Heavy Duty Vulcanized Latex Brewing Gloves - 55cm Long.

These heavy duty brewing gloves are made from vulcanized latex, ideal for cleaning around the brewery or even the home. Seriously long for getting those arms deep into Kegmenters, Fermzillas and those brew pots.

Tough chemical resistant material provides good protection to your hands during clean-up and sanitary handling of equipment. They are 55cm long so will also protect the forearm when reaching into harsh cleaning chemicals.

Weight: approx. 300gm
From: Kegland

The Heat Resistant Gloves / HIZO Oven Mitts are as impressive as they are functional with the ability to handle contact with temperatures of up to 500° Celsius (932°F). This means that it is perfect for use with oven baking, hot pots, grilling, barbecuing, and woodstoves.

Fashioned with high-quality aramid fibers which work to insulate and protect hands from burning temperatures, these gloves have a comfortable cotton and polyester lining which allows for breathability to resist sweating and a gauntlet-length style of design to protect wrists and forearm from scorching heat as well. These gloves are thick to provide excellent thermal protection and durability, but they are lightweight for extended use without fatigue.

Sizing: Medium only

With heat resistance up to 500°C, these gloves are perfect for:

• Perfect for oven baking, hot pots, grilling, barbecuing, and woodstoves
• Adjusting logs in the fireplace
• Touching scorching hot utensils or food while boiling or frying
• Changing light bulbs

Features:

• High-quality aramid fibers for insulation and cotton and polyester lining
• Designed for mobility and flexibility in mind
• Food-grade silicone layer
• Machine-washable, and can be easily hung on the line to dry

From: Kegland

This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla.

It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel. 

Diameter: approx. 66mm Heigh: approx. 300 mm.

From: Kegland

This polyester bag is perfect for small grain additions or for hopping beer. It is a tube of fabric that is approximately 15cm wide and 75cm long. Both ends are open for easy cleaning and can simply be tied closed while being used. Perfect for grain or hops (suitable for use up to 110 degrees C).

A hydrometer is an essential tool for testing starting and finishing gravity, or sugar content, in beer or wine or spirit fermentations. This is a triple scale hydrometer - specific gravity, potential alcohol and approx. sugar per litre.

Best used with a trial jar (sold separately).

Handcraft Supplies Triple Scale Fermentation Hydrometer measures the specific gravity, potential alcohol, and approx. sugar content of any fermentable liquid, whether you're making wine, cider, beer, or distilling wash. 

Best used with a trial jar (sold separately).

Infrared Thermometer Gun -50C to +580C (Black)

This thermometer gun has a built-in Dual laser that can be switched On and Off. Dual laser is an important feature when choosing infrared thermometers because it allows for much higher accuracy of readings. When measuring an object a Dual Laser will help greatly in finding the convergence point of the measured target and the spot ratio, which can only be achieved with Dual Laser.

Features:

• Double Laser pointer for accurate target aiming
• Simple one-handed operation
• Laser ON/OFF Switch
• Low battery indication
• LED backlight system for operation under poor illumination
• C° / °F temperature unit conversion
• Automatic Power off in 15 seconds without any operation
• Display hold, scan function

Note:
1. When using this product to measure temperature, consider the ratio between the distance (the length from the product to the measured object) and the size of the measurement area, referred to as the object distance ratio. When the distance between the product and the measured object increases, the measurement area will increase accordingly.

2. If you want to use boiled water to measure the quality of the product, please note that when measuring boiling liquids, do not allow smoke or water vapour to contact the temperature sensing area, and keep the measurement angle at 45 ~ 60 degrees.

Specifications:

• Temperature Range: -50 to 550°C
• Accuracy: ± 2% or 2°C
• Distance Spot Ratio: 12:1
• Emissivity: 0.1~1.0(Adjustable)
• Response Time Wavelength: 500ms & (8-14) um
• Repeatability: ± 1% or 1°C
• Resolution: 1°C or 1°F
• Storage Temperature: -20-50°C
• Operating Temperature: 0-50°C

From: Kegland

The Mangrove Jack’s Hop Spider keeps hops together during the boil. It can be used on all appropriate sized boil pots, including the Grainfather.

