These 304 Stainless 2200w weldless elements are designed to fit a 32mm hole inside the wall of your brewing vessel or boiler. It comes bundled with the power cord.

We do recommend using a RAPT Temperature Controller to run this element with the appropriate thermowell or temperature probe attachment.

These electric brewing elements are highly recommended for your HLT, or even for a HERMS or RIMS setup. Multiple elements may be required for larger volumes and depending on what temperature you are trying to achieve. If you are going to be using these elements directly in your mash tun, and will try to maintain temperature using the element, we would recommend getting a power control chip 3600w to modify the power output to the element. Too higher power directly in contact with your malted grain can cause scorching/off flavours as the temperature may not be evenly distributed and isolated purely around the element itself.

Element Length: approx. 300mm
Diameter: approx. 25mm
Thread: approx. 32mm
From: Kegland

3600 Watt Stainless Steel Heating Element with 2 inch tri-clamp (220-240v)

It can be fitted to a 2" tri-clamp ferrule. It does have a water-resistant screw element guard. This was produced to be used with the 118L Kegmenter that has 2" ferrules.

It is highly regarded as a popular and reliable element for distillers and homebrewers.

This element is to be installed by a professional electrician with a 15amp Cord. 

From: Kegland

2" Tri-Clamp Sight Glass - Hop Bong with PCO1881 Male Port and black bottle cap.

Named purely on its looks and not its function. The Hop Bong is a versatile pressurisable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory.

This particular sized tri-clamp hop bong was designed for the FermZilla Tri-Conical and All Rounder fermenters with the new tri-clamp adapted pressure lid. It can also be adapted to any 2" tri-clamp port in your system to use either inline or as a dry hopping device.

Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic.

Depending on how you set up your Hop Bong, the most common two fittings for the PCO Port are the Duotight 6.35mm Red Gas Carbonation Cap or Duotight 6.35mm Yellow Gas Carbonation Cap , and the Red PRV Cap.

Please note that the Hop Bong is not made from glass. It is made from special engineering plastic.

Capacity in Hop Pellets
150g to 180g

From: Kegland

Now updated with the all new duotight 8mm Ball Lock Disconnect (Grey+Red/Gas)

This kit has been designed for simplicity and ease of putting together. 

This Kit Contains:
1 x BlowTie Spunding Valve Gen 2 with 0-15psi Integrated Gauge
1 x Duotight 8mm (5/16") x Ball Lock Disconnect (Grey+ Red/Gas)
1 x Rigid 8mm Plastic Joiner

All new compact BlowTie Spunding Valve Gen2 Integrated Kit. If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job. 

If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job.

The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure.

This BlowTie unit can be easily disassembled for cleaning using a Phillips head screw driver.

Designed to suit 8mm OD (5/16") Evabarrier Tubing. 

Specifications:
1. Suits pressures 0-15psi (but with different gauges the unit can go above 100psi)
2. Made from food-grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides

If you are looking for a compact digital gauge with backlight illumination click here. This should only be used on a blowtie if you have excess tubing to stop liquid reaching the gauge. If liquid enters the digital gauge it will break.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The Equal Tee 8mm can be used split gas lines or other tubing.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The FFL 1/4 Inch to 5/16 Inch (8mm) Push-fit connects to 1/4 inch MFL fittings such as the Beer MFL Ball Lock Disconnect and Gas MFL Ball Lock Disconnect and is suitable for use with 5/16 inch/8mm tubing.

Hand tighten only. Over tightening could damage the fitting.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

These valves have been designed to allow temporary servicing of downstream equipment and must only be used in the fully open or fully closed position.

DO NOT USE THESE VALVES: In a partially open position to control flow; to provide a permanent termination; without tubing assembled or plugged (or threaded connections sealed, or as a tap or “faucet”.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The Two Way Divider quickly and easily splits a line into two separate lines.

Hand tighten only. Over tightening could damage the fitting.

Clear lubrication gel for keg parts such as o-rings, couplers, party pumps. Use with plastic and rubber components to avoid cracks and extend their life. Just a little of this goes a long way.

