Sort by:
A 5 litre glass jar suitable for small fermentations and the storage of spirits.
A Demijohn Bored Bung fits the opening of the jar perfectly enabling an airlock to be attached.
Add a Swing Lid or use a Demijohn Solid Bung as a stopper.
The Easy Syphon 3/8 Inch and Easy Syphon 350mm are both compatible with this demijohn.
Note: The handle and shape of the Demijohn may vary.
This 5 litre glass demijohn is perfect for small fermentations (4.5 litre / 1 gallon), the storage of spirits, and the aging/conditioning of wine or mead.
The Bung with hole #9.5 - 38mm-46mm or Bung - Bored - 37-45mm - Silicone fits perfectly to enable an airlock to be attached so the Demijohn can be used as a fermenter.
Compatible with both the Easy Syphon 350mm and the Easy Syphon 3/8 inch.
These 0.2 micron Air Filters have a fine enough filter membrane that they can filter out microbes and bacteria.
They can be used with any oil free air compressor such as a pond pump, or other type of pump.
These can also be used as an airlock in the top of your fermenter, or to filter air going back into a cask when dispensing real ale.
This filter is not suitable for liquids and should be discarded if it gets wet.
Barb diameter measures approximately 9mm - 9.5mm.
Standard S shape airlock for sealing your fermenter.
Please note that your fermenter will need an airlock grommet or top hat grommet (sold separately) to attach the airlock to most fermenters.
May not include red cap, depending on supplier.
The three piece airlock is a great choice for monitoring fermentation and stopping contaminant’s entering your fermenter. Easy to fill and disassembles for superior cleaning and sanitation.
Fill with water to the indicator line and insert in drilled stopper or bung to vent gases during fermentation. Includes body, piston, and vented cap.
This airlock is slightly shorter than the Standard S Shape Airlock.
Please note that your fermenter will need an airlock grommet or top hat grommet (sold separately).
Auto Syphon Racking Cane Easy Jiggler - 304 Stainless Steel - for syphoning out of a carboy, demijohn, bucket or FermZilla. This siphon includes 150cm x 10mm ID silicone tube.
This whole assembly is plasticiser and BPA free. It will not break like the plastic auto syphons or polycarbonate designs.
It's made robust out of 304 grade stainless steel and is really easy to take apart for cleaning. It's more versatile than a conventional racking cane and easier to start but at the same time similarly simple to use and clean.
Forget about fermenter taps and use a syphon. Threaded fermenter taps are hard to clean and sanitise so having a fermenter without a tap is often the best choice, and to get the beverage out of the fermenter without a tap this siphon is the natural choice.
INSTRUCTIONS
1: Sanitise and rinse your syphon
2: Make sure you have the full vessel significantly above the empty vessel you are filling
3: Attach the curved syphon to the hose
4: Submerge the end of syphon into your full container.
5: With long swift strokes, shake the syphon tube up and down to start the syphon action
Length: 57cm
Stainless tube: 14mm OD x 12mm ID
Silicone Tube: 1.5m x 10mm ID
From: Kegland
This easy to use and compact spunding valve is handy for keg transfers or pressurised fermentations when you want to limit oxygen exposure and use counter pressure in the keg you are filling into or in the fermenter you are using.
This new improved G2 model has several upgrades:
1. duotight fitting where the gauge attaches
- This allows for a multitude of different options such as digital gauge or larger gauge to be purchased separately and upgraded.
2. Manual ring pull pressure relief
- This allows for you to not only adjust the pressure with the black rotary knob but also use the ring pull to instantly release pressure if you want to release manually.
3. Option for Several Colour Coded PRVs to be used
Yellow - 1.2bar (17psi)
Red - 2.5bar (35psi)
Green - 4.5bar (65psi)
Grey - 7bar (100psi)
This is a low profile option only 4.5cm in height. This spunding valve fits to standard gas posts on your fermenter or keg.
It works right out of the box but has several upgrade options as shown in the images.