Made with a coarser, 800 micron mesh, for maximum wort flow and increased hop utilisation. 

Specs
Diameter: 15 cm 
Length: 30 cm 
Material: 800 micron 304 grade stainless steel mesh, with stainless steel support band and single hook.

A stainless steel pump for the MKII 25watt High Temperature Magnetic Drive Pump from Kegland. 

This pump is constructed of food-grade materials and handles boiling wort. The impeller housing is made from polysulfone as it is a tough, food-grade plastic rated up to 120C. The magnetic drive acts as a clutch allowing the user to put back pressure on the pump to slow down flow. Since it is magnetic drive, it’s not self priming, you must put the pump under the level of the liquid source. 

This is an extremely efficient 1.1amp pump which can be run continuously at elevated temperatures. 

The magnetic drive ensures no lubricated bearings are in contact with the liquid at all, so you can be sure there is no chance of any contamination of the liquid being pumped, which is why this pump is ideal for home brewing.

An optional stainless steel pump head is also available.

Voltage: 240V-AC
Power: 25 watts
Max Head: 3.4m 
Max Capacity: 19L/min 
Fittings: 1/2" BSP

• High accuracy 0.1 degree C.
• Dual plugs so you can control heating and cooling devices with the one controller
• 2 x 10amp sockets on rear; one for heating and one for cooling
• Works from -45C up to 120C
• Comes with fully waterproof probe so you can immerse the probe in water
• Uses “50k ohm” Probe
• Manufactured in compliance with Australian Standards

Made from lightweight muslin, this bag is perfect for hops additions or for holding botanicals when making gin.

Measures approximately 38cm in length and 10cm in width

An Oxygenation/Aeration Wand is an easy to use tool for adding oxygen to your wort to help ensure healthy yeast growth.

The wand kit includes the 60cm stainless steel 8mm OD wand and the 2 micron aeration stone screws into the end using an MFL thread so it can easily be removed for autoclave or dipped in acid solution. The kit also includes a stainless clamp and 2 meters of vinyl tubing.

Note: You will also need an oxygen cylinder and regulator which are not included.

Stone: 2 micron

Wand Length: approx. 650mm total

Handcraft Supplies 45 cm Plastic Mixing Spoon for mixing homebrew ingredients. This food grade spoon measures approx. 45 cm / 18 inches allowing use in most fermenters up to 30 litres.

Chillout Threaded MKIV - Counterflow Chiller - 30 Plate Heat Exchanger.

The Chillout MKIV, now with new and improved male 1/2" threaded posts is the fastest way to chill your wort to yeast pitching temperature to get your fermentation off to a quick healthy start.

The Chillout is made from stainless steel and brazed together with pure copper. It also has ripples up and down each plate. This creates more surface area and improves heat transfer.

To clean connect water to supply to the port where your wort was coming out and backflush the unit for a few minutes to ensure that any residue has been completely washed out.

Remember to sanitise either with boiling wort, or a short flush with StellarSan before use. Do not clean with StellarSoda or leave Phosphoric Acid based sanitisers left to store inside the plate chiller.

If you require mounting bolts (two spots on the rear), please use a M5 bolts (not included).

Dimensions: 315mm x 73mm x 51mm (not including threads)
From: Kegland

A refractometer is used to test sugar concentrations in a solution. When light passes through a liquid it bends at an angle. Depending on the density of the liquid, this angle becomes more or less pronounced. Refractometers work using this property and translate this shifted angle of refracted light to fall on a graduated Brix chart that is viewable in the eyepiece. 

When brewing a refractometer allows you to take instant gravity measurements during mash, run-off, or during the boil. A valuable tool for all grain and extract brewers alike.

As the density of wort is not the same as a sugar water solution you may wish to calibrate your refractometer when measuring wort. Click here for more information on how to do this.

When making wine a refractometer makes it very easy to measure the sugar levels at the crush or of your must.

Using a Refractometer:

To use, apply 2-3 drops to the prism face, close the cover and wait 30 seconds. Look through the eye-piece - the line on the screen will show the Brix % and Specific Gravity reading.

Calibrate the unit to 0.0 Brix before use with distilled water.

This model comes with ATC (Automatic Temperature Compensation) allowing you to use the refractometer between 10 / 30 degrees Celsius so the temperature of the sample is irrelevant. 

