Camlock - Male to 1/2" Barb (E Type).

Camlock fittings provide an easy way to make connections between your kettles, chillers, pumps, and other parts of your brewery.

Camlock - Male to 1/2" Female (A Type).

Camlock fittings provide an easy way to make connections between your kettles, chillers, pumps, and other parts of your brewery.

This fitting is a part of the Grainfather Camlock Conversion Kit.

Made from: Stainless Steel 316

A 12.7mm compression fitting with 1/2" BSP thread.

These compression fittings are commonly used with immersion chillers to quickly disconnect the liquid hosing for storage and ease of cleaning.

This fitting is a part of the Grainfather Camlock Conversion Kit.

From: Kegland

A copper immersion chiller is a great piece of equipment for all-grain and extract brewers to cool the wort at the end of the boil. It is immersed into the boiling wort at least 10 minutes before the end of the boil (this will help to sanitise the chiller, although it should be clean before being used) and attached to a cold water source.

When ready to cool the wort, turn on the cold water and it will flow through the immersion chiller and cool the wort.

To increase the rate at which the wort cools you can stir the wort to create a whirlpool. This will cause more of the wort to come into contact with the chiller and cool the wort faster. Make sure to sanitise whatever you use to stir the wort.

You could also use a pump (such as the MKII 25w High Temp Magnetic Pump) to create a whirlpool immersion chiller; made popular by award winning American home brewer Jamil Zainasheff. Here is a link to Jamil's site, Mr Malty, with more details.

An immersion chiller can also be used to pre-chill the cooling water. Just submerge the immersion chiller in an ice bath to to pre-chill the water that ultimately flows into another immersion chiller in the wort. This can be particularly helpful during summer when the groundwater temperature increases.

A carbonation or aeration diffusion stone, either 0.5 or 2.0 micron. This can be used as a way to aerate your wort prior to fermentation, or to speed up carbonation of the finished beer. The barb fits 1/4" (6.35mm) ID tubing.

If you're looking for diffusion stones with MFL thread, you'll find them here.

From: Kegland

A carbonation or aeration diffusion stone, 2.0 micron, with MFL thread. This can be used as a way to aerate your wort prior to fermentation, or to speed up carbonation of the finished beer. 

If you're looking for barbed diffusion stones, you'll find them here.

From: Kegland

The DigiBoil (digital turbo boiler) is a quality made 304 grade stainless steel turbo boiler.

The 35 litre size is the total rated size to the brimful. If using the DigiBoil as a brew kettle do not fill to greater than 25L-30L to ensure you have sufficient head space to comfortably contain the hot break and avoid a boil over. 

The boiler has a quality made stainless tap with stainless barb and 1/2 inch thread so you can attach the wide range of half inch fittings such as camlocks.

The unit comes with a concealed element for easy cleaning.

The digital display can be set from 0℃ and up to 140℃ with 1℃ increments and 1℃ resolution on the display.

The side of the boiler is pre-marked with graduations in litres and gallons that are accurate to +/- 1 litre.

- Litre and Gallon Graduations
- Stainless steel tap with barb and 1/2 thread
- Dual element control (so you can adjust the power from 500watts, 1900watts or 2400watts)
- Easy to use
- Great for use as a hot liquor tank, boiler, or hot water urn
- Concealed element for easy cleaning
- Can also be used for sous vide cooking

Want to save some power?
You can also purchase the neoprene jacket/parka that fits this unit here. This will reduce your heat loss by about 200-300 watts.

This digital turbo boiler is a quality made 304 grade stainless steel turbo boiler.

The 65 Litre size is the total rated size brimful, so typically if you are using this as a beer boiler you would probably only fill it up to 50-60L so you had 5-10 litres of head space to boil comfortably.

The boiler has a quality made stainless tap with stainless barb and 1/2inch thread so you can attach the wide range of other half inch fittings such as camlocks and many other fittings that we can supply.

The unit comes with a concealed element for easy cleaning.

The digital display can be set from 0℃ and up to 140℃ with 1℃ increments and 1℃ resolution on the display.

The side of the boiler is pre-marked with graduations in litres and gallons that are accurate to +/- 1 litre.

- Litre and Gallon Graduations
- Stainless steel tap with barb and 1/2 thread
- Triple element control (so you can adjust the power from 500watts, 1000watts, 1500watts, 2000watts, 2500watts, 3000watts and 3500watts! )
- Easy to use
- Great for use as a hot liquor tank, boiler, or hot water urn
- Concealed element for easy cleaning
- Can also be used for sous vide cooking

Dimensions: 42cm diameter x 74cm high

You can also purchase the neoprene jacket/parka that fits this unit here. This will reduce your heat loss by about 200-300 watts.

