Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread.

It is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. 

These push in fittings are suitable to be used up to 100 psi.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

Note: colour may vary.

From: Kegland

Duotight - 9.5mm (3/8”) Female x 1/2 Male Thread Bulkhead (suits TempTwister).

Looking for high quaility push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Why use Double O-rings?
The secret to the Duotight sealing performance is not just the fact that it uses high quality EPDM o-rings but also use two of them.  The double o-ring means it literally has twice the sealing surface surface when compared with other push in fittings.  This makes these fittings even more reliable and reduces the chance of a leak significantly.

The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market.

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi

Includes Locking Nut (suitable for the TempTwister).
This fitting is ideally used with the TempTwister for a FermZilla or KegMenter for use in the FermZilla Range, Kegmenter range or even drilled into an HDPE fermenter.

What is EPDM?
EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, a wide variety of alkaline and acid compounds, water, alcohol, ketone, and beverages.

EPDM is also resistant to aging, and weather and will not perish easily like other rubber compounds.   When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long-lasting food grade applications.

From: Kegland

Duotight - 9.5mm (3/8") Check Valve (Gas).

This elbow piece is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

Due to the fact that this check valve cannot be taken apart to clean, we do not recommend it to be used with liquid.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. 

These push in fittings are suitable to be used up to 100 psi.

Compared to other push in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

From: Kegland

The BlowTie Diaphram Spunding Valve - a great tool if you want to control the pressure retained in a pressure vessel that is releasing pressure. It has been designed for simplicity and ease of putting together. Many brewers use this spunding valve in combination with the FermZilla pressure rated fermenters.

This is the new "BlowTie 2" upgarded model which has the integrated pressure gauge. The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure. This BlowTie unit can be easily disassembled for cleaning using a screw driver. Designed to suit 8mm (5/16") tubing. It's compatible with both the 4mm ID Tubing or 5mm ID.

This compact solution for adjusting residual pressure in your fermenter makes pressure control easier than it's ever been. This can be used for compressed air, CO2, nitrogen, mains water supply and many other things but its primary use is to control the residual pressure inside fermenters.

Specifications:
1. Suits pressures 0-23psi (but with different gauges the unit can go above 100psi)
2. Made from food grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides

The design utilises the reliability of the Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.

Pressure Fermentations
With the popularity of pressurised fermentation it has become increasingly important to have a method of regulating and controlling this residual pressure from the fermentation process. The BlowTie has been designed specifically for this reason.

Pressure Transfers
When transferring from keg to keg, keg to bottle, or fermenter to keg it is often a good idea to have head pressure in the keg you are filling into especially if you are transferring a beverage that is carbonated. For this reason the BlowTie can consistently control this head pressure giving you more consistent results and without losing carbonation in the process.

Traditional spunding valves that use a simple spring against a seal are flawed right from the beginning as the physical aspects of the design dictate that you will have a significant difference between the opening pressure and closing pressure during operation. Brewers have tolerated this imperfection for long enough and now you can control these pressures far more accurately.

The BlowTie has been made completely differently taking advantage of a diaphragm to actuate the sealing mechanism that will release pressure from the pressure vessel with much more accurate control pressure.

Instructions:
Use the yellow adjustment knob to control the pressure coming out of the pressure vessel. Clockwise is higher pressure and anticlockwise is lower pressure. We would recommend gassing a keg to a known pressure e.g. 15psi then attach your BlowTie Kit to the keg and adjust to 10psi.

These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.

IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)

Material: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland

The Duotight Inline Regulator - these compact inline regulators have been designed to suit 8mm (5/16") tubing.

Suits pressures 0-150psi however this unit is packed with the 0-60psi gauge as standard. Suitable for mains water pressure, also suitable for liquid or gas.

- Made from Acetal/POM, EPDM o-rings and stainless teeth
- Suits 8mm (5/16) OD tubing
- Includes integrated 0-60psi Pressure Gauge

For higher pressures such as mains water supply we recommend the 4mm ID Tubing, or 5mm ID if you do not need as high pressures and you would prefer higher flow rate.