Comes with:
- Carry case
- Pipette
- Calibration Screw Driver

Note: This tool is used to measure unfermented wort. Once alcohol is present in the wort, the use of a correction table is advised.  It is possible to use a calculator to convert the reading, however it may not be as accurate as a hydrometer reading.

Gen2 - 2400W Power Station 240V - Power Controller

The new and improved Generation 2 - 2400 watt Power Controller. Suitable for homebrewers, distillers and any other means of power wattage adjustment up to 2400 watt (standard 10 amp). If you do not know if your electrical device can be reduced in power without failing, contact the manufacturer or an electrician.

We highly recommend using this product with our 2200w Weldless Element. We do not recommend plugging this unit into anything higher than a 10amp plug. Therefore you cannot use a 3600w tri-clamp element with this unit. We should also point out that if you do use this on a BrewZilla or Digiboil, that you will only be able to reduce 10-30% worth of power before the display turns off. Once the display turns off, so do the elements.

Please note; we recommend using x1 element only per Power Station Controller. If you are looking to use multiple, please ensure you have multiple Power Controllers on different circuits. If you are unsure please ask an electrician or trained professional. DO NOT EXCEED 2400W WITH THIS CONTROLLER!

From: Kegland

The Red Reaper Counterflow chiller is the latest homebrew chiller on the market.

Red Reaper Counterflow Chiller (PEX / Copper) 9.5mm duotight compatible.

This particular CFC uses PEX tubing that is swaged/soldered to the copper wort pipe. Not only does this provide a superior method of connection compared to a clamp, but also ensures a lifetime guarantee that the mains water you're using to chill your wort down will never get to the pressures requires for the PEX to break.

Paired with the duotight 9.5mm range, you'll be able to attach your hose / camlock fittings within seconds.

This particular kit does not come with 9.5mm push in fittings.

Specifications:

• 5.6m Length
• Inlet / Outlet Size 9.5mm Duotight compatible barbs
• 3 x Rubberised Feet
• 1 x Hinged Hanger (for BrewZilla Handles)

Recommended Cleaners:
PBW Powder (Optimum 80°C) minimum contact time 5minutes. Remember to change the flow back and forth to really get the deepest clean possible. Rinse with the same temperature water.

We would always recommend to recirculate your last 15 minutes of the boil in your Red Reaper to sanitise it before applying cold water to the chiller.

Using the incredibly pressure and temperature resistant style of hosing used widely inplace of copper in the plumbing industry. Partly due to its flexibility and ease of manufacturing.

The Red Reaper A-PEX CFC is a chilling beast, with an internal copper tubing where you wort will recirculate. and cool down You'll get a large amount of heat transfer from the copper and the cold water passing in the opposite direction.

The typical design of a CFC is usually copper tubing housed within another tube. The outer tubing is fed with a cold water source flowing in one direction, while hot wort is pumped through the inner copper tubing in the opposite direction. The main benefit is efficient single-pass chilling from a rolling boil down to pitching temps. CFCs function similarly to a plate chiller but have a larger overall area for the wort to flow through. The benefit is the reduced risk of clogs from hops. The downside is they take up more space than a plate chiller.

What is PEX?
PEX tubing, short for cross-linked polyethylene, is a flexible plastic pipe used as an alternative to traditional copper or steel pipes for plumbing.

Do not store in sunlight. It will degrade the PEX overtime.
Do not store with StellarSan or any acidic products. It will break down copper.

From: Kegland

Replacement camlock seals.

Material: Silicone

Supplier: Kegland

Replacement Silicone Seal for 65L BrewZilla Boiler Extension (24L).

You'll find the Brewzilla Boiler Extension Kit here.

From: Kegland

Braided Reinforced Heavy Duty Silicone Hose - 10m Roll (12mm ID x 20mm OD).

Properties:
Odorless, tasteless and inert
Good Electrical and weatherability properties
Resists UV, Ozone, gases and moisture

Features:
Working Temperatures -60°C ~ 260°C
Working Pressure: 58-580 psi

Applications:
Commercial brewery hot and cold side transfers

Length: 10m
From: Kegland

Silicone hose for liquid transfer. It is resistant to constant high temperatures and will handle temperatures above boiling point, and has excellent chemical resistance. The soft silicon is easy to work with and seals very well.

Please note that this tube should not be used for pressure above 15psi (such as mains water pressure), and has a burst pressure of around 30psi.

Price is per metre unless specified.

This clear tubing has an internal diameter of 7mm and an external diameter of 11mm, and comes in a 3 metre pack

Silicone is a superior material to traditional vinyl tubing. Silicone is food-safe, heat-resistant, more flexible and easier to use. 

A Sparge Arm for use with the Ss InfuSsion Mash Tun. 

- 304 Stainless Steel construction
- Designed for gravity feed from HLT, or combine your own pump / flow control valve
- 3/8” diameter stainless tubing
- Custom silicone handle mount for Ss Mash Tun
- Easily adjust height of sparge head up / down
- Uniform liquid dispersion from sparge head

The Ss Tri-Clamp Brew Kettle is constructed from 304 stainless steel and features an aluminium core tri-clad bottom to foster even heating and minimise the risk of scorching and allow for the use of induction heating.

Tri-Clamp ports have long been the standard in professional brewing, and for a good reason, they're quick, sturdy, and sanitary. The Ss Tri-Clamp Brew Kettle now brings this pro-level feature to the home brewer in an affordable package.

The sturdy riveted silicone-coated handles are now located on the front and back for easy moving and dumping of the kettle while also allowing for tighter brew stand setup. Just like the original Ss Brew Kettle, the tri-clamp version features an integrated trub dam into the dip tube to minimise the pickup of trub and hop material during knockout. The result is much clearer wort making its way into the fermenter.

Features:
- Tri-Clad bottom
- Sanitary tri-clamp ports
- Sturdy riveted silicone coated handles
- 3 piece tri-clamp ball valve with trub dam pick-up tube
- Lid designed to hang on side of handles
- Etched volume markings gals/litres
- Induction burner compatible

Available in these sizes:
- 38 Litre (10 Gal)
- 57 Litre (15 Gal)

Ss Brewtech recommends using Trisodium Phosphate (TSP) (sold separately) for initial cleaning to remove oils, grease and any manufacturing residue.

A stainless steel immersion chiller is a great piece of equipment for all-grain and extract brewers to cool the wort at the end of the boil. It is immersed into the boiling wort at least 10 minutes before the end of the boil (this will help to sanitise the chiller, although it should be clean before being used) and attached to a cold water source.

When ready to cool the wort, turn on the cold water and it will flow through the immersion chiller and cool the wort.

To increase the rate at which the wort cools you can stir the wort to create a whirlpool. This will cause more of the wort to come into contact with the chiller and cool the wort faster. Make sure to sanitise whatever you use to stir the wort.

You could also use a pump (such as the MKII 25w High Temp Magnetic Pump) to create a whirlpool immersion chiller; made popular by award winning American home brewer Jamil Zainasheff. Here is a link to Jamil's site, Mr Malty, with more details.

An immersion chiller can also be used to pre-chill the cooling water. Just submerge the immersion chiller in an ice bath to to pre-chill the water that ultimately flows into another immersion chiller in the wort. This can be particularly helpful during summer when the groundwater temperature increases.

A quality mash paddle is an essential piece of equipment for all-grain brewers. 

This high quality stainless steel mash paddle is approximately 61cm long and will make stirring the mash and avoiding dough balls a much simpler task. Avoiding the formation of dough balls during the mash is important to ensure the full extract potential of the mash is achieved. 

The paddle is also perfect for all other stirring duties and may even be used to knock down the hot break at the beginning of the boil.

Stainless Steel Quick Disconnect - Male to 13mm (approx. 1/2") Barb. Fits our Female Quick Disconnect.

Made from 304 stainless steel.

Stainless Steel Quick Disconnect - Male to 8mm Barb. Fits our Female Quick Disconnect.

Made from 304 stainless steel.

This is a high quality stainless steel spoon with long handle approximately 53cm in length.

It is well suited to all stirring duties and can be used to take samples from the mash tun or boil kettle. 

It is made of heavy-duty stainless steel so it will not warp due to heat, and is corrugated to help prevent it from bending.