Tee
This particular Duotight tee saves on space and purchasing multiple generic equal tee's when setting up a 4-tap kegerator, or if you simply want to plumb up to four liquid or gas lines from one source.
Simply plumb your gas line in to any of the connections, then split it off to up to four different lines. If you want to cap off certain lines, we would recommend using an 8mm plug.
Flush mountable!
Looking for high quality push-in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Why do we use double o-rings?
The secret to the superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them. The double o-ring means we literally have twice the sealing surface when compared with other push in fittings. This makes Duotight fittings even more reliable and reduces the chance of a leak significantly.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes Duotight fittings the most reliable push fit fittings on the market.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.
EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA-free and is the number one choice for many long-lasting food-grade applications.
From: Kegland
Duotight 8mm OD retaining circlip, suits any Duotight 8mm fitting. When clipped into place, this circlip prevents the collar of the Duotight fitting from being pushed inwards, making it impossible for the fitting to release its grip on any hose!
Note: Duotight fittings, ball lock disconnects and hose sold seperately.
From: Kegland
Duotight - 8mm x 9.5mm Reducer.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
Duotight - 9.5mm (3/8") Female x 1/2" Female Thread.
It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
Note: colour may vary.
From: Kegland
Duotight - 9.5mm (3/8”) Female x ½" Male Thread Ball Valve.
It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
Note: colour may vary.
From: Kegland
Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread.
It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
Note: colour may vary.
From: Kegland
Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread Bulkhead (suits TempTwister).
Looking for high quaility push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them. The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings. This makes these fittings even more reliable and reduces the chance of a leak significantly.
The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues. This typically can be an issue with other fittings. This combination of factors makes duotight fittings the most reliable push fit fittings on the market.
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi
Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.
What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.
EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.
From: Kegland
The BlowTie Diaphram Spunding Valve - a great tool if you want to control the pressure retained in a pressure vessel that is releasing pressure. It has been designed for simplicity and ease of putting together. Many brewers use this spunding valve in combination with the FermZilla pressure rated fermenters.
This is the new "BlowTie 2" upgarded model which has the integrated pressure gauge. The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure. This BlowTie unit can be easily disassembled for cleaning using a screw driver. Designed to suit 8mm (5/16") tubing. It's compatible with both the 4mm ID Tubing or 5mm ID.
This compact solution for adjusting residual pressure in your fermenter makes pressure control easier than it's ever been. This can be used for compressed air, CO2, nitrogen, mains water supply and many other things but its primary use is to control the residual pressure inside fermenters.
Specifications:
1. Suits pressures 0-23psi (but with different gauges the unit can go above 100psi)
2. Made from food grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides
The design utilises the reliability of the Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.
Pressure Fermentations
With the popularity of pressurised fermentation it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.
Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg it is often a good idea to have head pressure in the keg you are filling into especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process.
Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation. Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.
The BlowTie has been made completely differently taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure.
Instructions:
Use the yellow adjustment knob to control the pressure coming out of the pressure vessel. Clockwise is higher pressure and anticlockwise is lower pressure. We would recommend gassing a keg to a known pressure e.g. 15psi then attach your BlowTie Kit to the keg and adjust to 10psi.
These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.
IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)
Material: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland
The Duotight Inline Regulator - these compact inline regulators have been designed to suit 8mm (5/16") tubing.
Suits pressures 0-150psi however this unit is packed with the 0-60psi gauge as standard. Suitable for mains water pressure, also suitable for liquid or gas.
- Made from Acetal/POM, EPDM o-rings and stainless teeth
- Suits 8mm (5/16) OD tubing
- Includes integrated 0-60psi Pressure Gauge
For higher pressures such as mains water supply we recommend the 4mm ID Tubing, or 5mm ID if you do not need as high pressures and you would prefer higher flow rate.
This compact solution for adjusting water and gas pressure can be useful in many different applications. It can be used for compressed air, CO2, nitrogen, mains water supply and many other things.
The design utilises the reliability of the Kegland patented Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.
These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.
IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)
Made From: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland
Duotight push in fitting for 8mm line to 5/8inch thread - ideal for keg couplers and tap shanks.
Duotight fittings feature a double o-ring sealing design for a more secure seal. The seals are not only high quality EPDM o-rings but also it has two of them. The double o-ring means there is literally twice the sealing surface when compared with other push in fittings. This makes Duotight fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that you can bend the hose with a much tighter radius without leaking issues.
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used for up to 100 psi.
This push in fitting will fit 8mm outer diameter tubing, while the thread on the other end will suit:
- MFL ball lock disconnects
- MKIII and MK4 regulators with MFL output
- Other fittings with MFL thread
No clamps necessary, but we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
Note: colour may vary.
From: Kegland
Duotight 8mm (5/16) one way check valve/non-return valve.
This very handy fitting could save your regulator and is a good investment. This particular type of check valve has low opening pressure of only 1 psi. It is suitable for clean liquids such as water or for gas. The spring and internal components are made with stainless steel and quality EPDM seals.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
Fits 8mm outer diameter tube.