Food grade keg lube is completely safe to use with all components. FDA listed, high quality, tasteless and odourless grease.

• Food safe lube for keg parts

• Use with both rubber and plastic parts to avoid easy damage

• Long lasting

• Keeps for years

Specifications

• Food Grade lubricant is safe for all home brewery needs

• Keeps rubber parts soft and supple

• Helps prevent leaks

Size: 1oz (28g)

Made in: Germany

Service temperature: -20C to +45C

From: Krome Dispense

Low Volume CIP Spinning Spray Rotor (stainless swivel nut and barb).

Introducing the new Low Volume CIP Spray motor. An inexpensive low-flow spray head for low voltage pumps as low as 6w up to 25w. The perfect spray head that has multiple uses over your brew day.

- Clean In Place (CIP) with your 35L, 65L or 100L BrewZilla (can be fitted to the other branded units)

What can it do?
Clean In Place your 35L, 65L or 100L BrewZilla. Simply cut your recirculation hosing, or purchase additional silicone hosing to get the right length for your setup. You will be able to find the optimum length required by testing with water first. We found great success using the glass lid to start with to see if it is coating everything that you need it to.

Specifications

1 x Custom molded rotating spray head with 1/2" BSP thread
1 x 300mm length silicon tubing suitable for your BrewZilla recirculation arm
1 x Stainless nut and barb

Please note: The rotating spray head can only be used in the downwards position, it cannot be tilted or mounted sideways or upside down.

From: Kegland

Mini Gauge 0-15psi (0-1.5bar) - for inline Duotight regulator or Blowtie.

This gauge is designed to fit into either our inline regulator or our Blowtie unit.  These can be used for water or gas.  

Specifications

• Pressure: 0-15psi (0-1bar)
• Graduations: PSI + Bar
• Material: Brass/Plastic/Copper Capillary
• Gauge Diameter: 20mm
• Probe Diameter: 7.8mm (designed to fit 8mm hole)
• Accuracy: These gauges are accurate to 10% of the whole pressure range.

WARNING:
Do not exceed gauge pressure.  If you exceed gauge pressure it will damage the capillary in the gauge and prevent the gauge from working correctly.  NEVER exceed the maximum gauge display pressure range.

Not tested or approved for pure oxygen.

If you are looking for a compact digital gauge with backlight illumination click here.

From: Kegland

Digital Illuminated Mini Gauge 0-90psi (0-6.2bar) - Duotight 8mm Stem.

Traditional analogue gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle.  This age old technique works quite well especially in large gauges, but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue.  With very small gauges, such as a 27mm x 27mm Mini Gauge, it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components.

Kegland has developed the worlds most compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor.  This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions is required.

Specifications:
Battery Life: More than 2 years (using the mini gauge once a day)
Battery Type: CR2032
Auto Battery Saver: YES, screen automatically turns off after 15sec
Size: 27mm x 27mm
Duotight Stem: 8mm

NOTE: This gauge is not suitable for measuring pressure of liquids.  It is only for measuring gas pressure.  If liquid gets into the pressure transducer it will damage the gauge.  If you want to measure liquid pressure you can purchase one of these analogue gauges:

KL07696 - Duotight Compatible Push in Pressure Gauge

From: Kegland

Digital Illuminated Mini Gauge 0-90psi (0-6.2bar) for Integrated Blowtie and In-line regulators.

Traditional analogue gauges require a small capillary mechanism where a small pipe expands and unravels under pressure. This in turn drives a mechanical cog to rotate the gauge needle.  This age old technique works quite well especially in large gauges but as this mechanism is manufactured smaller and smaller a tradeoff between accuracy and size becomes the issue.  With very small gauges such as a 27mm x 27mm Mini Gauge it's difficult to make them better than 10% accuracy due to the physical constraints of the mechanical components.

Kegland has developed this compact mini digital gauge with backlight illumination. This very compact design retains high accuracy while still meeting the desirable small form factor.  This meets the growing need as mini keg systems, mini regulators and other more compact keg dispensing solutions is required.