This compact solution for adjusting water and gas pressure can be useful in many different applications. It can be used for compressed air, CO2, nitrogen, mains water supply and many other things.

The design utilises the reliability of the Kegland patented Duotight o-ring system to make sure you can fit hoses to this unit quickly and with leak free connections.

These gauges are accurate to about 10% of the range of the pressure gauge. So if you use the lowest range possible it will ensure the best possible accuracy.

IMPORTANT WARNING: Do not exceed gauge pressure. If you set a gauge pressure higher than the graduations on the gauge you can damage the gauge. (ie if you are using the 0-60psi gauge. Do not set pressure above 60psi or damage to the gauge may occur.)

Made From: food grade engineering plastic, stainless steel and quality made EPDM seals
From: Kegland

Duotight push in fitting for 8mm line to 5/8inch thread - ideal for keg couplers and tap shanks.

Duotight fittings feature a double o-ring sealing design for a more secure seal. The seals are not only high quality EPDM o-rings but also it has two of them. The double o-ring means there is literally twice the sealing surface when compared with other push in fittings. This makes Duotight fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that you can bend the hose with a much tighter radius without leaking issues. 

We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used for up to 100 psi.

Duotight 8mm (5/16) one way check valve/non-return valve.

This very handy fitting could save your regulator and is a good investment. This particular type of check valve has low opening pressure of only 1 psi. It is suitable for clean liquids such as water or for gas. The spring and internal components are made with stainless steel and quality EPDM seals.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. 

Fits 8mm outer diameter tube. 

Note: colour may vary.

From: Kegland

This Duotight Push-Fit Elbow - 8mm x 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.

Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.

Fits 8mm outer diameter tube.

From: Kegland

This Duotight Push-Fit Tee - 8mm - will allow you to join beer or gas line sections on your kegging system. Simple to use and requires no tools.

Duotight push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

These push in fittings are suitable to be used up to 100 psi. They are extremely easy to use and allow you to simply push your beer and gas line straight into these fittings. No need to purchase clamps. To remove the fitting simply push in the collet and the hose can be removed. We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal.

Fits 8mm outer diameter tube.

Note: colour may vary.

From: Kegland

Duotight - 8mm x 1/4 inch BSP Male.

No clamps necessary, however we do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed.

These push in fittings are suitable to be used up to 100 psi.

These push in fittings have been engineered for maximised performance in both gas and liquid applications. Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port.

From: Kegland

This manifold splits one line into two, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This manifold splits one line into four, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This manifold splits one line into six, each with a check valve. The check valve can also be removed if you want gas or water to move freely in both directions.

If you want to cap off certain lines, we would recommend using the Duotight - 8mm (5/16') Plug 

Using a thin flat headed screw driver, simply slide/pop the black retainer tabs and remove the ball valve.

The Duotight 8mm 2-way manifold is ready with mounting capabilities out of the box using button head screws. But if you're going to mount it on a kegerator, we would suggest using the Duotight 8mm adhesive brackets (no drilling required).

Not suitable for liquids other than filtered water.

Looking for high quality push in fittings that will seal tight?  Duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design.

Compatible with:
EVABarrier 4mm ID x 8mm OD line
EVABarrier 5mm ID x 8mm OD line
Red EVABarrier 5mm ID x 8mm OD line
Black Lightshield EVABarrier 4mm ID x 8mm OD line
Not compatible with 6.3mm ID x 9.5mm OD line

No clamps necessary! 
We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

These push-in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push-in fittings on the market, Duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push-ins on the market have EPDM o-rings, let alone two! per push-in connection.

From: Kegland

This rigid 50mm long joiner is made from strong polypropylene. It's useful to make rigid joins with push in fittings that are dead straight. Although it's possible to make joins using short pieces of 8mm OD Evabarrier 5mm Beer Line this is far more flexible and when mounting parts to a gas board or wall its will often make things much neater if you use these instead.