Note: colour may vary.
From: Kegland
This Duotight Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
From: Kegland
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
Note: colour may vary.
This Duotight Push-Fit Tee - 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.
Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.
Fits 8mm outer diameter tube.
Note: colour may vary.
From: Kegland
Duotight - 8mm x 1/4 inch BSP Male.
No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.
These push in fittings are suitable to be used up to 100 psi.
These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.
From: Kegland
This manifold splits one line into two, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.
If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug
Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.
The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).
Not suitable for liquids other than filtered water.
Looking for high quality push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
From: Kegland
This manifold splits one line into four, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.
If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug
Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.
The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).
Not suitable for liquids other than filtered water.
Looking for high quality push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
From: Kegland
This manifold splits one line into six, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.
If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug
Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.
The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).
Not suitable for liquids other than filtered water.
Looking for high quality push in fittings that will seal tight? Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.
Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line
No clamps necessary!
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.
These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.
From: Kegland
This really handy device is great for filling kegs, keg to keg transfers or fermenter to keg transfers.
Fantastic for use with Fermentasaurus or other pressurisable fermenters.
Simply attach this device to the output gas post of your Keg then when the keg is full it will prevent further liquid exiting the gas post. This means you can literally set and forget and fill kegs automatically without the risk of kegs overflowing all over the floor.
For even better results we recommend this product to be used with the Duotight - BlowTie Diaphram Spunding Valve - Adjustable PRV. This blowtie spunding valve will also enable to to apply head pressure to the keg meaning you can control the flow speed but also reduce the foam generated in the filling process particularly for carbonated beverages like beer.
This flow stopper includes:
- 2 x duotight 8mm x 5/8 push in fittings
- 1 x ball float
- 1 x stainless spring
- 2 x straight 8mm joiners
- 1 x acrylic sight glass (with 5/8 male thread on either side)
FermZilla Tri-Conical - 2 Inch x 2 Inch Tri-Clamp Butterfly Valve.
Compatible with any 2 Inch tri-clamp fitting. Primarily designed for the:
- FermZilla 2" Tri-Clamp Lid
- in conjunction with the 2" Tri-Clamp Hop Bong
If you are looking to put your FermZilla Tri-Conical / All Rounder in a Fermentation Chamber / Fridge, you will want to allow 420mm measured from the base of the ring collar to a comfortable level to pull the pressure relief valve to purge oxygen from the hop bong.
From: Kegland
A rugged and durable push fit, inline filter strainer.
Available in both 8mm and 10mm push fit size.
The detachable cap and body allow for easy servicing and cleaning.
Do not apply excessive vibration, torque, shock or other strong loads to the filter as the filter body may damage or collets may be dislocated.
Filter grade: 100 mesh
Colour: Black
Max. Pressure: 170psi
Temperature: Air -20C, Liquid 65C
Height: approx. 70mm
A 316 stainless steel washer.
Dimensions: M12(13mm)x24x1.5
A set of tap adapters to enable tubing for the Grainfather Counterflow chiller to be connected to an indoor or out door tap.
Could also be used to connect tubing for other equipment, such as the Filter - Beer & Water Filtering System, to an indoor or out door tap.
Convert the Recirculation Arm and the Counter Flow Chiller of the Grainfather to convenient Camlock fittings.
This upgrade kit consists of 5 stainless steel parts to convert the Grainfather Recirculation Arm and Wort Chiller to easy to use Camlock fittings.
Watch David Heath's YouTube video above for more information and installation instructions.
Click here for an installation guide.
Kit contains:
-
BSP Hex/Reducing Bush 1/2 Inch - 3/8 Inch
- Camlock - Female to 1/2 Inch Female D Type
- Camlock - Male to 1/2 Inch Female A Type
- Camlock - Male to 1/2 Inch Barb E Type
- Compression Fitting - 12.7mm to 1/2 Inch BSP
Please measure the diameter of your Grainfather Recirculation Arm to ensure the compression fitting will fit.
For use with the G70 and G40 to allow quick drainage from the bottom of the unit. Made with high temperature resistant 304 grade stainless steel, the faucet’s operating temperature ranges from -10°C to 150°C.
Alternatively you could use the Ball Valve Assembly 316 Stainless Steel - 1/2 Inch.
This handy spring clamp has been the tool of choice for many KegLand employees to hold the malt pipe silicone hose in place during the mash.
Handy Clamp (4" Long) - ideal for use with a Brewzilla.
This clamp features a heavy-duty muslin spring which ensures your silicone hose never accidentally pops out of your mash tun and spills your precious nectar over your brewery floor.
It features rounded handles for a comfortable grip and a PE end grip to ensure your hosing is kept secure.
This clamp is made from PP and PE which have good chemical resistance so it will stand up to the task for use around common brewing cleaners and sanitisers such as StellarClean/PBW and StellarSan.
These spring clamps have a multitude of potential uses throughout your brewing outside of securing silicone hosing.
From: Kegland