Specifications:
Battery Life: More than 2 years (using the mini gauge once a day)
Battery Type: CR2032
Auto Battery Saver: Yes, screen automatically turns off after 15sec
Size: 27mm x 27mm
Radial O-ring Stem: 7.8mm Bore

NOTE: This gauge is not suitable for measuring pressure of liquids.  It is only for measuring gas pressure.  If liquid gets into the pressure transducer it will damage the gauge.  If you want to measure liquid pressure you can purchase one of these analogue gauges:

This digital mini gauge can be used to upgrade your:
Blowtie Spunding Valve
Inline Regulator
Core 360 Mini Regulator

If you would like to use the mini gauge to attach to other hobbie projects then you should consider the Duotight Compatible Digital Mini Gauge with part number KL18081 that has the 8mm duotight push in stem.  This makes it easy to fit to other 8mm duotight fittings, tubing etc.

From: Kegland

Prevent gas or liquid leaks on your MFL connections with this Nylon Flare Washer Olive for MFL Fittings (1/4"). This washer fits inside MFL connections such as on the MKIII/MK4 multi gas regulators, MFL ball lock disconnects, barbed swivel nuts, and 8mm push fit MFL connectors.

From: Kegland

PCO1881 PRV Cap

This cap has been designed to be used with the PCO38 Tapping Head for the PET Mini Keg Range. 

As it is a standard PET bottle thread (PCO1881). it can also be used on the FermZilla Collection Container / Lid.

Use with any of the four PRV valves (sold separately) - 17, 35, 65, 100PSI.

Please Note: Never exceed the pressure capabilities of your vessel. PRV's are not spunding valves!

From: Kegland

PCO1881 Male x 2 Inch Tri-Clamp (POK)

For all you hop bongers out there. We have an end cap for all end caps! The Polyketone 2 Inch Tri-Clover x PCO1881 Male Thread (PET drink bottle thread like a Schweppes / Coca Cola bottle).

Perfect to use along side the 2" Tri-Clover Hop Bong
- PCO1881 PRV Cap with a Red 35psi Pressure Release Valve
- PCO1881 6.35mm duotight x Carbonation Cap RED for Gas
- PCO1881 6.35mm duotight x Carbonation Cap YELLOW for Liquid

This product is made from high quality engineering plastic and will last a very long time.  It's chemically resistant and also designed to resist impact and physical damage.

The thread specification on this product is the PCO 1881 (AKA Coke bottle thread).

From: Kegland

This handy PCO38 Tapping Head assembly is a great way to get into kegging. Using standard home brew ball lock disconnects this is convenient, light weight, robust and useful for wine, cocktails, beer, and other beverages.

This PCO38 tapping head assembly has been designed to suit standard PCO38 bottle necks.

The PCO38 keg system is a inexpensive keg system that utilises quality engineering plastics and efficient injection stretch blow mould processes to manufacture economical kegs and tapping heads for both home brewing and commercial beers.

This particular tapping head kit comes included with 2.5bar pressure relief valve, liquid and gas ball lock posts and dip tube.

The plastics used in the tapping head can withstand a wide range of chemicals used in the brewing industry and relatively high temperatures (over 100C).

NOTE: The keg shown in the photos is not included.

From: Kegland

3 x Quality hose connectors to fit your Pure Distilling condenser snap on hose fittings or other hose fittings.

A sealed pressure gauge is the most sanitary and safest solution for measuring pressure. Designed to prevent krausen from plugging the gauge, it ensures longer-lasting performance and unparalleled reliability.

This 1.5" tri-clamp pressure gauge can be used with any stainless steel fermenter with 1.5" tri-clamp ports. Liquid filled gauges offer better performance and longer lifespan compared to dry gauges.

The dial face reads in both psi and BAR.

From: Kegland

• 0-40psi / 0-250kPa / 0-2.5 Bar (kg/cm^2)
• Rubber Coated
• 8mm Push in Barb

In Line Regulator with 8mm push fit connections.

This unit has no gauge. Looking for the Duotight Inline Regulator with Gauge?