From: Kegland
The BlowTie Complete Kit (Diaphragm Spunding Valve), for pressure fermentation and pressure transfers.
Pressure Fermentations
With pressurised fermentation becoming ever more popular, it is important to have a method of regulating and controlling the residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.
Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg, it's often a good idea to have head pressure in the keg you are filling, especially if you are transferring a beverage that is already carbonated. For this reason, the BlowTie can consistently control this head pressure, giving you more consistent results and without losing carbonation in the process.
Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation. Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.
The BlowTie has been made differently, taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure. It can be easily disassembled for cleaning using a flat head screw driver.
This Kit Includes:
- 1 x Blow Tie Spunding Valve
- 1 x Duotight 8mm tee piece
- 1 x Duotight FFL to 8mm fitting
- 1 x 8mm Push in 0-40psi Gauge
- 1 x Ball Lock Disconnect (MFL) Grey/Gas
- 2 x NEW Black 8mm straight joiner pieces
Instructions:
Use the yellow adjustment knob to control the pressure coming out of the pressure vessel. Clockwise is higher pressure and anticlockwise is lower pressure. We recommend gassing a keg to a known pressure, e.g. 15psi, then attaching your Blow Tie Kit to the keg and adjust to 10psi.
Specs:
- Made from food grade acetal
- Stainless screws
- 8mm (5/16") push on both sides
- 0-40psi pressure rating
The unit can be easily disassembled for cleaning using a phillips head screw driver.
Features:
- 8mm push fit connectors
- precise pressure control
- easy to take apart and clean
- simple to adjust pressure
- made from high quality acetal
- diaphragm activated
- control pressure from 0-40psi
Pressure Fermentations
With pressurised fermentation becoming ever more popular it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.
Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg, it is often a good idea to have head pressure in the keg you are filling, especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process.
The BlowTie has been made different to traditional spunding valves by taking advantage of a diaphragm to actuate the sealing mechanism. This will release pressure from the pressure vessel with much more accurate control.
From: Kegland
A bored bung that tapers from 26mm across the top to 19mm across the bottom. Fits the Mangrove Jacks 25L Stainless Steel Fermenter.
A 2L borosilicate Erlenmeyer conical flask that is ideal for yeast starters using a stir plate such as the Wort Whipper..
Safety warnings:
**Please still exercise care when handling these and any other Borosilicate glass.**
There is a common misconception that Borosilicate glass is virtually bulletproof and can handle any dramatic temperature that is thrown at it. This is not strictly true.
Though it does have an incredible ability to withstand sudden and drastic temperature shocks compared to your average soda-lime glass, it should still be treated consciously with care.
Cool all glassware slowly to prevent breakage, unless you are using VYCOR glassware which can go from high heat to ice water with no damage.
Do not take your boiled flask directly from the stovetop straight into a bath of ice water. Though some people do this without failure, borosilicate glass is not designed for such an application. Please allow the flask to cool for a few minutes before running under water, before placing into an ice bath; the slower you introduce your flasks to temperature changes, the longer it will last. Going from fire to ice in a matter of seconds will introduce incredible amounts of stress to the glass structure. While the glass may be able to withstand this some of the time, other times you may not be so lucky. If the temperature differential is big enough, it will shatter. All Borosilicate glass will break eventually after a number of heat/cool cycles, it is impossible to give an exact number to determine when, but this is a natural an inherent feature of the material.
Please do not boil your flasks dry or dry them out using a stove. The temperature for drying should not exceed 140°C, which a naked flame can easily exceed.
Do not heat glassware that is etched, cracked, chipped, nicked, or scratched. It is more prone to break.
Do not heat glassware directly on electrical heating elements. Excessive stress will be induced in the glass, and this can result in breakage.
Small Bubbles that are less than 5mm and not located directly on the bottom of the flask is an acceptable manufacturing blemish as per our instruction from multiple manufacturers of glass.
A 2L borosilicate Erlenmeyer conical flask that is ideal for yeast starters using a stir plate such as the Wort Whipper..
