Sort by:
Silicone Stopper / Bung for Ss Brew Buckets made from food grade silicone.
The Smell Eliminator Kit completely eliminates ALL smells from the fermentation process for both beer and spirits.
Includes everything you need to attach to a standard fermenter with airlock (airlock not included).
Now you can ferment wherever is best to maintain your desired fermentation temperature without worrying about the smell.
The carbon cartridge for the Smell Eliminator Kit is made from a specially designed dense carbon block, which will last for approximately 5 brews or washes. Will not filter liquids.
Made from 304 stainless for hygiene and will last a lifetime.
Instructions: The Smell Eliminator Kit
A replacement carbon cartridge for the Smell Eliminator Kit. Made from a specially designed dense carbon block, it will last for 5 brews or washes. Will not filter liquids.
Introducing the all new Brew Bucket 2.0
Nearly a decade after the Brew Bucket was first produced, Ss Brewtech challenged the Ss Engineering Team to pair some of the newest technologies with the original design.
For use on Brew Bucket 3/8" Ball Valve. Includes:
- 4 pcs 8.5 mm x 1 mm Buna N 70 O-rings
- 2 pcs 16mm x 1.8 mm Buna N 90 O-rings
- 6 pcs total in this set (enough to replace all o-rings on one Brew Bucket valve)
Replacement Lid Seal for SS Brewtech Brew Buckets and Chronicals; made from brewer's grade silicone.
These also fit the FTSs lids at the matching size.
From: Ss Brewing Technologies
Colour liquid crystal thermometer to place on to your fermenter. Has a range of 10℃ - 36℃ going up in 2℃ increments.
Screw-in tap for use with Handcraft Supplies 30L Wide Mouth Fermenter. Simply screw the tap in the pre-drilled hole at the bottom of the fermenter before filling the fermenter with your ingredients. Mangrove Jack's Silicone Hose 100mm is required to connect the tap to a brew bottler. Not compatible with sediment reducer.
Temp Twister Pump Kit with Return Line and Clamp.
If a glycol chiller is a bit out of reach at the moment, but you want to use the Temp Twister in your Kegmenter or FermZilla, this little product can help you on your way to cool your fermenter. Simply submerge the pump in a large bucket with water and ice.
The more insulation you give your fermenter and keep it at a relatively stable temperature the better. We suggest using this in conjunction with a temperature controller.
Parts List:
1 x 1.2m Length of Insulated 6mm x 9mm EVABarrier Hose
1 x 1.2m Length of 6mm x 9.5mm hose (return line back to the bucket) (colour may vary)
2 x 9.5mm duotight Elbows (For temp twister)
1 x Temp Twister 12v Pump and power supply
From: Kegland
A stainless steel, 1/2" thread, weldless thermowell (takes any probe up to 7mm ID).
This thermowell works great with any kegmenter, keggle, brew pot, boiler and various other brewery hardware to get an accurate core temperature of your vessles.
This thermowell has a 7mm bore, so it's ideally suited to any probe type up to 7mm. Most probes are 6.5mm or smaller in diameter meaning they will fit nicely into this well. It's ideal for the RAPT Temperature controllers.
This is a weld free design so all you need to do is drill a 20mm hole and file this out a fraction and this will go right into the hole with no welding required. The threads have been designed to be sanitary so you just screw it against your vessel wall and none of the threads will be exposed to liquid. The soft silicon seals will seal against curved surfaces of your pots and other vessels.
If you want to make a really smooth hole easily in your vessel walls we recommend the use of a step drill bit and 20mm hole punch.
Length: approx. 100mm
From: Kegland
- Brewer's Grade 304 Ss
- Installs into 17mm punched / drilled hole
- 6.5 mm inner diameter of tube opening
Usually available in these sizes:
- 100mm
- 200mm
- 300mm
Includes one o-ring.
From: Ss Brewing Technologies, USA
A 1.5" tri-clamp thermowell fitting from Krome Dispense that is approx. 15cm long.
- 304 Stainless Steel
- Approx. 15cm thermowell
Does not include tri-clamp clamp or gasket.
From: Krome Dispense
This thermowell fits into any 8mm Hole and can literally be installed into almost any fermenter lid.
Having the thermowell attach to the lid of a fermenter is ideal as it means the penetration through the fermenter body is at the top of the fermenter not below the liquid line. This makes the whole process more sanitary and reduces the number of difficult parts to clean.
This thermowell can be pushed through a bung with a 6-8mm hole but it also includes the Duotight bulkhead fitting that you can use to attach this thermowell to the lid of your FermZilla Fermenter.
It goes right into the middle of the core of your vessel meaning you get an accurate core reading of the liquid in the tank/vessel.
Note: If you need to shorten the length of this thermowell tube then simply use a tube cutter to the desired length.
Made from: 304 stainless steel
Dimensions: 8mm OD x 7mm ID
From: Kegland
Tri-Clamp Cap to Ball Lock Post fitting, with both liquid and gas post options. These 1.5" tri-clamp fittings provide a sanitary and leak-proof connection, and can be used with our ball lock connectors. The price is per single unit - gas or liquid - not for pair like in the photos.
From: Krome Dispense
Material: Stainless 304
The Wort Whipper - Super Compact Adjustable Magnetic Stirrer Machine.
Now even more compact than ever! Measuring at just 28mm high and 120mm wide this little sucker can punch a huge amount of power through to your stir bar.
Recommended Power = Low (just enough to suspend the yeast, not a super vortex).
Dial up from off with the bar in the middle of your Erlenmeyer Flask until you just start to see a small vortex forming at the top, then dial a bit off that. You don't need a crazy amount of vortex to make a good starter. You just need to keep the yeast suspended.
If you're new to brewing you'll soon learn that healthy yeast makes better beer. The best place to start with making healthy yeast is to build up their numbers. Use an online calculator to find out how much yeast you need to build up to get the best possible beer fermented. Use either a 2000mL or a 5000mL Conical Erlenmeyer flask. You'll be able to make a varying range of yeast starters depending on your batch size.
Includes:
- Magnetic Stir Bar
- 1m 12v Plug Adaptor
Note: Erlenmeyer Flask in photo is not included.
From: Kegland