Note: Out of the box this unit needs a 15amp power socket.  With that said you can convert this to a 10amp compatible device in two different ways.  You can either:

1. Purchase a device like an Ampfibian Mini 15amp to 10amp adaptor.  If you do this you will be able to run the Digiboil, however if you turn on all three elements you will trip the circuit breaker.  For this reason you will only be able to use a maximum of 2 of the elements. (not all three)

2. Alternatively you can remove the cord and replace the cord on this device with a 10amp cord, but if you do this you will need to disconnect the larger element resulting in 1300watts less power.

Digital instant read thermometer with folding probe.

A perfect pocket temperature probe for homebrewing and BBQ! Check the temperature of your mash, whirlpool additions, or use it to check the internals of that fine-looking lamb roast on the bbq! With a range of -50°C to 300°C you will be hard-pressed not to get a temperature reading.

Specifications:

• Range: -50°C ~ 300°C / -58°F ~ 572°F
• Resolution: 0.1°C
• Temperature Error: +-1°C (0~100°C)
• Power Supply: AG13 button battery x 1 (included)

Functions:

• ON/OFF
• °C/°F
• HOLD

From: Kegland

This is the redesigned perforated grain basket for the G30 Brewing System which removes the need for a top plate and additional pipework. This basket comes as a standard with the G30v3 but can be purchased as an upgrade for previous versions of the G30 Brewing System.

Whats Included

• 1 x G30 Perforated Basket
• Bottom Grain Plate
• Silicone Recirculation Hose

Specifications

• Up to 8 kg (18 lb) grain capacity*
• Maximum batch size of 25 L of wort
• 304 Stainless Steel

*Grain capacity can reach 9 kg with a top plate (sold separately).

GCAST allows you to break free from Bluetooth® range limitations giving you more flexibility on your brew day. GCAST is a wireless device that bridges the connection between your G30 controller and the Grainfather App on your smartphone using your Wi-Fi network giving you a more reliable connection so you can brew with confidence.

• More flexibility during brew days with a more reliable connection when brewing with the Grainfather App
• Break free from Bluetooth® limitations using your home Wi-Fi network
• Sleek, multi textured design, that can be attached to any magnetic surface
• Quick and easy to set up with no additional equipment to get started
• View live Tilt data from anywhere and log it to your brew session with no additional hardware required
• Backed by a 3-year warranty
• Includes 1m Micro USB cable (wall charger not included)

SIZE:

• 45 x 45mm

WEIGHT:

• 30g

POWER:

• Input voltage: 5V
• Current: 0.8A

MAGNETIC:

• Yes

WATERPROOF:

• No

MINIMUM SUPPORTED MOBILE VERSION:

• IOS: 11
• Android: 8

Reusable mesh bags for straining your grain or hops. Good for using with the brew in a bag (BIAB) method and can be tied or fitted over your vessel. Available in large and small sizes. The large fine bag includes a drawstring. The small bag does not have a drawstring.

Large: approx. 700mm x 400mm (polyester)
Small: approx. 300mm x 300mm (nylon)

Note: product may differ slightly from photo shown.

The MaltMuncher 2 Roller Grain Mill, featuring cold steel rollers with aluminium chassis. This Malt Muncher is adjustable to get your grain bill crushed exactly the way you want it. 10mm crank shaft as standard, perfect for the entry level millers wanting to use a drill to keep rolling.

Or if you want a work out and look like a pro arm wrestling champion, a manual crank comes as standard just to get you going.

If you are going to be using a drill, don't go crazy with speed, you can risk cooking/burning your grain and impeding the mills performance. If at all possible just enough power to get it going and catching. This should fall around the 200rpm mark.

Includes:
- Grain hopper (2.7kg capacity)
- Manual Crank handle
- 10mm crank shaft
- Roller adjustment knobs
- Reinforced chassis with pre aligned mounting holes for perfect stability if mounting to a board.
- 12 TPI knurl to efficiently pull grain through rollers while leaving hull intact to form an excellent filter bed for sparging

Comes flat-packed and requires assembly.

Note: does not include base board.

We also have the 3 Roller model.