Safety warnings:
**Please still exercise care when handling these and any other Borosilicate glass.**
There is a common misconception that Borosilicate glass is virtually bulletproof and can handle any dramatic temperature that is thrown at it. This is not strictly true.
Though it does have an incredible ability to withstand sudden and drastic temperature shocks compared to your average soda-lime glass, it should still be treated consciously with care.
Cool all glassware slowly to prevent breakage, unless you are using VYCOR glassware which can go from high heat to ice water with no damage.
Do not take your boiled flask directly from the stovetop straight into a bath of ice water. Though some people do this without failure, borosilicate glass is not designed for such an application. Please allow the flask to cool for a few minutes before running under water, before placing into an ice bath; the slower you introduce your flasks to temperature changes, the longer it will last. Going from fire to ice in a matter of seconds will introduce incredible amounts of stress to the glass structure. While the glass may be able to withstand this some of the time, other times you may not be so lucky. If the temperature differential is big enough, it will shatter. All Borosilicate glass will break eventually after a number of heat/cool cycles, it is impossible to give an exact number to determine when, but this is a natural an inherent feature of the material.
Please do not boil your flasks dry or dry them out using a stove. The temperature for drying should not exceed 140°C, which a naked flame can easily exceed.
Do not heat glassware that is etched, cracked, chipped, nicked, or scratched. It is more prone to break.
Do not heat glassware directly on electrical heating elements. Excessive stress will be induced in the glass, and this can result in breakage.
Small Bubbles that are less than 5mm and not located directly on the bottom of the flask is an acceptable manufacturing blemish as per our instruction from multiple manufacturers of glass.
The Bouncer Inline Beer Filter allows you to brew better tasting and clearer beer, with less waste, and without pumps or additives! Simply connect the filter between your fermenter and keg, or between your boil kettle and fermenter.
Perfect for up to 25 L batches.
Key features
-
improves the taste and clarity of your beer by filtering trub, krausen, hops, and proteins,
-
built to last, use it over and over, custom molded from high quality thermoplastic and T304 stainless steel in the USA, use up to 65℃,
-
easy to use and clean, gravity fed so no need to pressurise or pump, fewer parts to clean and sanitise, fits 3/8" inner diameter siphon tubing (standard size),
-
doubles as a mini-Randall, simply attach to a growler filler and add fresh flavours into the glass, try citrus peels for a lighter beer, or cracked coffee for a stout.
Specifications
Connectivity: 3/8″ hose barbs
Screen: 915 micron / 20 mesh
Filter Area: 4,974 square mm / 7.71 square inches
Max Operating temperature: 65C / 150F
Max Operating pressure: up to 150 psi at 21 C / 70 F
Replacement Gaskets for Bouncer Classic.
Similar to the Classic Bouncer Inline Beer Filter - but BIGGER. The Mac Daddy Bouncer has 224% more filter surface area, and three times the flow rate of the regular Bouncer.
Key features
-
the Bouncer's big brother, with more filter area and a higher flow rate - use on your big hoppy batches,
-
improves the taste and clarity of your beer by filtering trub, krausen, hops, and proteins,
-
built to last, use it over and over, custom molded from high quality nylon and T304 stainless steel in the USA, use up to 65℃,
-
easy to use and clean, gravity fed so no need to pressurise or pump, fewer parts to clean and sanitise, fits 3/8" inner diameter siphon tubing (standard size),
-
doubles as a mini-Randall, simply attach to a growler filler and add fresh flavours into the glass, try citrus peels for a lighter beer, or cracked coffee for a stout,
-
the Mac Daddy has 1/2" female pipe thread ports to adapt easily to standard 1/2” fittings. Use the included 3/8” or 1/2” hose barb adapters, or add your own quick-connect adapters to fit your set up. Use your Mac Daddy Bouncer out of the brew kettle, out of the fermenter, or out of your serving tap.