The 50mm length is long enough so even after pushing right into two duotight 8mm fittings on both ends you should still have a exposed length of about 3mm so you can still relatively easily take the fittings apart later.

From: Kegland
Dimensions: 8mm OD x 6mm ID x 50mm long

This really handy device is great for filling kegs, keg to keg transfers or fermenter to keg transfers.

Fantastic for use with Fermentasaurus or other pressurisable fermenters.

Simply attach this device to the output gas post of your Keg then when the keg is full it will prevent further liquid exiting the gas post. This means you can literally set and forget and fill kegs automatically without the risk of kegs overflowing all over the floor.

For even better results we recommend this product to be used with the Duotight - BlowTie Diaphram Spunding Valve - Adjustable PRV.  This blowtie spunding valve will also enable to to apply head pressure to the keg meaning you can control the flow speed but also reduce the foam generated in the filling process particularly for carbonated beverages like beer.

This flow stopper includes:

• 2 x duotight 8mm x 5/8 push in fittings
• 1 x ball float
• 1 x stainless spring
• 2 x straight 8mm joiners
• 1 x acrylic sight glass (with 5/8 male thread on either side)

Made exclusively for the Duotight manifolds and Gen 3.0 Duotight 8mm fittings to be mounted to a flat surface.

These can swivel around if you need to mount on a particular angle once stuck down.
They can also easily be removed from the 8mm Duotight side as they simply click/clamp in to each other.

If you are to mount this inside your Kegerator / Keezer, you must do so when the unit is off / warm. It will not stick as well in a moist / cold environment. Best to give it at least 24 hours of stick time before attaching weight / hosing to it.

Wipe down surface with isopropyl alcohol prior to sticking.

Most commonly to be used with:

• 8mm (5/16) duotight x 6 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 4 Way Manifold with Check Valves & Isolation Valves
• 8mm (5/16) duotight x 2 Way Manifold with Check Valves & Isolation Valves
• and duotight - 8mm (5/16) x 5 Way Multi-Tee

If you want to know if your Duotight fitting will fit this, it must be a grey Duotight that has a black collet piece.

Not suitable for 8mm ball lock disconnects
Not suitable for multiple re-applications

From: Kegland

The queen of English hops with a pedigree dating back to 1790, East Kent Golding is to British brewers what Hallertau Mittelfrüh is to their German colleagues. A premium appellation, East Kent Goldings hops can only come from Kent.

East Kent Goldings has been described as flowery, earthy, spicy, with honey notes and citrus peel or citrus candy overtones and an herbaceous, spring meadow-like undercurrent. Gentle and refined, dry hopping can bring forth its citrus aspects alongside a fresh grassy note.

Regarded for centuries as England’s finest hop, EKG has been a spotlight flavour in the profiles of hoppy ales from the British Isles: IPA, pale ale, and bitter. It’s used at lower rates to subtle affect in Scottish and other darker, maltier ales.

The Easy-Siphon makes syphoning your beer or wine simple and is designed to start the flow in one stroke. The Easy-Siphon is made out of acrylic and includes a 60cm racking tube bent to perfection. It also includes an Anti-Sediment Tip.

The Tubing - 9.5mm ID fits snugly over the racking tube.

Compatible with the 5L Glass Jar Demijohn and 5L Glass Jar Demijohn with Screw Cap/Lid.

The Easy Siphon Clip holds your Easy Siphons to Carboys, Buckets and more! Made from lasting plastic materials, so you can clip and unclip your Easy Siphons without issues.

Works with:

• Easy Siphon 3/8"
  
• Easy Syphon Mini - 350mm
  
• Legacy Easy Siphon 3/8"

Please note: if the clip is used with the Legacy Easy Siphons (pre-2022 models), it will not work with the new models afterwards as the clamps will stretch to adapt to the bigger diameter of the older models.

A smaller (shorter) 350ml syphon. Perfect to use with smaller fermenters.