From: Kegland

The Grainfather counterflow chiller is used after boiling the wort to cool it down fermentation temperature. The counterflow does this by acting as a heat exchange between the wort and water from your tap as you transfer the wort from your boil kettle to your fermenter. Because this is a one-step process of transferring and cooling, it is more efficient and more sanitary than immersion chillers, and the curved design allows for similar performance to plate chillers without the crevasses that can make cleaning painful.

Features  

• One step transferring and cooling 
• Fast cooling time to within 3C of source water temperature. 
• More sanitary transferring 
• Copper inner coil for high heat exchange 
• Compatible with a range of brewing systems 

Includes

• Counterflow chiller
• G30 connector  
• 9mm right angle hose barb connector for G40, G70 and other brew systems
• Tap adapter set for connection to garden hoses and most faucets 

Specifications

• Copper inner coil
• 9mm ID inlet and outlet hoses
• Colour coded hoses for inlet and outlet water 

The Electric Grain Mill is motorised, compact and easy to use at home. It’s equipped with large, fluted rollers that crack the outer husk of the grain longitudinally, providing optimal surface area for your mash and a better filter bed for your sparge.

The removable grain hopper holds up to 1kg of grain at a time and with 10 easily adjustable gap settings, ranging from 0.8mm to 2mm, this mill has been engineered to crush a variety of grains. Crush different base malts and specialty grains, and even change the rate that your grain is crushed with the variable speed dial.

It’s easy to mount onto a workbench or bucket, but it works best with the Grain Mill Bamboo Mounting Board. Plus, the mill is easy to assemble thanks to its built-in motor and compact design. Simply attach the grain hopper. Set your desired gap setting by pulling the spring-loaded pin and rotating the dial. Add grain to the hopper and flick the switch to begin crushing.

For more information on assembling and using the Electric Grain Mill, watch our YouTube video here.

Now you can create fresher batches of beer by bulk buying your own grain and crushing it at home, just before you brew.

Specifications

• Voltage: 220 - 240V
• Frequency: 50Hz
• Power: 400W
• Rollers: 58mm diameter and made of hardened stainless steel with a flute design that’s akin to commercial grain mills
• 10 mill gap settings: 0.8mm - 2mm
• Crush rate: up to 1.7kg of grain per minute
• Grain hopper capacity: 1kg

Upgrade the Grainfather G30 Brewing System with the G30 Hop Plate, a purpose-built false bottom style hop plate filter for use with all G30 Brewing Systems. Install alongside the system's current filter for increased efficiency in hop filtration. 

 How to Use: 
1. Install the G30 Filter (this is the hop filter included with the G30) as per the instructions included with the G30 Brewing System.
2. Install the G30 Hop Plate by placing the plate feet down into the boiler over the top of the G30 filter, so the feet of the hop plate rest flat on the base of the boiler. 

Features:

• Sleek, high-quality 304 grade stainless steel construction
• Easy to clean
• Full body false bottom style filter for even better hop filtration
• Designed specifically for use with the G30 Brewing System

Specifiations:

• 304 stainless steel construction: (0.9 mm Thickness)
• Outer diameter (width): 29.5 cm
• Height: 5.1 cm
• Perforation diameter: 1.8 mm
• Carton dimensions: 32 cm x 32 cm x 0.9 cm"

Note: Some users may experience a slight reduction in boil vigour and a slight increase in heating time.

Caution: Post-boil hop matter will retain heat. Always use thermally insulated gloves when removing the hop plate post boil.

Upgrade your G30 and enhance your brewing experience with these rolled plates. Replace the standard G30 plates that come with silicone seals and make assembling and cleaning your grain basket a whole lot easier.

• 304 grade stainless steel
• Rolled edges
• Outer diameter (width): 267mm

Replacement rolled edge grain plate with handle for the Grainfather G30v3. This plate is to be used with the perforated grain basket and can be used as a top and bottom plate. Not recommended for use with G30 baskets pre G30v3.

Stock ETA: 04/09/2025

The G30v3 is an all-grain brewing system with a 30L (8 US Gal) capacity, designed to make up to 40 pints (23L or 6 US Gal) of high-quality beer from one brew. With app integration, innovative features, and an intuitive design, it’s perfect for both beginner and experienced brewers.