Specifications
Connectivity: 1/2″ NPT female, 1/2″ hose barbs, 3/8″ hose barbs
Screen: 915 micron / 20 mesh
Filter Area: 11,161 square mm / 17.3 square inches
Max Operating temperature: 65C / 150F
Max Operating pressure: up to 100 psi at 52 C / 125 F
It's the Bouncer Classic and Mac Daddy's big brother, the Bouncer Pro - a pro level inline beer filter. The Pro filters out dry hops, fruit, yeast, etc during transfers or kegging to produce better tasting and clearer beer. Multiple Pros can be easily used in series (coarse then fine screens) or parallel (for faster flow rates). Very easy to clean compared to frame and plate filters. Doubles as an infuser.
The Pro comes with a Red 20 mesh (915 micron), Blue 50 mesh (304 micron), and White 80 mesh (178 micron) screen, stainless steel tri-clamp adaptors, and a roll of pipe thread tape.
Key features
-
Pro level inline beer filter
-
Filters out dry hops, fruit, yeast, etc during transfers or kegging to produce better tasting and clearer beer
-
Multiple units can be easily used in series (coarse then fine screens) or parallel (for faster flow rates)
-
Very easy to clean compared to frame and plate filters
-
Doubles as an infuser
-
improves the taste and clarity of your beer by filtering trub, krausen, hops, and proteins,
-
doubles as a mini-Randall, simply attach to a growler filler and add fresh flavours into the glass, try citrus peels for a lighter beer, or cracked coffee for a stout,
Specifications
Connectivity: Stainless steel 1.5 inch tri-clamp and 1″ NPT female
Screens: Red 20 mesh (915 micron), Blue 50 mesh (304 micron), and White 80 mesh (178 micron)
Filter Area: 29.73 square inches (19,181 square mm)
Max operating pressure: up to 150 psi at 21 C / 70 F and 100 psi at 52 C / 125 F
Weight: 1 pound, 8 oz. / .69kg (with try-clamp adaptors and white screen)
Accessories included: Stainless steel tri-clamp adaptors, roll of pipe thread tape, three screens (see above)
Replacement filter screens for Classic Bouncer Inline Filter.
Contains:
- one blue 50-mesh screen
- one white 80-mesh screen
Replacement filter screens for Mac Daddy Bouncer Inline Filter.
Contains:
- one blue 50-mesh screen
- one white 80-mesh screen
Hose adapters for the Bouncer Filter Mac Daddy.
- Two 3/8″ hose barb adaptors
- Two 1/2″ hose barb adaptors
Take the work out of cleaning corny kegs, carboys and brewing vessels with the Bucket Blaster keg and fermenter cleaner. The Bucket Blaster is a great way to get your kegs, fermenters, fermzilla, carboy's or other brewery gear clean while you attend to other tasks.
Simply set up the keg washer basin with your cleaner or sanitiser, set a keg or carboy on over the jet nozzle, power up pump and let the keg washer do the work.
This unit comes with a 15L bucket which doubles as a storage container when you are not using the system. Some other keg washers come with a very small reservoir making it a pain to move, liquid spills over the sides easily and generally they just do not work as well. This unit has a large 15L bucket making it much less likely for you to spill liquid on your floor.
This system includes a 2000 litre per hour pump, the 15L bucket, a powerful jet nozzle, 3/8 EVABarrier tubing, a Duotight tee piece, a grey and a black ball lock disconnect and the stainless stand.
You can find instructions on how to assemble, operate, and maintain the bucket blaster here.
From: Kegland
This plastic carbonation cap has been designed to suit soda bottles, coke bottles, FermZilla lids and collection containers. These are great for cleaning your keg lines, or carbonating beer quickly in a bottle, or if you simply want to take beer to a mates.
Liquid and Gas ball lock compatible.
This carbonation cap is also suited to any of the FermZilla products such as the FermZilla Pressure kit.
Made from high quality engineering plastic, it will last a very long time. It is chemically resistant and also designed to resist impact and physical damage.
