Campden Tablets for use in winemaking to sanitise fruit must or to preserve wines/ciders. Simply crush and dose as per instructions on label.

Can also be used to remove chlorine and chloramine from brewing water.

Approximately 50 tablets in a tamper proof and resealable tub. 

Contains sodium metabisulphite.

Caution: Gives off toxic gas. Avoid vapours and contact with sensitive skin.

A brewing heater belt that fits around your fermenter to provide steady and constant warmth for your brew. The 30 watts will gently warm without creating a hot spot, and can be moved up or down the fermenter to increase or decrease the heat transfer to the brew.

To further control the temperature of your fermentation, combine with a RAPT Temperature Controller or similar to regulate the heater belt automatically.

Note: fermenter not included.

From: Kegland

These 304 Stainless 2200w weldless elements are designed to fit a 32mm hole inside the wall of your brewing vessel or boiler. It comes bundled with the power cord.

We do recommend using a RAPT Temperature Controller to run this element with the appropriate thermowell or temperature probe attachment.

These electric brewing elements are highly recommended for your HLT, or even for a HERMS or RIMS setup. Multiple elements may be required for larger volumes and depending on what temperature you are trying to achieve. If you are going to be using these elements directly in your mash tun, and will try to maintain temperature using the element, we would recommend getting a power control chip 3600w to modify the power output to the element. Too higher power directly in contact with your malted grain can cause scorching/off flavours as the temperature may not be evenly distributed and isolated purely around the element itself.

Element Length: approx. 300mm
Diameter: approx. 25mm
Thread: approx. 32mm
From: Kegland

3600 Watt Stainless Steel Heating Element with 2 inch tri-clamp (220-240v)

It can be fitted to a 2" tri-clamp ferrule. It does have a water-resistant screw element guard. This was produced to be used with the 118L Kegmenter that has 2" ferrules.

It is highly regarded as a popular and reliable element for distillers and homebrewers.

This element is to be installed by a professional electrician with a 15amp Cord. 

From: Kegland

Fermentation Heating Wrap Belt - With Velcro Strap (30watts) 220-240VAC (50-60hz)

Perfect heating solution for those who want more even coverage and absolute certainty that their PET fermenter will not melt even if the fermenter is empty.

Punching in at an ample 30 watts, this heating wrap belt is great when paired with insulation and a temperature controller box to dial in that optimum fermentation profile.

To further control the temperature of your fermentation, combine with a RAPT Temperature Controller or similar to regulate the Heating Wrap Belt automatically.

Features:

• Easy to use
• Handy velcro strap
• Low watt density
• Durable vinyl coating
• 30 watt gentle heating
• Great for fermenters or bottle conditioning
• Sit on top or wrap around your fermentation vessel

Dimensions: approx. 1000mm x 250mm

From: Kegland

Heavy Duty Vulcanized Latex Brewing Gloves - 55cm Long.

These heavy duty brewing gloves are made from vulcanized latex, ideal for cleaning around the brewery or even the home. Seriously long for getting those arms deep into Kegmenters, Fermzillas and those brew pots.

Tough chemical resistant material provides good protection to your hands during clean-up and sanitary handling of equipment. They are 55cm long so will also protect the forearm when reaching into harsh cleaning chemicals.

Weight: approx. 300gm
From: Kegland

The Heat Resistant Gloves / HIZO Oven Mitts are as impressive as they are functional with the ability to handle contact with temperatures of up to 500° Celsius (932°F). This means that it is perfect for use with oven baking, hot pots, grilling, barbecuing, and woodstoves.

Fashioned with high-quality aramid fibers which work to insulate and protect hands from burning temperatures, these gloves have a comfortable cotton and polyester lining which allows for breathability to resist sweating and a gauntlet-length style of design to protect wrists and forearm from scorching heat as well. These gloves are thick to provide excellent thermal protection and durability, but they are lightweight for extended use without fatigue.

Sizing: Medium only

With heat resistance up to 500°C, these gloves are perfect for:

• Perfect for oven baking, hot pots, grilling, barbecuing, and woodstoves
• Adjusting logs in the fireplace
• Touching scorching hot utensils or food while boiling or frying
• Changing light bulbs

Features:

• High-quality aramid fibers for insulation and cotton and polyester lining
• Designed for mobility and flexibility in mind
• Food-grade silicone layer
• Machine-washable, and can be easily hung on the line to dry

From: Kegland

30mm Hoffman Clamp - Stainless Steel.

Hoffman Clamps are used to control the flow in flexible tubing. The clamps have a machined adjustment screw to permit accurate regulation of the flow.

Screw Compressor Clamps are used to control the flow in flexible tubing. The clamps have a machined adjustment screw to permit accurate regulation of the flow. All corners are rounded to prevent cutting of the tubing.

This can be particularly useful when using a liquid management still.

Size: 30mm
From: Kegland

A hole plug fitting for plugging 17mm holes.

- 304 Stainless Steel
- Includes o-ring for leak-proof seal
- Includes spare o-ring

Ideal for plugging holes from these fittings:
- Brew Bucket ball valve
- Bucket / Chronical thermowell
- Brewmaster Edition Chronical FTSs chiller coil holes
- FTSs lid holes

From: Ss Brewtech

2" Tri-Clamp Sight Glass - Hop Bong with PCO1881 Male Port and black bottle cap.

Named purely on its looks and not its function. The Hop Bong is a versatile pressurisable tri-clamp accessory, capable of not only dry hopping oxygen purged hops into fermenters, but also as an inline carbonation/oxygenation accessory.

This particular sized tri-clamp hop bong was designed for the FermZilla Tri-Conical and All Rounder fermenters with the new tri-clamp adapted pressure lid. It can also be adapted to any 2" tri-clamp port in your system to use either inline or as a dry hopping device.

Constructed from Nylon 12: An autoclavable, extremely robust, and chemical resistant engineering plastic.

Depending on how you set up your Hop Bong, the most common two fittings for the PCO Port are the Duotight 6.35mm Red Gas Carbonation Cap or Duotight 6.35mm Yellow Gas Carbonation Cap , and the Red PRV Cap.

Please note that the Hop Bong is not made from glass. It is made from special engineering plastic.

Capacity in Hop Pellets
150g to 180g

From: Kegland

This Hop Tube is made from 304 stainless steel and is ideal for addling larger amounts of hop pellets, flowers or spices to your RoboBrew / BrewZilla without blocking the pump. It can also be used in your Brewhouse Kettle/Boiler, 19L corny keg, and the FermZilla.

It cannot fit in a standard 50L Keg as the opening is not wide enough. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers. It will hold approximately 150g of hop pellets, allowing for some space to permit full extraction of the hop oils. Ideal for dry hopping in the keg and can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung from the keg lid or side of the vessel. 

Diameter: approx. 66mm Heigh: approx. 300 mm.

From: Kegland

This polyester bag is perfect for small grain additions or for hopping beer. It is a tube of fabric that is approximately 15cm wide and 75cm long. Both ends are open for easy cleaning and can simply be tied closed while being used. Perfect for grain or hops (suitable for use up to 110 degrees C).

Hoses play a huge role in draft beer dispensing. They carry gas from the tank to the coupler and beer from the keg right up to the faucet. These pipes are of soft, flexible but durable material. They are usually of Vinyl and Polypropylene. The hoses are also part of glycol pythons.

Hoses are connected through adapters and barbs to form the entire dispensing system. The length really depends on how far your serving point is from the keg. You might have to shorten or cut out from a large bundle. For any of this, you require a Hose and Tubing Cutter.

This cutter is sturdy and sharp that cuts right through the hose in a jiffy without leaving any rough edges too.

• Material: Plastic
• Finish: Raw
• Color: Black

Looking for a smaller option, you'll find one here.

From: Krome Dispense

A tool for cutting hose and tube, with a stainless steel blade.

From: Krome Dispense

A hydrometer is an essential tool for testing starting and finishing gravity, or sugar content, in beer or wine or spirit fermentations. This is a triple scale hydrometer - specific gravity, potential alcohol and approx. sugar per litre.

Best used with a trial jar (sold separately).

Handcraft Supplies Triple Scale Fermentation Hydrometer measures the specific gravity, potential alcohol, and approx. sugar content of any fermentable liquid, whether you're making wine, cider, beer, or distilling wash. 

Best used with a trial jar (sold separately).

Idaho 7 presents as pungent, tropical fruit and citrus (think apricot, orange, red grapefruit, papaya) with big notes of resiny pine and hints of black tea. Excellent as a single hop or part of a blend for IPA, pale ale, and other hop forward beers. 

AROMA PROFILE: BERRY, BUBBLEGUM, CITRUS, STONE FRUIT, TROPICAL

Infrared Thermometer Gun -50C to +580C (Black)

This thermometer gun has a built-in Dual laser that can be switched On and Off. Dual laser is an important feature when choosing infrared thermometers because it allows for much higher accuracy of readings. When measuring an object a Dual Laser will help greatly in finding the convergence point of the measured target and the spot ratio, which can only be achieved with Dual Laser.

Features:

• Double Laser pointer for accurate target aiming
• Simple one-handed operation
• Laser ON/OFF Switch
• Low battery indication
• LED backlight system for operation under poor illumination
• C° / °F temperature unit conversion
• Automatic Power off in 15 seconds without any operation
• Display hold, scan function

Note:
1. When using this product to measure temperature, consider the ratio between the distance (the length from the product to the measured object) and the size of the measurement area, referred to as the object distance ratio. When the distance between the product and the measured object increases, the measurement area will increase accordingly.

2. If you want to use boiled water to measure the quality of the product, please note that when measuring boiling liquids, do not allow smoke or water vapour to contact the temperature sensing area, and keep the measurement angle at 45 ~ 60 degrees.

Specifications:

• Temperature Range: -50 to 550°C
• Accuracy: ± 2% or 2°C
• Distance Spot Ratio: 12:1
• Emissivity: 0.1~1.0(Adjustable)
• Response Time Wavelength: 500ms & (8-14) um
• Repeatability: ± 1% or 1°C
• Resolution: 1°C or 1°F
• Storage Temperature: -20-50°C
• Operating Temperature: 0-50°C

From: Kegland

This unit has been designed to fit Kegland standard Single, Double and Triple Tap Kegland Kegerator Towers or any other 76mm diameter font. 

Keep your beer icy-cold with this insulated tower/font cover right out of the first drop. Most kegerators that we sell include a font fan that blows cold fridge air up the font. With that said heat loss from the stainless font surface causes the font temperature to rise meaning that a small amount of beer contributes to the "first pour foam effect".

These extra thick covers are made from 7mm neoprene, meaning your beer will stay cold even if the hot sun is beating down directly on the font.

This helps save power as your fridge will not be working as hard, and you pay less in power. So this thing practically pays for itself!

How to Install

1. Remove taps from the font. (no need to remove the shank from the font, just the taps).

2. Pull the insulated cooler down over the font.

3. Mark the tap holes and use a sharp pair of scissors to cut a hole in the neoprene jacket.

4. Re-attach the taps.

NOTE: Nail cutting scissors are particularly good for this application, or a 5/8" Hole Punch.

Please note these only come with a Kegland logo. They are not sold in plain black.

From: Kegland

Now updated with the all new duotight 8mm Ball Lock Disconnect (Grey+Red/Gas)

This kit has been designed for simplicity and ease of putting together. 

This Kit Contains:
1 x BlowTie Spunding Valve Gen 2 with 0-15psi Integrated Gauge
1 x Duotight 8mm (5/16") x Ball Lock Disconnect (Grey+ Red/Gas)
1 x Rigid 8mm Plastic Joiner

All new compact BlowTie Spunding Valve Gen2 Integrated Kit. If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job. 

If you want to control the pressure retained in a pressure vessel that is releasing pressure then the BlowTie Diaphram Spunding Valve is the tool for the job.

The adjustment knob on the top of the unit makes it easy to increase and decrease the set pressure.

This BlowTie unit can be easily disassembled for cleaning using a Phillips head screw driver.

Designed to suit 8mm OD (5/16") Evabarrier Tubing. 

Specifications:
1. Suits pressures 0-15psi (but with different gauges the unit can go above 100psi)
2. Made from food-grade acetal
3. Stainless screws
4. 8mm (5/16") push on both sides

If you are looking for a compact digital gauge with backlight illumination click here. This should only be used on a blowtie if you have excess tubing to stop liquid reaching the gauge. If liquid enters the digital gauge it will break.

A spring loaded bottling valve and adapter that connects to the Italian Barrel Tap With Locknut.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The Equal Tee 8mm can be used split gas lines or other tubing.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The FFL 1/4 Inch to 5/16 Inch (8mm) Push-fit connects to 1/4 inch MFL fittings such as the Beer MFL Ball Lock Disconnect and Gas MFL Ball Lock Disconnect and is suitable for use with 5/16 inch/8mm tubing.

Hand tighten only. Over tightening could damage the fitting.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

These valves have been designed to allow temporary servicing of downstream equipment and must only be used in the fully open or fully closed position.

DO NOT USE THESE VALVES: In a partially open position to control flow; to provide a permanent termination; without tubing assembled or plugged (or threaded connections sealed, or as a tap or “faucet”.

John Guest fittings are widely used across the commercial beer and beverage industry and are well known for being reliable high quality push fit fittings. Pushing tube into the fitting is all that is needed to produce an instant but permanent leakproof connection.

The fittings are just as easy to disconnect and re-use without the need for replacement parts.

The Two Way Divider quickly and easily splits a line into two separate lines.

Hand tighten only. Over tightening could damage the fitting.

Oxebar 20L Amber PET Keg & Pressure Fermenter Tank

The Oxebar Mono Barrier Keg by KegLand. Beverages will last 3 x Longer than competitors single PET layer kegs.

Fit up to 3 of these badboys in your Series X.1, X or 4.1 (aka XL).
Or fit up to 6 of these in a Series X.1 Plus!

Not only will it protect your beer from damaging light (amber tinting) it will also keep your beverages fresher for up to 3 times as long due to the Mono Barrier PET Polymer Matrix.

It also comes with a floating dip tube with cage filter. Is easy to undo and stack on top of each-other upside down with disconnects attached.

The 20L Oxebar Amber PET Kegs come with a Green Pressure Relief valve rated to 65psi.

Dimensions:
640mm High
235mm Diameter

Other uses:
- Overflow Homebrew Keg
- Cleaning Keg for Commercial Keg Buyers
- In a pinch it could be used as a Pressure Fermenter Tank, although we would highly recommend going for a 30L FermZilla Pressure Brewing Kit for adequate single batch sizing as well as being able to get your hand inside to clean properly.

20L Brimful, ideally 19.5L fill for Kegging purposes.

If you are going to use it as a fermenter, we would recommend between 15L and 18L. When fermenting you will need a spunding valve such as the BlowTie Spunding Valve Kit OR Integrated Gauge BlowTie Kit (0-15psi).

Remember, a PRV is a not a spunding valve.

Includes:
1 x 20L Amber Mono Barrier PET Oxebar Keg
1 x Dual PCO1881 Lid assembly with Oxebar Black Handle
1 x Green Pressure Relief Valve for Keg Lids / MK4 Reg - 65psi
1 x 100cm Silicone Hosing with Stainless Steel float and Hop Filter Cage
1 x RED Multi Gas Post Plastic Carbonation Cap
1 x Yellow Multi Liquid Post Plastic Carbonation Cap

From: Kegland

New commercial 20 litre stainless kegs with D-Type spear included and rubber base and handle.

Premium brand new kegs rated to 130psi working pressure and made using a robotic orbital welding machine with super smooth welding marks making them easier to clean. 

These kegs are also passivated, giving them a matte finish, to ensure superior rust protection.

The black rubber handles and base allows easier transportation and less scuffs on the floor of your cool room / kegerator. 

Features:
- new, with D-Type spear
- maximum working pressure: 130psi

Dimensions: approx. 240mm Diameter x 570mm High
Stated Capacity: 20 litres
Serial Numbers: No

A new 9.5 litre keg with ball-lock gas in and beer out posts, and lid with pull-ring pressure relief valve.

These premium brand new kegs with Rubber Handle are rated to 130psi working pressure and are made using a robotic orbital welding machine. They have super smooth welds, making them sanitary and easier to clean. The black rubber on these kegs also make them a little nicer to use as they are less likely to damage your floors or crack plastic lining inside your kegerator.

They also have a lid with an internal tab/hook under the lid designed specifically for attaching a hop ball for dry hopping.

Add a Carbonating Keg Lid to enable you to carbonate your beer quickly (overnight) at your standard serving pressure.

Note: Hop Ball not included.

From: Kegland
Dimensions: approx. 214mm diameter x 370mm high
Rated to: 130PSI

A brand new high quality keg.

• 19 L (5 US Gal) capacity. 
• Embossed Logo. 
• Rubber top and bottom for east transportation and stacking. 
• NSF approved for food and beverage consumption. 
• Stainless steel body. 
• Compatible with cornelius (corny) parts.
• Diameter: 22.3cm.

Add a Carbonating Keg Lid to enable you to carbonate your beer quickly (overnight) at your standard serving pressure.

A new 19 litre keg with ball-lock gas in and beer out posts, and lid with pull-ring pressure relief valve.

These new kegs are made with a high-barrier elastomer O-Rings to keep your beverage fresher for longer.

Unlike Silicone O-Rings, LOW2 O-Rings are made from synthetic M-Class Cross-Linked elastomer for superior oxygen barrier properties to prevent O2 ingress. This helps keep your beverage fresher for longer.

These premium brand new kegs are rated to 130PSI working pressure and are made using a robotic orbital welding machine. They have smooth welds making them sanitary and easier to clean. The black rubber on these kegs makes them a little nicer to use around your house as they are less likely to damage your tile floors or crack plastic lining inside your kegerator. 

They also have a lid with an internal tab/hook under the lid designed specifically for attaching a container for dry hopping.

Add a Carbonating Keg Lid to carbonate your beer quickly (overnight) at your standard serving pressure.

Dimensions: approx. 214mm Diameter x 629mm High

DO NOT USE BLEACH TO CLEAN. Bleach will break down stainless steel and causing pitting to occur.

4L PET Oxebar Keg with Cap and Handle (PCO38 )

Keep your oxygen-sensitive beverages fresher for longer with the Oxebar Monolayer. We recommend this product for storing beer up to 3-6 months.

The new lightweight and reusable plastic kegs are brought to you by Oxebar and KegLand. Store your homebrew in a more convenient size, take it away camping or to a bbq. The new shorter profile 4L under 330mm will fit in most chilly bins or esky coolers. You can also dispense with it lying on its side.

Do not Exceed 4 Bar / 58psi or 45°C

This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19L corny kegs. The small 4L size is convenient, light weight and perfect for sharing beverages with friends.

This 4L keg is light weight, compact and has extreme oxygen barrier properties. This extremely low gas transmission means your beverage will stay much fresher for longer. Even if you do consume the beverage in a short time, that short time will have much less oxygen transmission compared to other PET kegs on the market. Suitable for carbonated and non-carbonated beverages.

This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head.  The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design.

What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.

Dimensions
Diameter:155mm
Height: 325mm

Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically.  This is a very simple process and it's nothing to be feared.  We recommend that this container be pressure tested every 2 years up to 6 bar.  The instructions for this are:
1. Remove RED prv and fit GREY prv (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water.  DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar. 
4. Hold the keg at 6 bar for 1 minute
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30C

From: Kegland

8L Keg Oxebar Monolayer Keg With Cap and Handle (PCO38)

This great value re-usable plastic keg is the best way to store your home brew in a smaller sized container than traditional 19 litre corny kegs. The small 8 liter size is convenient, light weight and perfect for sharing beverages with friends.

This 8L keg is light weight, compact and has high oxygen barrier properties with 3x better (less) gas transmission than traditional PET grades of plastic making it suitable for beer storage or other oxygen sensitive carbonated and non-carbonated beverages.

This product is sold with the PCO38 cap however if you would like to dispense this product through a draft system we recommend the use of the PCO38 Tapping Head.  The tapping head is sold separately and allows you to attach standard ball lock disconnects and add a pressure relief valve to the top of this keg design. 

What is Oxebar Mono
Oxebar Mono is a PET polymer blend that utilises several polymers blended together to significantly improve gas barrier properties. When compared with standard PET plastic Oxebar Mono is able to reduce oxygen ingress and CO2 loss so your precious beverage is preserved and shelf life extended by x3. We recommend this product for beer stored in keg up to 6 months.

Dimensions
Diameter:155mm
Height: 520mm

Do not Exceed 4 Bar / 58psi or 45°C

Periodic Hydrotesting Requirement
All pressure vessels should be hydrotested periodically.  This is a very simple process and it's nothing to be feared.  We recommend that this container be pressure tested every 2 years up to 6 bar.  The instructions for this are:
1. Remove RED PRV and fit GREY PRV (you can borrow one of these from a 19L keg.
2. Fill keg to the absolute brim with water.  DO NOT forget this step.
3. Use bike pump, CO2 regulator, air compressor or any other pressure source to pressurize the keg to 6 bar. 
4. Hold the keg at 6 bar for 1 minute.
5. Release the pressure and immediately remove GREY prv and swap back to RED prv.
Note: This test should be done with the keg and water in the keg at room temperature 15-30°C

From: Kegland