FEATURES

• Sleek 304 grade stainless steel body
• Manage your brew day from your mobile device via Bluetooth using the Grainfather App
• Get a more reliable connection between your G30v3 controller and the Grainfather App on your smartphone with the GCAST Bluetooth Wi-Fi Bridge
• A robust magnetic drive pump for maximum brewing efficiencies
• NEW perforated grain basket negates the need for a top plate or additional pipework
• NEW auto reset switch avoids the need to get underneath the unit should an unexpected trip occur
• Unlock distilling capabilities with the Still Spirits Alembic Dome & Condenser
• Available in both 220V and 110V in the US
• Backed by a 3-year warranty

Compatible with:

• GF30 Conical Fermenter
• GSERIES Glycol Chillers
• GCAST Wireless Bridging Device
• SF50 Conical Fermenter
• GCA Glycol Chiller Adapter
• Alembic Dome
• Counterflow Chiller (Highly recommended) The counterflow chiller is the simplest, most effective, and sanitary way to cool and transfer wort from your G30v3 to your fermenter in one step. If you have this, please see the instructions on the Counterflow Chiller box or refer to the G30v3 full instructions.

Whats included:

• Grainfather G30v3
• Bluetooth controller
• NEW perforated grain basket
• Grain plate
• Lifting bar
• Glass lid
• Recirculation pipe
• Filter
• Hose fittings
• Built-in pump

Specifications:

SIZE:

• 685 x 386mm (27 x 15’’)

WEIGHT:

• 14.6kg (32lb)

MAX PREBOIL VOLUME:

• 30L (8 US Gal)

BATCH VOLUME:

• Max: 25L (7 US Gal)
• Min: 10L (3 US Gal)

GRAIN BILL:

• Max: 8kg (18lb)*
• Min: 1.5kg (3.3lb)

*9kg (20lb) with top plate

POWER:

• NZ, AU, EU, UK, US: 2000W, 220V
• Also in the US: 1600W, 110V

CONNECTIVITY:

• Bluetooth Control

This item is not held in stock and is ordered in on request. Please contact to check availability and shipping cost.

The Grainfather G40 is a brewhouse brewing system that handles the hot side of the all-grain brewing process. This unit has the ability to produce up to 40L (11 US Gal) of wort from one brew. Connect your mobile device to the smart controller with built-in wireless control via the Grainfather App, for step-by-step brewing and access to 1000s of recipes.

The G40 is capable of transforming into a home distillery with the G40 and G70 Distilling Lid & Attachment Kits.

Add the Grainfather G40, G70 & SS Fermenter 1/2" Tap or Ball Valve Assembly 316 Stainless Steel - 1/2 Inch to enable quick drainage from the bottom of the unit making CIP a breeze.

Click here for the G40 instruction booklet.

Click here for the G40 technical specifications.

A replacement grain plate for the Grainfather G40 mash basket. Can also be placed on top of the grain in the mash basket (top plate) during mash recirculation and sparging. Also compatible with G70 v2.

This item is not held in stock and is ordered in on request. Please contact to check availability and shipping cost.

Requires 15amp power supply.

The Grainfather G70v2 is the ultimate 70L brewing system, allowing you to create enough high-quality beer to fill 122 pints in one brew. It’s the perfect match for experienced brewers, with built-in wireless connectivity so that you can connect to the Grainfather App for guided brewing and access to brewing tools, recipes and calculators. Now with a perforated grain basket, the G70v2 makes mashing even more efficient.

The Grain Mill Bamboo Mounting Board works great with the Electric Grain Mill. Mount the mill onto the board and place it over a bucket to catch your freshly crushed grain.

The Sparge Water Heater is a temperature controlled urn that allows you to heat up to 18 L of water making the brewing process even easier by having the right amount of sparge water heated to the right temperature ready at the time of sparge.

Start heating your sparge water when you begin the mash to ensure it is ready for when you need to sparge. Once water is at required temperature, it will hold that temperature until changed or turned off. Also comes with a sight glass, tap and heating lights.

NOTE: Graduations on the scale are measured from the tap.

Specifications

18 L Capacity
Stainless Steel Body
2 kw Element
Sight Glass (with 1 L graduations visible)
Tap
Temperature Control
Heating Lights (to indicate input temperature has been reached or is still being heated)

The 25L Sparge Water Heater is designed to be used with brewing systems of up to 40L, making it the perfect companion for the G40 or the G30. This temperature-controlled urn allows you to heat up to 25L of water in preparation to sparge, reducing the time and effort of heating additional sparge water during your brew, making your brew days even easier.