The thread specification on this product is the PCO 1881 (AKA Coke bottle thread).
Yellow Plastic Carbonation and Line Cleaning Cap or FermZilla Pressure Cap.
These carbonation caps are now available in yellow to help differentiate between gas and liquid posts. Liquid = Gold is all you need to remember. Add your silicone dip tube to this cap and never risk accidentally attaching your gas line. Note: It is a multi post, so it will take both gas or liquid if you want to change it up.
Need to clean your beer line? Carbonate your beer quickly? Or simply want to take a traveller over to a mates? Then do yourself a favour and grab one of these essential tools for your brewing needs.
Liquid and Gas ball lock compatible.
This carbonation cap is also suited to any of the FermZilla products such as the FermZilla Pressure kit.
This product is made from high quality engineering plastic and will last a very long time. It's chemically resistant and also designed ot resist impact and physical damage.
The thread specification on this product is the PCO 1881 (AKA Coke bottle thread).
From: Kegland
The Demijohn Handle makes it easier to move your full Demijohn/Carboy, reducing the risk of spillage.
It works with both the 23L Carboy and 11.5L Carboy.
The Easy-Siphon makes syphoning your beer or wine simple and is designed to start the flow in one stroke. The Easy-Siphon is made out of acrylic and includes a 60cm racking tube bent to perfection. It also includes an Anti-Sediment Tip.
The Tubing - 9.5mm ID fits snugly over the racking tube.
Compatible with the 5L Glass Jar Demijohn and 5L Glass Jar Demijohn with Screw Cap/Lid.
A smaller (shorter) 350ml syphon. Perfect to use with smaller fermenters.
The Tubing - 9.5mm ID fits snugly over the racking tube.
Compatible with the 5L Glass Jar Demijohn and 5L Glass Jar Demijohn with Screw Cap/Lid.
This black HDPE lid has been designed to be chemically resistant but also strong enough to hold up to 2.5bar pressure.
This lid can screw onto the top of your Fermzilla Collection Container and this allows you to use the Fermzilla collection container for other stainless fermenters with a 2 inch tri-clamp dump valve.
Note: clamp, seal, and container not included.
From: Kegland
FermZilla 27L Tri-Conical Starter Kit - Generation 3.2
Introducing the Gen3 FermZilla Tri-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and a 600mL collection container with a 3 Inch Tri-clover connection, the gold standard for sanitary design and effortless removal. No more complicated dump valve designs here, just simplicity. Brew with confidence on the new Tri-Clover FermZilla Range.
The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget. With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.
This is an incredible product at an extremely attractive price point in all the different sizes and models.
The FermZilla 27L Tri-Conical can be used in the following ways:
- Basic Gravity Fermenter - New Brewers
- Pressure Brewing Kit - Most Popular
- Hop Bong Pressure Kit - For Intermediate Brewers
- Glycol Twister Pressure Brewing Kit - Glycol Obsessed
What's new the difference between Gen2 and Gen3?
1. Moulded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch tri-clamp butterfly valve
3. 3 Inch tri-clamp 600mL collection container
Is it easier to clean / take apart than the Gen2?
YES, It is by far the easiest Conical PET fermenter to disassemble and clean into all the nooks and crannies. Simply release all pressure inside the vessel and detatch the tri clover clamps.
What does the starter kit come with?
1 x 27L Conical FermZilla Tri-Conical Base Kit (unassembled)
1 x 27L Gen3 Tri-Conical Tank with metal neck ring
1 x Standard Top Lid, with Red PRV (35psi) [2 x Male PCO1881 Cap Threads] [Up to 4 drill ports for accessories]
1 x Collar Lid Ring
1 x Grommet PCO1881 Black Cap + 1 x Blank PCO1881 Black Cap for lid
1 x Premium 3 Piece Airlock
1 x 3 inch tri-clamp to 3 inch tri-clamp butterfly valve
1 x 600mL Collection Container & Lid* [2 x Male Cap Threads]
2 x Blank PCO1881 Black Cap
1 x 3 piece ~ 3 inch tri clover clamp [+ 1 x 3" Beaded Silicone Seal]
1 x 2 piece ~ 2 inch tri clover clamp [+ 1 x 2" Beaded Silicone Seal]
1 x Stainless Stand with swing handles
1 x Stainless Steel Handle Assembly
1 x Strip Stick On Thermometer
1 x Level indicator sticker (Litres and Gallons)
1 x Spare Lid O-Ring
1 x Spare Collection Container O-Ring
Instructions:
To download the instruction sheet for this product click on the link below:
FermZilla 27L - Tri-Conical PDF Instruction Manual
Dimensions:
To download the dimensioned drawings for this product click on the link below:
FermZilla 27L Tri-Conical Dimensioned Drawing
Warnings:
Please read the instructions thoroughly before use.
- We will not be held liable for misuse or mishandling of the unit contrary to the instructions.
- Keeping the units out of direct sunlight is a must for all PET fermenters. Sunlight degrades PET.
- Do not expose to temperatures exceeding 35°C and pressure ferment past 5psi at these temperatures.
Please note:
When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage.
Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.
Help Stabilize Your Fermentation Temperatures with the FermZilla Insulating Jacket
Fits both FermZilla 27L Conical and All Rounder 60L
Give your fermenter practical temperature support! Kegland’s insulating jacket easily zips over your 27L Conical or 60L All Rounder, creating a protective thermal layer to reduce ambient temperature swings. Use it standalone or supercharge your control with these active solutions:
How It Works:
Reduces Temperature Fluctuations: Minimises impact from room temperature changes
Active Heating: Pair with a RAPT Temperature Controller + Heating Wrap
Active Cooling: Use with Temp Twister Coil + Pump Kit
Passive Cooling: Place frozen water bottles between jacket and fermenter
Full Coverage Design: Light-blocking insulation with lid access
Compatibility:
→ FermZilla 27L Conical (Gen 3)
→ All Rounder 60L
Your Complete Thermal System:
Maximize control with these setups:
→ Basic: Jacket alone (reduces fluctuations)
→ Pro Heating: Jacket + RAPT Controller + Heating Wrap
→ Pro Cooling: Jacket + Temp Twister Coil + Pump Kit
→ DIY Cooling: Jacket + frozen bottles
Complete Your Temperature Control Kit:
Heating Solutions:
Cooling Solutions:
This collection container fits all the FermZilla Tri-Conical fermenters that have a 3 inch x 3 inch butterfly valve. No more threads or removal tools to get this off, simply depressurise and remove the tri-clamp fitting. We'd recommend placing a towel or upside down frisby to catch some drips.
The clear body is made from Tritan from Eastman Plastics. This heat tolerant plastic is BPA, and plasticiser free.
The ports on the side of this collection container are the same as a standard coke bottle or soft drink bottle. These are also the same on the top of the FermZilla.
We would recommend using the following two items (not included) on your collection container for the average user:
1 x Red Ball Lock Plastic Carbonation Cap x 6.35mm duotight
1 x PCO1881 Gas Pressure Relief Valve Cap (PRV) and Pressure Relief Valve 35PSI (Red)
Includes:
1 x 600mL Tritan plastic collection container with 3" tri-clamp ferrule and 2 x Vertical PCO1881 Carbonation Cap Ports
1 x 3" tri-clamp clamp (3-Piece)
1 x 3" tri-clamp beaded seal
1 x 3" tri-clamp black POK end cap
Dimensions:
170mm High
Tapered from 3 Inch tri-clamp down to 66mm
From: Kegland
FermZilla 55L Tri-Conical Starter Kit - Generation 3.0
Introducing the Gen3 FermZilla Tri-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and redesigned tri-clover dump valve. This unit was born from customer feedback we received on the Gen2 Model. No more complicated dump valve designs here, just simplicity. Brew with confidence on the new Tri-Clamp FermZilla Range.