This inline regulator is suitable for gas or liquid. The design has two main features:

1. Push In 8mm
It comes with 8mm push fit connectors so you can push your beer, water, gas line directly into the unit.  No need for hose clamps, just push your EVABarrier line directly into the connector and it's securely joined.

2. Handy Tee Bar Adjustment
These have been designed with a highly visible yellow tee bar adjustment knob.  Significantly easier than the previous designs that required a phillips head screw driver to adjust the pressure.

Constructed with Non-Corrosive Acetyl, Nitrile & Stainless Components. The Regulator body has two wall mounting points.

These regulators work great for reducing your mains pressure from 0-159psi. The maximum inlet pressure is 150psi.

From: Kegland

Replacement camlock seals.

Material: Silicone

Supplier: Kegland

These washers are compatible with any 1/2 BSP plumbing hardware.

The silicone rubber in these washers is suitable for temperatures up to 250°C.

This is made from food grade silicone and will not perish like some other rubber washers.

Dimensions: 21mm(ID) x 31mm(OD) x 2mm (thickness)

From: Kegland

Stainless steel worm style hose clamp which fits a variety of hose types.

This hose clamp features a butterfly/key type adjustment tab which makes it easier to grip onto and tighten/loosen the clamp without the need for any tools.

If a larger diameter is required then multiple worm type hose clamps can be attached together.

Sizes available: 

• 14-25mm
• 21-38mm

From: Kegland

This hose fitting is made of stainless steel and connects three lengths of hose in a branch tee. The barbed fittings create a tight seal on flexible and semi-rigid hose when used with a hose clamp such as a stepless clamp. 

Bore sizes usually available:
- 6.35mm (1/4")
- 4.76mm (3/16")

Stainless Steel Quick Disconnect - Male to 13mm (approx. 1/2") Barb. Fits our Female Quick Disconnect.

Made from 304 stainless steel.

Stainless Steel Quick Disconnect - Male to 8mm Barb. Fits our Female Quick Disconnect.

Made from 304 stainless steel.

The advantage of these clamps is that the inner circumference is free of any steps or gaps, making them very useful on gas and beer lines for leak proof lines. 

Available in the following sizes:

• 10mm
• 10.5mm
• 11.9mm
• 13.3mm
• 17mm

You will need a Clamp Crimper tool for installation.

A stainless steel, 1/2" thread, weldless thermowell (takes any probe up to 7mm ID).

This thermowell works great with any kegmenter, keggle, brew pot, boiler and various other brewery hardware to get an accurate core temperature of your vessles.

This thermowell has a 7mm bore, so it's ideally suited to any probe type up to 7mm.  Most probes are 6.5mm or smaller in diameter meaning they will fit nicely into this well.  It's ideal for the RAPT Temperature controllers.

This is a weld free design so all you need to do is drill a 20mm hole and file this out a fraction and this will go right into the hole with no welding required.  The threads have been designed to be sanitary so you just screw it against your vessel wall and none of the threads will be exposed to liquid. The soft silicon seals will seal against curved surfaces of your pots and other vessels.

If you want to make a really smooth hole easily in your vessel walls we recommend the use of a step drill bit and 20mm hole punch.

Length: approx. 100mm
From: Kegland

A 1.5" tri-clamp thermowell fitting from Krome Dispense that is approx. 15cm long.

- 304 Stainless Steel
- Approx. 15cm thermowell

Does not include tri-clamp clamp or gasket.

From: Krome Dispense

This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.

Having the thermowell attach to the lid of a fermenter is ideal as it means the penetration through the fermenter body is at the top of the fermenter not below the liquid line. This makes the whole process more sanitary and reduces the number of difficult parts to clean.

This thermowell can be pushed through a bung with a 6-8mm hole but it also includes the Duotight bulkhead fitting that you can use to attach this thermowell to the lid of your FermZilla Fermenter.

It goes right into the middle of the core of your vessel meaning you get an accurate core reading of the liquid in the tank/vessel.

Note: If you need to shorten the length of this thermowell tube then simply use a tube cutter to the desired length.

Made from: 304 stainless steel
Dimensions: 8mm OD x 7mm ID
From: Kegland