Specifications

• 304 grade stainless steel with a brushed finish.
• 25L capacity
• 2250W
• Heats up to 25L (6.6 US Gal) of sparge water in approx. 50 minutes.
• One piece structure for easy cleaning.
• Cool touch lid, with a twisted lock for safety purposes.
• Water gauge indication with an easy to use ball valve tap for dispensing water.
• 45-110°C variable thermostat to heat your water to the desired temperature.
• Heating lights to indicate when the temperature has been reached or still heating.
• Concealed heating element.

With the Grainfather Sparge Water Heater 40L, you can heat and keep up to 40L of sparge water at a specified temperature until it's needed. This means you can focus on the rest of your brew day, without having to worry about how or when you're going to heat a large volume of sparge water, and avoid the need to use 2 (or more) smaller volume heaters.

The unit heats up to 40L (10.6 US Gal) of sparge water in approx. 50 minutes, so you can simply start heating during the mash, and can forget about it until it's time to sparge.

Full Product Specs:

• Easy to read water level markings.
• Thermostat to heat water to your desired temperature, as well as boil.
• Easy to use ball valve tap for dispensing water.
• Heats up to 40 L (10.6 US Gal) of sparge water in approx. 50 minutes.
• 304 grade stainless steel.

Use in conjunction with the Grainfather Connect Control Box thermometer, for accurate control of your wort transfer temperature through the Grainfather Counter Flow Chiller. Avoid long lag time and off flavours by using the Grainfather Wortometer. Adjust your wort and water flow rates from the Grainfather Counter Flow Chiller by dialling in the exact wort temperature your specific yeast requires.  Requires a 8 mm inner diameter silicon hose. 

Click here to download the Wortometer Instructions.

These 304 Stainless 2200w weldless elements are designed to fit a 32mm hole inside the wall of your brewing vessel or boiler. It comes bundled with the power cord.

We do recommend using a RAPT Temperature Controller to run this element with the appropriate thermowell or temperature probe attachment.

These electric brewing elements are highly recommended for your HLT, or even for a HERMS or RIMS setup. Multiple elements may be required for larger volumes and depending on what temperature you are trying to achieve. If you are going to be using these elements directly in your mash tun, and will try to maintain temperature using the element, we would recommend getting a power control chip 3600w to modify the power output to the element. Too higher power directly in contact with your malted grain can cause scorching/off flavours as the temperature may not be evenly distributed and isolated purely around the element itself.

Element Length: approx. 300mm
Diameter: approx. 25mm
Thread: approx. 32mm
From: Kegland

3600 Watt Stainless Steel Heating Element with 2 inch tri-clamp (220-240v)

It can be fitted to a 2" tri-clamp ferrule. It does have a water-resistant screw element guard. This was produced to be used with the 118L Kegmenter that has 2" ferrules.

It is highly regarded as a popular and reliable element for distillers and homebrewers.

This element is to be installed by a professional electrician with a 15amp Cord. 

From: Kegland

Heavy Duty Vulcanized Latex Brewing Gloves - 55cm Long.

These heavy duty brewing gloves are made from vulcanized latex, ideal for cleaning around the brewery or even the home. Seriously long for getting those arms deep into Kegmenters, Fermzillas and those brew pots.

Tough chemical resistant material provides good protection to your hands during clean-up and sanitary handling of equipment. They are 55cm long so will also protect the forearm when reaching into harsh cleaning chemicals.

Weight: approx. 300gm
From: Kegland

The Heat Resistant Gloves / HIZO Oven Mitts are as impressive as they are functional with the ability to handle contact with temperatures of up to 500° Celsius (932°F). This means that it is perfect for use with oven baking, hot pots, grilling, barbecuing, and woodstoves.

Fashioned with high-quality aramid fibers which work to insulate and protect hands from burning temperatures, these gloves have a comfortable cotton and polyester lining which allows for breathability to resist sweating and a gauntlet-length style of design to protect wrists and forearm from scorching heat as well. These gloves are thick to provide excellent thermal protection and durability, but they are lightweight for extended use without fatigue.

Sizing: Medium only

With heat resistance up to 500°C, these gloves are perfect for:

• Perfect for oven baking, hot pots, grilling, barbecuing, and woodstoves
• Adjusting logs in the fireplace
• Touching scorching hot utensils or food while boiling or frying
• Changing light bulbs

Features:

• High-quality aramid fibers for insulation and cotton and polyester lining
• Designed for mobility and flexibility in mind
• Food-grade silicone layer
• Machine-washable, and can be easily hung on the line to dry

From: Kegland