The new FermZilla is a revolution in home brewing allowing home brewers and small micro-breweries a level of control that meets everyone's budget. With the FermZilla you have many of the benefits of a much more expensive stainless conical fermenter but with the additional benefit of being able to see the fermentation process in action and also ferment at pressures up to 2.4bar.
This is an incredible product at an extremely attractive price point in all the different sizes and models.
The FermZilla 55L Tri-Conical can be used in the following ways:
- Basic Gravity Fermenter - New Brewers
- Pressure Brewing Kit - Most Popular
- Hop Bong Pressure Kit - For Intermediate Brewers
- Glycol Twister Pressure Brewing Kit - Glycol Obsessed
What's new the difference between Gen2 and Gen3?
1. Molded 3 inch tri-clamp ferrule in the body of the FermZilla tank
2. 3 inch to 2 inch tri-clamp Butterfly Valve
3. 2 inch tri-clamp compatible Collection Container
Is it easier to clean / take apart than the Gen2?
YES, It is by far the easiest Conical PET fermenter to disassemble and clean into all the nooks and crannies. Simply release all pressure inside the vessel and detatch the tri clover clamps.
What does the starter kit come with?
1 x 55L Conical FermZilla Tri-Conical Base Kit (unassembled)
1 x 55L Gen 3 Tri-Conical Tank with metal neck ring
1 x Standard Top Lid, with Red PRV (35psi) [2 x Male PCO1881 Cap Threads] [Up to 4 drill ports for accessories]
1 x Collar Lid Ring
1 x Grommet PCO1881 Black Cap + 1 x Blank PCO1881 Black Cap for lid
1 x Premium 3 Piece Airlock
1 x 3 inch tri clover to 2 inch tri clover Butterfly Valve
1 x 1000mL Collection Container & Lid* [2 x Male Cap Threads]
2 x Blank PCO1881 Black Cap
1 x Brewbuilt Flex Container lid with 2 inch tri-clover ferrule.
1 x 3 piece ~ 3 inch tri clover clamp [+ 1 x 3" Beaded Silicone Seal]
1 x 2 piece ~ 2 inch tri clover clamp [+ 1 x 2" Beaded Silicone Seal]
1 x Stainless Stand with swing handles
1 x Stainless Steel Handle Assembly
1 x Strip Stick On Thermometer
1 x Level indicator sticker (Litres and Gallons)
1 x Spare Lid O-Ring
1 x Spare Collection Container O-Ring
Instructions:
To download the instruction sheet for this product click on the link below:
FermZilla 55L - Tri-Conical PDF Instruction Manual
Dimensions:
To download the dimensioned drawings for this product click on the link below:
FermZilla 55L Tri-Conical Dimensioned Drawing
Warnings:
Please read the instructions thoroughly before use.
- The current version can be found in the 'instructions' tab above. We will not be held liable for misuse or mishandling of the unit contrary to the instructions.
- Keeping the units out of direct sunlight is a must for all PET fermenters. Sunlight degrades PET.
- Do not expose to temperatures exceeding 35°C and pressure ferment past 5psi at these temperatures.
Please note:
When using this vessel under pressure. You must perform a water pressure check to ensure your connections are leak proof before you fill the fermenter every time. To do this. Fill your FermZilla up with some water, then apply a minimum of 15psi pressure to the vessel. Check for leaks around all Cap / Threads by tipping it upside down, in all directions where there are risks of leakage.
Occasionally these units may come with some small indentations/dimples/dents from shipping, this is just a reality of shipping large blow-moulded thin-walled vessels. But don't panic, these fermenters are designed to endure minor deformations such as this. This was a necessary implementation into the design so that they can withstand some accidental suction from cold crashing and rough handling in transit without compromising their integrity and ability to endure high pressures. All small dents will push out and settle with use and positive pressure and are only an issue and warrant replacement in the rare event they start to show white stress patterns or have damaged the plastic.
From: Kegland