The Tubing - 9.5mm ID fits snugly over the racking tube.

Compatible with the 5L Glass Jar Demijohn and 5L Glass Jar Demijohn with Screw Cap/Lid.

Strong black aniseed with dark overtones of a liquorice character.

With 1.15 litres of Vodka or alcohol base (38%)
Add 50 ml of Edwards Essences
Add 320 grams of sugar
Shake Well !
Makes 1.4 litres

Product should only be used in accordance with instructions

A traditional rich Brandy with a smooth mature style to excite the palate.

Mixing Instructions:

With 700 ml of Vodka or alcohol base (38%)
Add 10 ml (2 caps) of Edwards Essences
Shake Well !
Makes 710 ml

Product should only be used in accordance with instructions

Try Edwards Essences Brandy if you like:

Luxuriously indulgent, rich butterscotch with a hint of roasted toffee. Works exceptionally well in both schnapps or cream liqueur, “Toffee Cream”.

With 850 ml of Vodka or alcohol base (38%)
Add 50 ml of Edwards Essences
Add 350 grams of white sugar
Plus add 260 ml of water
Shake Well !
Makes 1.4 litres

Product should only be used in accordance with instructions

Rich spices expertly blended with Caribbean Rum promises to deliver a swashbuckling adventure that’ll sail across your tongue leaving your tastebuds tingling in paradise.

With 700 ml of Vodka or alcohol base (38%)
Add 10 ml (2 caps) of Edwards Essences
Shake Well !
Makes 710 ml

Product should only be used in accordance with instructions

Try Edwards Essences Captain Jack Spicy Rum if you like:

Product should only be used in accordance with instructions

This 50ml essence flavours 1.4L

A black raspberry flavoured liqueur perfect as an aperitif or mixed with prosecco, champagne or white wine.

With 850 ml of Vodka or alcohol base (38%)
Add 50 ml of Edwards Essences
Add 250 grams of Brown sugar (more or less to taste)
Water to make 1.4 litres
Shake Well !

Product should only be used in accordance with instructions

Fresh tropical coconut laced with the finest Jamaican Rum flavour, will give you a taste of paradise. Also works exceptionally well in a cream base.

With 850 ml of Vodka or alcohol base (38%)
Add 50 ml of Edwards Essences
Add 350 grams of white sugar
Plus add 260 ml of water
Shake Well !
Makes 1.4 litres

Product should only be used in accordance with instructions

Double Up on flavour where smooth Irish whiskey meets golden honeycomb in a delightfully mischievous blend. Each sip unveils layers of buttery honeycomb melting into caramelised sugar notes, while the whiskey's subtle vanilla undertones provide a sophisticated backbone. Perfect neat, on the rocks, or as the secret weapon in your favorite cocktail, Double Up proves that good things come to those who play with tradition

Makes 1.25 litres

Product should only be used in accordance with instructions

Tasting of rich dark espresso beans, with hints of cream and vanilla extract to create a wonderfully sweet, decadent velvet finish.

Product should only be used in accordance with instructions

A classic dry Gin with a fresh clean taste of Juniper and citrus neatly rounded with angelica and coriander spices. Mix with tonic water and a slice of lemon and sink into bliss.

With 700 ml of Vodka or alcohol base (38%)
Add 10 ml (2 caps) of Edwards Essences
Shake Well !
Makes 710 ml

Product should only be used in accordance with instructions

A great all round Whisky with both malt and Smokey characters. Excellent over ice or blends very well with your favourite mixer.

A wonderful smooth flavoured bourbon with the rich character of a single strain honey. Perfect on the rocks, and a great addition to many premium cocktails. If required a little sugar can be added to enhance the richness of the honey character.

With 700 ml of Vodka or alcohol base (38%)
Add 10 ml (2 caps) of Edwards Essences
Shake Well !
Makes 710 ml

Product should only be used in accordance with instructions

Try Edwards Essences Honey Bourbon if you like: